Rechercher une page de manuel
Smokeping::probes::FPing
Langue: en
Version: 2008-08-29 (debian - 07/07/09)
Section: 3 (Bibliothèques de fonctions)
NAME
Smokeping::probes::FPing - FPing Probe for SmokePingSYNOPSIS
*** Probes *** +FPing binary = /usr/bin/fping # mandatory hostinterval = 1.5 mininterval = 0.001 offset = 50% packetsize = 5000 pings = 20 sourceaddress = 192.168.0.1 step = 300 timeout = 1.5 # [...] *** Targets *** probe = FPing # if this should be the default probe # [...] + mytarget # probe = FPing # if the default probe is something else host = my.host
DESCRIPTION
Integrates FPing as a probe into smokeping. The variable binary must point to your copy of the FPing program. If it is not installed on your system yet, you can get it from <http://www.fping.com/>.The (optional) packetsize option lets you configure the packetsize for the pings sent.
The FPing manpage has the following to say on this topic:
Number of bytes of ping data to send. The minimum size (normally 12) allows room for the data that fping needs to do its work (sequence number, timestamp). The reported received data size includes the IP header (normally 20 bytes) and ICMP header (8 bytes), so the minimum total size is 40 bytes. Default is 56, as in ping. Maximum is the theoretical maximum IP datagram size (64K), though most systems limit this to a smaller, system-dependent number.
VARIABLES
Supported probe-specific variables:- binary
- The location of your fping binary.
Example value: /usr/bin/fping
This setting is mandatory.
- hostinterval
- The fping ``-p'' parameter, but in (possibly fractional) seconds rather than milliseconds, for consistency with other Smokeping probes. From fping(1):
This parameter sets the time that fping waits between successive packets to an individual target.
Example value: 1.5
- mininterval
- The fping ``-i'' parameter, but in (probably fractional) seconds rather than milliseconds, for consistency with other Smokeping probes. From fping(1):
The minimum amount of time between sending a ping packet to any target.
Example value: 0.001
Default value: 0.01
- offset
- If you run many probes concurrently you may want to prevent them from hitting your network all at the same time. Using the probe-specific offset parameter you can change the point in time when each probe will be run. Offset is specified in % of total interval, or alternatively as 'random', and the offset from the 'General' section is used if nothing is specified here. Note that this does NOT influence the rrds itself, it is just a matter of when data acqusition is initiated. (This variable is only applicable if the variable 'concurrentprobes' is set in the 'General' section.)
Example value: 50%
- packetsize
- The ping packet size (in the range of 12-64000 bytes).
Example value: 5000
- pings
- How many pings should be sent to each target, if different from the global value specified in the Database section. Note that the number of pings in the RRD files is fixed when they are originally generated, and if you change this parameter afterwards, you'll have to delete the old RRD files or somehow convert them.
Example value: 20
- sourceaddress
- The fping ``-S'' parameter . From fping(1):
Set source address.
Example value: 192.168.0.1
- step
- Duration of the base interval that this probe should use, if different from the one specified in the 'Database' section. Note that the step in the RRD files is fixed when they are originally generated, and if you change the step parameter afterwards, you'll have to delete the old RRD files or somehow convert them. (This variable is only applicable if the variable 'concurrentprobes' is set in the 'General' section.)
Example value: 300
- timeout
- The fping ``-t'' parameter, but in (possibly fractional) seconds rather than milliseconds, for consistency with other Smokeping probes. Note that as Smokeping uses the fping 'counting' mode (-C), this apparently only affects the last ping.
Example value: 1.5
AUTHORS
Tobias Oetiker <tobi@oetiker.ch>Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre