hostname

Autres langues

Langue: en

Version: 369122 (fedora - 01/12/10)

Autres sections - même nom

Section: 1 (Commandes utilisateur)

NAME

hostname - show or set the system's host name
domainname - show or set the system's NIS/YP domain name
ypdomainname - show or set the system's NIS/YP domain name
nisdomainname - show or set the system's NIS/YP domain name
dnsdomainname - show the system's DNS domain name

SYNOPSIS

hostname [-v] [-a] [--alias] [-d] [--domain] [-f] [--fqdn] [-A] [--all-fqdns] [-i] [--ip-address] [-I] [--all-ip-addresses] [--long] [-s] [--short] [-y] [--yp] [--nis]
hostname [-v] [-b] [--boot] [-F filename] [--file filename] [hostname]
hostname [-v] [-h] [--help] [-V] [--version]

domainname [nisdomain] [-F file]
ypdomainname [nisdomain] [-F file]
nisdomainname [nisdomain] [-F file]

dnsdomainname [-v]

DESCRIPTION

Hostname is used to display the system's DNS name, and to display or set its hostname or NIS domain name.

GET NAME

When called without any arguments, the program displays the current names:

hostname will print the name of the system as returned by the gethostname(2) function.

domainname will print the NIS domainname of the system. domainname uses the gethostname(2) function, while ypdomainname and nisdomainname use the yp_get_default_domain(3).

dnsdomainname will print the domain part of the FQDN (Fully Qualified Domain Name). The complete FQDN of the system is returned with hostname --fqdn (but see the warnings in section THE FQDN below).

The function gethostname(2) is used to get the hostname. When the hostname -a, -d, -f or -i is called will gethostbyname(3) be called. The difference in gethostname(2) and gethostbyname(3) is that gethostbyname(3) is network aware, so it consults /etc/nsswitch.conf and /etc/host.conf to decide whether to read information in /etc/sysconfig/network or /etc/hosts

To add another dimension to this, the hostname is also set when the network interface is brought up.

SET NAME

When called with one argument or with the --file option, the commands set the host name or the NIS/YP domain name. hostname uses the sethostname(2) function, while all of the three domainname, ypdomainname and nisdomainname use setdomainname(2). Note, that this is effective only until the next reboot. After reboot original names from /etc/hosts are used again.

Note, that only the super-user can change the names.

It is not possible to set the FQDN or the DNS domain name with the dnsdomainname command (see THE FQDN below).

The host name is usually set once at system startup in /etc/rc.d/rc.sysinit (normally by reading the contents of a file which contains the host name, e.g. /etc/sysconfig/network).

THE FQDN

You can't change the FQDN (as returned by hostname --fqdn) or the DNS domain name (as returned by dnsdomainname) with this command. The FQDN of the system is the name that the resolver(3) returns for the host name.

Technically: The FQDN is the name getaddrinfo(3) returns for the host name returned by gethostname(2). The DNS domain name is the part after the first dot.

Therefore it depends on the configuration (usually in /etc/host.conf) how you can change it. Usually (if the hosts file is parsed before DNS or NIS) you can change it in /etc/hosts.

If a machine has multiple network interfaces/addresses or is used in a mobile environment, then it may either have multiple FQDNs/domain names or none at all. Therefore avoid using hostname --fqdn, hostname --domain and dnsdomainname. hostname --ip-address is subject to the same limitations so it should be avoided as well.

OPTIONS

-a, --alias
Display the alias name of the host (if used). This option is deprecated and should not be used anymore.
-b, --boot
Always set a hostname; this allows the file specified by -F to be non-existant or empty, in which case the default hostname localhost will be used if none is yet set.
-d, --domain
Display the name of the DNS domain. Don't use the command domainname to get the DNS domain name because it will show the NIS domain name and not the DNS domain name. Use dnsdomainname instead. Ssee the warnings in section THE FQDN above, and avoid using this option.
-F, --file filename
Read the host name from the specified file. Comments (lines starting with a `#') are ignored.
-f, --fqdn, --long
Display the FQDN (Fully Qualified Domain Name). A FQDN consists of a short host name and the DNS domain name. Unless you are using bind or NIS for host lookups you can change the FQDN and the DNS domain name (which is part of the FQDN) in the /etc/hosts file. See the warnings in section THE FQDN above, and avoid using this option; use hostname --all-fqdns instead.
-A, --all-fqdns
Displays all FQDNs of the machine. This option enumerates all configured network addresses on all configured network interfaces, and translates them to DNS domain names. Addresses that cannot be translated (i.e. because they do not have an appropriate reverse DNS entry) are skipped. Note that different addresses may resolve to the same name, therefore the output may contain duplicate entries. Do not make any assumptions about the order of the output.
-h, --help
Print a usage message and exit.
-i, --ip-address
Display the network address(es) of the host name. Note that this works only if the host name can be resolved. Avoid using this option; use hostname --all-ip-addresses instead.
-I, --all-ip-addresses
Display all network addresses of the host. This option enumerates all configured addresses on all network interfaces. The loopback interface and IPv6 link-local addresses are omitted. Contrary to option -i, this option does not depend on name resolution. Do not make any assumptions about the order of the output.
-s, --short
Display the short host name. This is the host name cut at the first dot.
-V, --version
Print version information on standard output and exit successfully.
-v, --verbose
Verbose output was removed.
-y, --yp, --nis
Display the NIS domain name. If a parameter is given (or --file name ) then root can also set a new NIS domain.

NOTES

The address families hostname tries when looking up the FQDN, aliases and network addresses of the host are determined by the configuration of your resolver. For instance, on GNU Libc systems, the resolver can be instructed to try IPv6 lookups first by using the inet6 option in /etc/resolv.conf.

FILES

/etc/hosts

/etc/sysconfig/network

AUTHORS

Peter Tobias, <tobias@et-inf.fho-emden.de>
Bernd Eckenfels, <net-tools@lina.inka.de> (NIS and manpage).
Michael Meskes, <meskes@debian.org>