Linux Certif

Toute la documentation sur la certification Linux LPI

lctl

NAME

lctl - Low level Lustre filesystem configuration utility

SYNOPSIS

lctl
lctl --device <devno> <command [args]>

DESCRIPTION

lctl is used to directly control Lustre via an ioctl interface, allowing various configuration, maintenance, and debugging features to be accessed.
  lctl can be invoked in interactive mode by issuing lctl command. After that, commands are issued as below. The most common commands in lctl are dl , device , network <up/down> , list_nids , ping nid , help , quit.

To get a complete listing of available commands, type help at the lctl prompt. To get basic help on the meaning and syntax of a command, type help command Command completion is activated with the TAB key, and command history is available via the up- and down-arrow keys.

For non-interactive use, one uses the second invocation, which runs command after connecting to the device.

Network Configuration

network <up/down>|<tcp/elan/myrinet>

Start or stop LNET, or select a network type for other lctl LNET commands

list_nids

Print all Network Identifiers on the local node. LNET must be running.

which_nid <nidlist>

From a list of nids for a remote node, show which interface communication will take place on.

ping <nid>

Check LNET connectivity via an LNET ping. This will use the fabric appropriate to the specified NID.

interface_list

Print the network interface information for a given network type.

peer_list

Print the known peers for a given network type.

conn_list

Print all the connected remote NIDs for a given network type.

active_tx

This command should print active transmits, and it is only used for elan network type.

route_list

Print the complete routing table.

Device Selection

device <devname>

This will select the specified OBD device. All other commands depend on the device being set.

device_list

Show all the local Lustre OBDs. AKA dl

Device Operations

conf_param <device> <parameter>

Set a permanent configuration parameter for any device via the MGS. This command must be run on the MGS node.

activate

Reactivate an import after deactivating, below.

deactivate

Deactivate an import, in particular meaning do not assign new file stripes to an OSC. This command should be used on the OSC in the MDT LOV corresponding to a failed OST device, to prevent further attempts at communication with the failed OST.

abort_recovery

Abort the recovery process on a restarting MDT or OST device

Virtual Block Device Operation

Lustre is able to emulate a virtual block device upon regular file. It is necessary to be used when you are trying to setup a swap space via file.

blockdev_attach <file name> <device node>

Attach the lustre regular file to a block device. If the device node is not existent, lctl will create it - it is recommended to create it by lctl since the emulator uses a dynamical major number.

blockdev_detach <device node>

Detach the virtual block device.

blockdev_info <device node>

Acquire which lustre file was attached to the device node.

Debug

debug_daemon

Start and stop the debug daemon, and control the output filename and size.

debug_kernel [file] [raw]

Dump the kernel debug buffer to stdout or file.

debug_file <input> [output]

Convert kernel-dumped debug log from binary to plain text format.

clear

Clear the kernel debug buffer.

mark <text>

Insert marker text in the kernel debug buffer.

filter <subsystem id/debug mask>

Filter kernel debug messages by subsystem or mask.

show <subsystem id/debug mask>

Show specific type of messages.

debug_list <subs/types>

List all the subsystem and debug types.

modules <path>

Provide gdb-friendly module information.

OPTIONS

The following options can be used to invoke lctl.

--device

The device to be used for the operation. This can be specified by name or number. See device_list

--ignore_errors | ignore_errors

Ignore errors during script processing

EXAMPLES

# lctl
lctl > dl
  0 UP mgc MGC192.168.0.20@tcp bfbb24e3-7deb-2ffa-eab0-44dffe00f692 5
  1 UP ost OSS OSS_uuid 3
  2 UP obdfilter testfs-OST0000 testfs-OST0000_UUID 3
lctl > dk /tmp/log Debug log: 87 lines, 87 kept, 0 dropped.
lctl > quit

# lctl conf_param testfs-MDT0000 sys.timeout=40

BUGS

Please report all bugs to ClusterFileSystems, support@clusterfs.com

AVAILABILITY

lctl is part of the Lustre(7) filesystem package and is available from CFS
http://clusterfs.com

SEE ALSO

Lustre(7), mkfs.lustre(8), mount.lustre(8), lctl(8), lfs(1)