Rechercher une page de manuel

Chercher une autre page de manuel:

sym.4freebsd

Langue: en

Version: 300678 (debian - 07/07/09)

Section: 4 (Pilotes et protocoles réseau)


BSD mandoc

NAME

sym - NCR/Symbios/LSI Logic 53C8XX PCI SCSI host adapter driver

SYNOPSIS

To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci device scbus device sym

To disable PCI parity checking (needed for broken bridges): options SYM_SETUP_PCI_PARITY=<boolean>

To control driver probing against HVD buses: options SYM_SETUP_SCSI_DIFF=<bit combination>

To control chip attachment balancing between the ncr driver and this driver: options SYM_SETUP_LP_PROBE_MAP=<bit combination>

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

 sym_load="YES"
 

DESCRIPTION

This driver provides support for the Symbios/LSI Logic 53C8XX PCI SCSI controllers.

Driver features include support for wide SCSI busses and fast10, fast20, fast40 and fast80-dt synchronous data transfers depending on controller capabilities. It also provides generic SCSI features such as tagged command queueing and auto-request sense. This driver is configured by default for a maximum of 446 outstanding commands per bus, 8 LUNs per target and 64 tagged tasks per LUN. These numbers are not so much limited by design as they are considered reasonable values for current SCSI technology. These values can be increased by changing appropriate constants in driver header files (not recommended).

This driver supports the entire Symbios 53C8XX family of PCI SCSI controllers. It also offers the advantage of architectural improvements available only with newer chips.

notably handles phase mismatch from SCRIPTS for the 53C896, 53C895A, and 53C1010 cores. As a result, it guarantees that no more than 1 interrupt per IO completion is delivered to the CPU, and that the SCRIPTS processor is never stalled waiting for CPU attention in normal situations.

also uses LOAD/STORE SCRIPTS instructions for chips that support it. Only the early 810, 815 and 825 NCR chips do not support LOAD/STORE. Use of LOAD/STORE instead of MEMORY MOVE allows SCRIPTS to access IO registers internal to the chip (no external PCI cycles). As a result, the driver guarantees that no PCI self-mastering will occur for chips that support LOAD/STORE.

LOAD/STORE instructions are also faster than MEMORY MOVE because they do not involve the chip DMA FIFO and are coded on 2 DWORDs instead of 3.

For the early NCR 810, 815 and 825 chips, the driver uses a separate SCRIPTS set that uses MEMORY MOVE instructions for data movements. This is because LOAD/STORE are not supported by these chips.

HVD/LVD capable controllers (895, 895A, 896, and 897) report the actual bus mode in the STEST4 chip IO registers. This feature allows the driver to safely probe against bus mode and to set up the chip accordingly. By default the driver only supports HVD for these chips. For other chips that can support HVD but not LVD, the driver has to probe implementation dependent registers (GPIO) in order to detect HVD bus mode. Only HVD implementations that conform with Symbios Logic recommendations can be detected by the driver. When the SYM_SETUP_SCSI_DIFF kernel option is assigned a value of 1, the driver will also probe against HVD for 825a, 875, 876 and 885 chips, assuming Symbios Logic compatible implementation of HVD.

When the SYM_SETUP_PCI_PARITY is assigned a value of 0, the driver will not enable PCI parity checking for 53C8XX devices. PCI parity checking should not be an option for PCI SCSI controllers, but some systems have been reported to fail using 53C8XX chips, due to spurious or permanent PCI parity errors detected. This option is supplied for convenience but it is neither recommended nor supported.

The generic ncr(4) driver also supports SYM53C8XX based PCI SCSI controllers, except for the SYM53C1010, which is only supported by the driver.

By default, when both the ncr(4) and drivers are configured, the driver takes precedence over the ncr(4) driver. The user can indicate a balancing of chip types between the two drivers by defining the SYM_SETUP_LP_PROBE_MAP kernel configuration option as follows:

Bit   Devices to be attached by ncr instead
"0x01 53C810a, 53C860"
"0x02 53C825a, 53C875, 53C876, 53C885, 53C895"
"0x0453C895a, 53C896, 53C897, 53C1510d"
"0x4053C810, 53C815, 53C825"

For example, if
SYM_SETUP_LP_PROBE_MAP is supplied with the value 0x41, the ncr(4) driver will attach to 53C810, 53C815, 53C825, 53C810a, and 53C860 based controllers, and the driver will attach to all other 53C8XX based controllers.

When only the driver is configured, the SYM_SETUP_LP_PROBE_MAP option has no effect. Thus, in this case, the driver will attach all 53C8XX based controllers present in the system.

This driver offers other options that are not currently exported to the user. They are defined and documented in the sym_conf.h driver file. Changing these options is not recommended unless absolutely necessary. Some of these options are planned to be exported through sysctl(3) or an equivalent mechanism in a future driver releases and therefore, no compatibility is guaranteed.

At initialization, the driver tries to detect and read user settings from controller NVRAM. The Symbios/Logic NVRAM layout and the Tekram NVRAM layout are currently supported. If the reading of the NVRAM succeeds, the following settings are taken into account and reported to CAM:

Host settings Symbios Tekram
"SCSI parity checking        Y       N"
"Host SCSI ident    YY"
"Verbose messagesYN"
"Scan targets hi-loYN"
"Avoid SCSI bus resetYN"
Device settings       Symbios Tekram
"Synchronous period  Y       Y"
"SCSI bus width     YY"
"Queue tag enableYY"
"Number of tagsNAY"
"Disconnect enableYY"
"Scan at boot timeYN"
"Scan LUNYN"

Devices that are configured as disabled for 'scan' in the NVRAM are not
reported to CAM at system start-up. They can be discovered later using the `camcontrol' rescan command.

The table below summarizes the main features and capabilities of the NCR/Symbios/LSI Logic 53C8XX family of PCI SCSI controllers.

Chip  Sync    Width   SRAM    PCI64   Supported
"sym53c810        10MHz 8Bit N       N       Y
"sym53c810a10MHz 8BitNNY
"sym53c81510MHz 8BitNNY
"sym53c82510MHz 16BitNNY
"sym53c825a10MHz 16Bit4KBNY
"sym53c86020MHz 8BitNNY
"sym53c87520MHz 16Bit4KBNY
"sym53c87620MHz 16Bit4KBNY
"sym53c88520MHz 16Bit4KBNY
"sym53c89540MHz 16Bit4KBNY
"sym53c895A40MHz 16Bit8KBNY
"sym53c89640MHz 16Bit8KBYY
"sym53c89740MHz 16Bit8KBYY
"sym53c1510D40MHz 16Bit4KBYY
"sym53c101080MHz 16Bit8KBYY

HARDWARE

The
driver provides support for the following Symbios/LSI Logic PCI SCSI controllers:

The SCSI controllers supported by can be either embedded on a motherboard, or on one of the following add-on boards:

MISC

The DEC KZPCA-AA is a rebadged SYM8952U.

SEE ALSO

cd(4), da(4), ncr(4), sa(4), scsi(4), camcontrol(8)

HISTORY

The driver appeared in Fx 4.0 .

AUTHORS

An -nosplit The driver was written by An Gerard Roudier and is derived from the Linux sym53c8xx driver from the same author. The sym53c8xx driver is derived from the ncr53c8xx driver, which was ported from the Fx ncr(4) driver to Linux-1.2.13. The original ncr(4) driver was written for BSD 386 and Fx by An Wolfgang Stanglmeier and An Stefan Esser .

BUGS

No known bugs.
Deviens ce que tu es.
-+- Friedrich Nietzsche -+-