smix

Langue: en

Version: 254440 (debian - 07/07/09)

Section: 1 (Commandes utilisateur)

NAME

smix - A Simple LINUX Mixer Program

SYNOPSIS

smix [-v] [-h] [-o file] [-i file] [-m file] [-s] [command(s)]

DESCRIPTION

smix , a simple mixer program that reports or controls the Mixer settings of /dev/mixer (or the specific mixer device file specified by the "-m file" option) from the command line parameter(s).

The commands are detailed below, capitals showing the minimum abbreviation allowed. Upper or lower case can be used on the command line. All Volume settings are in range 0-100 (0 min, 100 max), but these are scaled to the mixers actual range, hence set volume may be slightly different.

To see what devices/channels the mixer is configured with and to get a command summary, use smix -h .

SHow or ALL
outputs the settings of the mixer. This is the default, if no command line parameters are given
dev
outputs the current settings for the mixer device named "dev"
dev N or L,R
sets mixer device 'dev' to volume N, or to seperate left and right stereo volume L,R If device doesn't support stereo settings then max of L,R is used. The word off can be used instead of 0 and full can be used instead of 100.
ALL N or L,R
sets all mixer devices to specified volume setting (see above).
INput dev
set the DSP input to be 'dev' or 'NOne' to turn inputs off
Verbose
makes the program output the settings after doing the commands

OPTIONS

-h
show usage summary, which also lists the mixer devices and the possible input devices.
-v
be verbose - outputs the results of commands. Same as Verbose above
-i file
read commands from file
-o file
divert standard output to file.
-m file
use file instead of the default /dev/mixer . The file has to be a valid mixer device type.
-s
causes smix to output mixer settings etc in a form that can be read by smix to cause the same settings to set. This can be used to record the settings of all or part of the mixer into a file, change the settings, then get smix to reset the original settings by giving the file as an input file, see examples below.

Use '-' as a filename to indicate standard input.

EXAMPLES

smix
Displays the current mixer devices and their current settings.
smix -m /dev/mixer1
Displays the devices and their current settings for /dev/mixer1
smix input line1 line1 60 mic 0 show
sets input to line1, line1 volume to 60 and mic volume to 0 (off) and shows the total resultant mixer settings.
smix line1 60,0 show
sets left line1 input to volume 60 and right line1 input to 0 (off) and shows the resultant output.
smix -i /etc/mixer.default
set the mixer settings from smix commands in /etc/mixer.default .
smix -i -
take mixer commands from stdin, with output to stdout. If stdin and stdout is the keyboard and display, then mixer commands can by typed and executed interactively and control is retained of the mixer while smix is running.
smix -s -o mixer.conf
record the current settings of the default mixer in file mixer.conf in a form that can be fed back in to smix.
smix -i mixer.conf -o /dev/null
take the file saved, as above, and reset the mixer settings, without doing any output.

OPTIONAL CONFIGURATION FILES

Three possible configuration files can be used: a LOCAL config file (usually in current directory), a HOME config file in user's $HOME directory and a GLOBAL config file.

All the siggen suite of programs are compiled with the names of the config files built in. By default the configuration files are:

./.siggen.conf
is the LOCAL config file.
$HOME/.siggen.conf
is the HOME config file.
/etc/siggen.conf
is the GLOBAL config file.
smix -h
will indicate which config files will be searched for.

The config files do not have to exist. If they exist and are readable by the program they are used, otherwise they are simply ignored.

The config files are always searched for configuration values in the order LOCAL, HOME, GLOBAL. This allows a scheme where the sysadmin sets up default config values in the GLOBAL config file, but allows a user to set some or all different values in their own HOME config file, and to set yet more specific values when run from a particular directory.

If no configuration files exist, the program provides builtin default values, and these values can be set by appropriate command line options and flags.

See siggen.conf(5) for details of the configuration files.

smix currently looks for configuration values MIXERFILE, VERBOSE.

MIXERFILE
allows the name of the mixer device file to be changed from /dev/mixer
VERBOSE
sets whether or not to run in verbose mode.

 

SEE ALSO
siggen.conf(5)

All the other mixer programs that float around the internet.

BUGS

 

COPYING Copyright 1995-2008 Jim Jackson

The software described by this manual is covered by the GNU General Public License, Version 2, June 1991, issued by :

Free Software Foundation, Inc.,
675 Mass Ave,
Cambridge, MA 02139, USA

Permission is granted to make and distribute verbatim copies of this manual provided the copyright notice and this permission notice are preserved on all copies.

Permission is granted to copy and distribute modified versions of this manual under the conditions for verbatim copying, provided that the entire resulting derived work is distributed under the terms of a permission notice identical to this one.

Permission is granted to copy and distribute translations of this manual into another language, under the above conditions for modified versions, except that this permission notice may be included in translation instead of in the original English.

AUTHOR

Jim Jackson

Email: jj@franjam.org.uk