Linux Certif

Toute la documentation sur la certification Linux LPI

x3270.1x

NAME

x3270 - IBM host access tool

SYNOPSIS

x3270 [options] [host]

DESCRIPTION

x3270 opens a telnet connection to an IBM host in an X window. It implements RFCs 2355 (TN3270E), 1576 (TN3270) and 1646 (LU name selection), and supports IND$FILE file transfer. The window created by x3270 can use its own font for displaying characters, so it is a fairly accurate representation of an IBM 3278 or 3279. It is similar to tn3270(1) except that it is X-based, not curses-based.

The full syntax for host is:

[prefix:]...[LUname@]hostname[:port]

Prepending a P: onto hostname causes the connection to go through the telnet-passthru service rather than directly to the host. See PASSTHRU below.

Prepending an S: onto hostname removes the "extended data stream" option reported to the host. See -tn below for further information.

Prepending an N: onto hostname turns off TN3270E support for the session.

Prepending an L: onto hostname causes x3270 to first create an SSL tunnel to the host, and then create a TN3270 session inside the tunnel. (This function is supported only if x3270 was built with SSL/TLS support). Note that TLS-encrypted sessions using the TELNET START-TLS option are negotiated with the host automatically; for these sessions the L: prefix should not be used.

A specific LU name to use may be specified by prepending it to the hostname with an `@'. Multiple LU names to try can be separated by commas. An empty LU can be placed in the list with an extra comma.

The hostname may optionally be placed inside square-bracket characters `[' and `]'. This will prevent any colon `:' characters in the hostname from being interpreted as indicating option prefixes or port numbers. This allows numeric IPv6 addresses to be used as hostnames.

On systems that support the forkpty library call, the hostname may be replaced with -e and a command string. This will cause x3270 to connect to a local child process, such as a shell.

The port to connect to defaults to telnet. This can be overridden with the -port option, or by appending a port to the hostname with a colon `:'. (For compatability with previous versions of x3270 and with tn3270(1), the port may also be specified as a second, separate argument.)

OPTIONS

x3270 is a toolkit based program, so it understands standard Xt options and resources. It also understands the following options:

-activeicon

Specifies that the icon should be a miniature version of the screen image. See ICONS below.

-apl

Sets up APL mode. This is actually an abbreviation for several options. See APL SUPPORT below.

-cc range:value[,...]

Sets character classes. See CHARACTER CLASSES, below.

-charset name

Specifies an EBCDIC host character set. See CHARACTER SETS below.

-clear toggle

Sets the initial value of toggle to false. The list of toggle names is under MENUS below.

-efont name

Specifies a font for the emulator window. See FONTS below.

-iconname name

Specifies an alternate title for the program icon.

-iconx x

Specifies the initial x coordinate for the program icon.

-icony y

Specifies the initial y coordinate for the program icon.

-im method

Specifies the name of the input method to use for multi-byte input. (Supported only when x3270 is compiled with DBCS support.)

-keymap name

Specifies a keymap name and optional modifiers. See KEYMAPS below.

-keypad

Turns on the keypad as soon as x3270 starts.

-km name

Specifies the local encoding method for multi-byte text. name is an encoding name recognized by the ICU library. (Supported only when x3270 is compiled with DBCS support, and necessary only when x3270 cannot figure it out from the locale.)

-model name

The model of 3270 display to be emulated. The model name is in two parts, either of which may be omitted:

The first part is the base model, which is either 3278 or 3279. 3278 specifies a monochrome (green on black) 3270 display; 3279 specifies a color 3270 display.

The second part is the model number, which specifies the number of rows and columns. Model 4 is the default.

Model Number	Columns	Rows
2	80	24
3	80	30
4	80	43
5	132	27

Note: Technically, there is no such 3270 display as a 3279-4 or 3279-5, but most hosts seem to work with them anyway.

The default model for a color X display is 3279-4. For a monochrome X display, it is 3278-4.

-mono

Forces x3270 to believe it is running on a monochrome X display.

-once

Causes x3270 to exit after a host disconnects. This option has effect only if a hostname is specified on the command line.

-oversize colsxrows

Makes the screen larger than the default for the chosen model number. This option has effect only in combination with extended data stream support (controlled by the "x3270.extended" resource), and only if the host supports the Query Reply structured field. The number of columns multiplied by the number of rows must not exceed 16383 (3fff hex), the limit of 14-bit 3270 buffer addressing.

-port n

Specifies a different TCP port to connect to. n can be a name from /etc/services like telnet, or a number. This option changes the default port number used for all connections. (The positional parameter affects only the initial connection.)

-printerlu luname

Causes x3270 to automatically start a pr3287 printer session. If luname is ".", then the printer session will be associated with the interactive terminal session (this requires that the host support TN3270E). Otherwise, the value is used as the explicit LU name to associate with the printer session.

-proxy type:host[:port]

Causes x3270 to connect via the specified proxy, instead of using a direct connection. The host can be an IP address or hostname. The optional port can be a number or a service name. For a list of supported proxy types, see PROXY below.

-pt type

Specifies the preedit type for the multi-byte input method. Valid values are OverTheSpot, OffTheSpot, Root and OnTheSpot. The value for OverTheSpot can include an optional suffix, a signed number indicating the vertical distance in rows of the preedit window from the cursor position, e.g. OverTheSpot+1 or OverTheSpot-2. The default value is OverTheSpot+1. (Supported only when x3270 is compiled with DBCS support.)

-reconnect

Causes x3270 to automatically reconnect to the host if it ever disconnects. This option has effect only if a hostname is specified on the command line.

-sb

Turns on the scrollbar.

+sb

Turns the scrollbar off.

-scheme name

Specifes a color scheme to use in 3279 mode. This option has effect only in combination with 3279 emulation. See COLOR SCHEMES below.

-script

Causes x3270 to read commands from standard input, with the results written to standard output. The protocol for these commands is documented in x3270-script(1).

-sl n

Specifies that n lines should be saved for scrolling back. The default is 64.

-set toggle

Sets the initial value of toggle to true. The list of toggle names is under MENUS below.

-socket

Causes the emulator to create a Unix-domain socket when it starts, for use by script processes to send commands to the emulator. The socket is named /tmp/x3sck.process_id. The -p option of x3270if causes it to use this socket, instead of pipes specified by environment variables.

-tn name

Specifies the terminal name to be transmitted over the telnet connection. The default name is IBM-model_name-E, for example, IBM-3279-4-E for a color X display, or IBM-3278-4-E for a monochrome X display.

Some hosts are confused by the -E suffix on the terminal name, and will ignore the extra screen area on models 3, 4 and 5. Prepending an s: on the hostname, or setting the "x3270.extended" resource to "false", removes the -E from the terminal name when connecting to such hosts.

The name can also be specified with the "x3270.termName" resource.

-trace

Turns on data stream tracing at startup. Unlike turning it on from a menu option, there is no pop-up to confirm the file name, which defaults to /tmp/x3trc.process_id.

-tracefile file

Specifies a file to save data stream and event traces into. If the value stdout is given, then traces will be written to standard output. If the value none is given, then traces will be piped directly to the monitor window, and no file will be created.

-tracefilesize size

Places a limit on the size of a trace file. If this option is not specified, or is specified as 0 or none, the trace file will be unlimited. If specified, the trace file cannot already exist, and the (silently enforced) minimum size is 64 Kbytes. The value of size can have a K or M suffix, indicating kilobytes or megabytes respectively.

After reading resource definitions from the X server and any standandard X11 resource definition files ($HOME/.Xdefaults, etc.), x3270 will read definitions from the file $HOME/.x3270pro. This file contains local customizations and is also used to save changed options by the Save Changed Options in File menu option.

Note that -xrm options override any definitions in the .x3270pro file.

FONTS

x3270 does not use the "*font" resource for its main window. Instead, it uses a custom 14-point font called 3270, which is a close approximation of a real 3270 display and allows x3270 to display the ISO 8859-1 (Latin-1) character set and special status-line symbols. A more compact font, 3270-12, is also supported, as are the various sized fonts 3270gt8, 3270gt12, 3270gt16, 3270-20, 3270gt24, and 3270gt32. The fonts 3270h and 3270gr are also included to allow display of Hebrew and Greek text, respectively.

The font may be specified with the -efont option or the "x3270.emulatorFont" resource.

x3270 can also use any X11 font that implements the display character set required by the host EBCDIC character set.

An additional font, 3270d, is supplied. This font is identical to the default 3270 font, except that it has bitmaps defined for field attribute characters. This means that field attributes, which are normally displayed as blanks, are now visible on the screen. The characters displayed are hexadecimal codes, which can be translated using a document provided with the x3270 sources.

The font can be changed at any time through a menu option. It can also be implicitly changed by changing the size of the x3270 window with the mouse: if the window is made larger, x3270 will try to change to a larger font, and vice-versa.

CHARACTER SETS

The -charset option or the "x3270.charset" resource controls the EBCDIC host character set used by x3270. Available sets include:

Charset Name	Code Page	Display Character Sets
apl	37	3270cg-1a
belgian	500	3270cg-1a 3270-cg1 iso8859-1
bracket	37	3270cg-1a 3270-cg1 iso8859-1
brazilian	275	3270cg-1a 3270-cg1 iso8859-1
cp1047	cp1047	3270cg-1a 3270-cg1 iso8859-1
finnish	278	3270cg-1a 3270-cg1 iso8859-1
french	297	3270cg-1a 3270-cg1 iso8859-1
german	273	3270cg-1a 3270-cg1 iso8859-1
greek	423	3270cg-7
hebrew	424	3270cg-8
icelandic	871	3270cg-1a 3270-cg1 iso8859-1
hebrew	424	iso8859-8
italian	280	3270cg-1a 3270-cg1 iso8859-1
japanese	1027+300	jisx0201.1976-0 + jisx0208.1983-0
norwegian	277	3270cg-1a 3270-cg1 iso8859-1
russian	880	koi8-r
simplified-chinese	836+837	3270cg-1a iso8859-1 + gb2312.1980-0
slovenian	870	iso8859-2
spanish	284	iso8859-1
thai	838	iso8859-11 tis620.2529-0
turkish	1026	iso8859-9
uk	285	3270cg-1a 3270-cg1 iso8859-1
us-intl	37	3270cg-1a 3270-cg1 iso8859-1

The default character set is bracket, which is useful for common IBM hosts which use EBCDIC codes 0xAD and 0xBD for the `[' and `]' characters, respectively.

Most 3270 fonts implement the 3270cg-1 display character set, which is a reordered version of the ISO 8859-1 character set. Some implement the 3270cg-1a display character set, which is a superset of 3270cg-1 that includes APL2 characters. 3270h and 3270gr implement special character sets for Hebrew and Greek, respectively.

You can also specify national-language translations for your keyboard; see KEYMAPS below.

CHARACTER CLASSES

x3270 supports character classes (groupings of characters chosen with a double mouse click) in the same manner as xterm(1). The "x3270.charClass" resource or the -cc option can be used to alter the character class table. The default table is the same as xterm's; It groups letters together, and puts most punctuation characters in individual classes. To put all non-whitespace characters together in the same class (and duplicate the behavior of some early versions of x3270, use the following value:

33-127:48,161-255:48

See xterm(1) for further syntax details.

KEYPAD

A keypad may optionally be displayed, with a mouse-clickable button for each 3270 function key (these functions are also available from the keyboard). The keypad can be turned on and off by clicking on the "keypad" button in the upper-right-hand corner of the window. The "x3270.keypad" resource controls where it is displayed. Options are:

left	in a separate window, to the left of the screen
right	in a separate window, to the right of the screen
bottom	in a separate window, below the screen
integral	in the same window as the screen, below it

The default is right.

If the "x3270.keypadOn" resource is set to true, the keypad will be displayed at startup.

HOSTS DATABASE

x3270 uses the ibm_hosts database to construct a pull-down menu of hosts to connect to. It also allows host name aliases to be defined, as well as specifying macros to be executed when a connection is first made. See ibm_hosts(5) for details.

You may specify a different ibm_hosts database with the "x3270.hostsFile" resource.

COLOR SCHEMES

When emulating a 3279 display, the X colors used to draw the display are selected by two resources: the "x3270.colorScheme" resource, which gives the name of the color scheme to use, and the individual "x3270.colorScheme.xxx" resources, which give the actual definitions. The color scheme resources are documented in the Resources file with the x3270 source.

The color scheme may also be changed while x3270 is running with a selection from the Options menu.

NVT (ANSI) MODE

Some hosts use an ASCII front-end to do initial login negotiation, then later switch to 3270 mode. x3270 will emulate an ANSI X.64 terminal until the host places it in 3270 mode (telnet BINARY and SEND EOR modes, or TN3270E mode negotiation). The emulation is fairly complete; however, it is not intended to make x3270 a replacement for xterm(1).

If the host later negotiates to stop functioning in 3270 mode, x3270 will return to ANSI emulation.

In NVT mode, x3270 supports both character-at-a-time mode and line mode operation. You may select the mode with a menu option. When in line mode, the special characters and operational characteristics are defined by resources:

Mode/Character	Resource	Default
Translate CR to NL	x3270.icrnl	true
Translate NL to CR	x3270.inlcr	false
Erase previous character	x3270.erase	^?
Erase entire line	x3270.kill	^U
Erase previous word	x3270.werase	^W
Redisplay line	x3270.rprnt	^R
Ignore special meaning of next character	x3270.lnext	^V
Interrupt	x3270.intr	^C
Quit	x3270.quit	^\
End of file	x3270.eof	^D

Separate keymaps can be defined for use only when x3270 is in 3270 mode or NVT mode. See KEYMAPS for details.

MENUS

x3270 has a menu bar with three pull-down menus (File, Options, and Connect) and a button to turn the keypad on and off. The pull-down menus are also available as pop-up menus by using the "Ctrl" key and the left, middle and right mouse buttons, respectively.

The menu bar can be turned off by setting the "x3270.menuBar" resource to false.

Many sections of the File and Options menus are toggles, options that may be either on or off. The entries under the File menu are as follows:

File Transfer

Initiates transferring a file between the IBM host and the local workstation, using the IND$FILE protocol. A pop-up menu allows specifying the file names and other attributes of the transfer.
The IND$FILE program must be installed on the IBM host, and the 3270 cursor must be located in a field that will accept a TSO or VM/CMS command.

Printer Session

Starts or stops a printer session.

Trace Data Stream

If set, network traffic (both a hexadecimal representation and its interpretation) are logged to the file /tmp/x3trc.process_id, and a window is popped up to monitor the data. The file name is confirmed with a pop-up; the default directory name for the trace file can be changed with the "x3270.traceDir" resource.

Trace Keyboard/Mouse Events

If set, information about keyboard and mouse events and the actions that x3270 takes in response are logged to a file. This is the same file as used for tracing the data stream, above. Event tracing is useful for creating and debugging custom keymaps, macros and scripts. For example, it will tell you precisely what action was taken in response to pressing a particular key. If the key is not mapped, it will tell you the keysym name and keycode so you can add it to a custom keymap.

Save Screen(s) in File

If set, saves an ASCII representation of the current screen image in the file /tmp/x3scr.process_id. A pop-up allows the file name to be changed; the default directory name can be changed with the "x3270.traceDir" resource. The pop-up also has buttons to choose between saving just the current image, or continuously saving it as it is redrawn.

Print Screen Text

Pipes an ASCII representation of the screen contents to a command for printing. The default command is lpr.

Save Screen Text in File

Appends a text representation of the screen contents to a file. The data can be saved in plain ASCII or HTML.

Print Window Bitmap

Uses the xwd and xpr commands to print a copy of the graphical screen contents.

Save Changed Options in File

Saves into a file the values of all options that have been changed since x3270 was started. A pop-up allows the file name to be changed; the default file is .x3270pro in the user's home directory. If the file already exists, it is appended to. x3270 will read the contents of this file the next time it starts up. The options settings in the file override any resources defined with xrdb or in the user's .Xdefaults file; command-line switches override the file. A different options file can be specified by the X3270PRO environment variable. If the environment variable NOX3270PRO is set, no options file will be read.

Execute an Action

Allows an action name and parameters to be entered from the keyboard. This allows experimentation with actions without having to edit keymaps and repeatedly restart x3270.

The toggles under the Options menu are as follows:

Monocase

If set, x3270 operates in uppercase-only mode.

Blinking Cursor

If set, the cursor blinks once per second.

Blank Fill

If set, x3270 behaves in some un-3270-like ways. First, when a character is typed into a field, all nulls in the field to the left of that character are changed to blanks. This eliminates a common 3270 data-entry surprise. Second, in insert mode, trailing blanks in a field are treated like nulls, eliminating the annoying `lock-up' that often occurs when inserting into an field with (apparent) space at the end.

Show Timing

If set, the time taken by the host to process an AID is displayed on the status line.

Track Cursor

If set, the cursor position is displayed on the status line.

Scrollbar

If set, the scrollbar appears.

Wraparound

If set, the ANSI terminal emulator automatically assumes a NEWLINE character when it reaches the end of a line.

Paste with Left Margin

If set, puts restrictions on how pasted text is placed on the screen. The position of the cursor at the time the paste operation is begun is used as a left margin. No pasted text will fill any area of the screen to the left of that position. This option is useful for pasting into certain IBM editors that use the left side of the screen for control information.

Select by Rectangles

If set, x3270 will always select rectangular areas of the screen. Otherwise, x3270 selects by rectangles when in 3270 mode, but in ANSI mode it selects continuous regions of the screen like xterm(1).

Crosshair Cursor

If set, x3270 will display a crosshair over the cursor: lines extending the full width and height of the screen, centered over the cursor position. This makes locating the cursor on the screen much easier.

The names of the toggles for use with the -set and -clear options are as follows:

Menu Option	Name
Monocase	monoCase
Blinking Cursor	cursorBlink
Blank Fill	blankFill
Show Timing	showTiming
Track Cursor	cursorPos
Trace Data Stream	dsTrace
Trace Keyboard/Mouse Events	eventTrace
Save Screen(s) in File	screenTrace
Scrollbar	scrollBar
Wraparound	lineWrap
Paste with Left Margin	marginedPaste
Select by Rectangles	rectangleSelect
Crosshair Cursor	crosshair

In addition, the toggle altCursor can be used to select the cursor type. If set, an underline cursor will be used. If clear, the normal block cursor will be used.

These names also represent resources that can be set in your .Xdefaults or .x3270pro file. For example, if you always want to have the scrollbar on, you can add the following to your .Xdefaults or .x3270pro:

x3270.scrollBar:       true

These names are also used as the first parameter to the Toggle action.

STATUS LINE

The x3270 status line contains a variety of information. From left to right, the fields are:

comm status

The first symbol is always a 4. If x3270 is in TN3270E mode, the second symbol is a B; otherwise it is an A. If x3270 is disconnected, the third symbol is a question mark. Otherwise, if x3270 is in SSCP-LU mode, the third symbol is an S. Otherwise it is blank.

keyboard lock

If the keyboard is locked, an "X" symbol and a message field indicate the reason for the keyboard lock.

shift

Three characters indicate the keyboard modifier status. "M" indicates the Meta key, "A" the Alt key, and an up-arrow or "^" indicates the Shift key.

compose

The letter "C" indicates that a composite character is in progress. If another symbol follows the "C", it is the first character of the composite.

typeahead

The letter "T" indicates that one or more keystrokes are in the typeahead buffer.

temporary keymap

The letter "K" indicates that a temporary keymap is in effect.

reverse

The letter "R" indicates that the keyboard is in reverse field entry mode.

insert mode

A thick caret "^" or the letter "I" indicates that the keyboard is in insert mode.

printer session

The letter "P" indicates that a pr3287 session is active.

script

The letter "S" indicates that a script is active.

LU name

The LU name associated with the session, if there is one.

timing

A clock symbol and a time in seconds indicate the time it took to process the last AID or the time to connect to a host. This display is optional.

cursor position

The cursor row and column are optionally displayed, separated by a "/".

ICONS

If the -activeicon option is given (or the "x3270.activeIcon" resource is set to true), x3270 will attempt to make its icon a miniature version of the current screen image. This function is highly dependent on your window manager:

mwm

The size of the icon is limited by the "Mwm.iconImageMaximum" resource, which defaults to 50x50. The image will be clipped at the bottom and right. The icon cannot accept keyboard input.

olwm

The full screen image of all 3270 models can be displayed on the icon. However, the icon cannot be resized, so if the model is later changed with an x3270 menu option, the icon image will be corrupted. The icon cannot accept keyboard input.

twm and tvtwm

The full screen image of all 3270 models can be displayed on the icon, and the icon can be resized. The icon can accept keyboard input.

However, twm does not put labels on application-supplied icon windows. You can have x3270 add its own label to the icon by setting the "x3270.labelIcon" resource to true. The default font for icon labels is 8x13; you may change it with the "x3270.iconLabelFont" resource.

KEYMAPS

The type of keyboard may be specified with the -keymap switch or using either the KEYMAP or KEYBD environment variables. The types of supported keyboards include sun_k3, sun_k4, sun_k5, hp-k1, hp-pc and ncd.

The keymap may also be specified as a comma-separated list of names. Later definitions override earlier ones. This is used to specify both a primary keyboard type and a set of modifiers. The modifiers defined include:

ow

(OpenWindows) Swaps the middle and right mouse button definitions, so the middle button performs the "Extend" function and the right-hand button performs the "Paste" function. Also changes the cut and paste actions to use the OpenWindows CLIPBOARD.

alt

Replaces the default "Meta" key definitions with "Alt" definitions, for keyboards which do not have a "Meta" key.

apl

Allows entry of APL characters (see APL SUPPORT below).

finnish7

Replaces the bracket, brace and bar keys with common Finnish characters.

norwegian7

Replaces the bracket, brace and bar keys with common Norwegian characters.

A temporary keymap can also be specified while x3270 is running with the Keymap action. When the action Keymap(n) is executed, temporary keymap n is added to or deleted from the current keymap. Multiple temporary keymaps can be active simultaneously. The action Keymap(None) restores the original keymap. Note: When Keymap() is specified as part of a list of multiple actions in a keymap, it must be the last action in the list.

The temporary keymap hebrew is provided to allow entry of Hebrew characters.

The X Toolkit translation mechanism is used to provide keyboard emulation. It maps events into actions. The best documentation can be found with X toolkit documents, but the following should suffice for simple customization.

An Xt event consists of (at least) four fields. The first is called a modifier. It may be any combination of Meta, Shift and Ctrl. If it is prefaced by !, it means those modifiers only. The second field is the specific event, in x3270 usually just <Key>. The third field is the detail field, which gives the actual key. The name of the key may be determined using the xev program or with the "Trace X Events" menu option. The last field is the action, which is the internal emulator function. A complete list of actions may be found later in the manual.

There are three levels of translation tables in x3270. The first is a defined by the resource x3270.keymap.base. It defines alphabetic, numeric, function keys, and such basic functions as Enter and Delete. It allows a minimal useful functionality. It is generally compiled in x3270, but can be overridden.

The second level is a keyboard specific table, which is selected by the x3270.keymap resource, and defined by the x3270.keymap.name resource (where name is the value of the x3270.keymap resource). This keymap defines actions for such things as keypad keys, and keys unique to certain keyboards. Several predefined keymaps are included with x3270.

The third level is a user customizable table which may be used to augment or override key definitions. This keymap is defined by the x3270.keymap.name.user resource.

In addition, keymaps may be defined for use in 3270 mode or NVT mode only. These keymaps use the suffixes .3270 and .nvt in their names, respectively. If a keymap x3270.keymap.name.mode is defined, it will augment the keymap x3270.keymap.name when x3270 is in the given mode. If a keymap x3270.keymap.name.user.mode is defined, it will augment the keymap x3270.keymap.name.user when x3270 is in the given mode.

The default translation table x3270.keymap.base is:

<Key>Multi_key	Compose()
Shift<Key>Left	KybdSelect(Left,PRIMARY)
<Key>Left	Left()
Meta<Key>Right	NextWord()
Shift<Key>Right	KybdSelect(Right,PRIMARY)
<Key>Right	Right()
Shift<Key>Up	KybdSelect(Up,PRIMARY)
<Key>Up	Up()
Shift<Key>Down	KybdSelect(Down,PRIMARY)
<Key>Down	Down()
Ctrl<Btn1Down>	HandleMenu(quitMenu)
Ctrl<Btn2Down>	HandleMenu(optionsMenu)
Ctrl<Btn3Down>	HandleMenu(hostMenu)
Shift<Btn1Down>	MoveCursor()
<Btn1Down>	select-start()
<Btn1Motion>	select-extend()
<Btn2Down>	ignore()
<Btn2Motion>	ignore()
<Btn2Up>	insert-selection(PRIMARY)
<Btn3Down>	start-extend()
<Btn3Motion>	select-extend()
<BtnUp>	select-end(PRIMARY)
Meta<Key>F1	PF(13)
Meta<Key>F2	PF(14)
Meta<Key>F3	PF(15)
Meta<Key>F4	PF(16)
Meta<Key>F5	PF(17)
Meta<Key>F6	PF(18)
Meta<Key>F7	PF(19)
Meta<Key>F8	PF(20)
Meta<Key>F9	PF(21)
Meta<Key>F10	PF(22)
Meta<Key>F11	PF(23)
Meta<Key>F12	PF(24)
<Key>F1	PF(1)
<Key>F2	PF(2)
<Key>F3	PF(3)
<Key>F4	PF(4)
<Key>F5	PF(5)
<Key>F6	PF(6)
<Key>F7	PF(7)
<Key>F8	PF(8)
<Key>F9	PF(9)
<Key>F10	PF(10)
<Key>F11	PF(11)
<Key>F12	PF(12)
Alt<Key>q	Quit()
:<Key>	Default()

The default 3270-mode table x3270.keymap.base.3270 adds the following definitions:

Shift<Key>Return	Newline()
<Key>Return	Enter()
<Key>Linefeed	Newline()
Shift<Key>Tab	BackTab()
<Key>Tab	Tab()
<Key>Home	Home()
Meta<Key>Left	PreviousWord()
Meta<Key>Right	NextWord()
<Key>Insert	Insert()
<Key>Delete	Delete()
<Key>BackSpace	BackSpace()
Ctrl Shift<Btn1Down>	MouseSelect()
Shift<Btn1Down>	MoveCursor()
Meta<Key>1	PA(1)
Meta<Key>2	PA(2)
Meta<Key>3	PA(3)
Meta<Key>a	Attn()
Meta<Key>b	PrintWindow()
Meta<Key>c	Clear()
Meta<Key>d	Delete()
Meta<Key>h	Home()
Meta<Key>i	Insert()
Meta<Key>l	Redraw()
Meta<Key>p	PrintText()
Meta<Key>r	Reset()
Meta<Key>u	Unselect()
Ctrl<Key>u	DeleteField()
Ctrl<Key>w	DeleteWord()
:Meta<Key>asciicircum	Key(notsign)

Meta is the diamond shaped key on a sun_k4, "Alt" on an NCD, "Extend Char" on an HP. The following xmodmap command must be used on the NCD to allow use the the "Alt" key:

xmodmap -e "keysym Alt_L = Meta_L"

The left mouse button may be used to make a selection. Clicking once unselects the current selection. Clicking twice selects the word under the mouse cursor. Clicking three times selects the line under the mouse cursor. Clicking and dragging selects a rectangular area of the display.

The middle mouse button may be used to paste a selection.

The right mouse button may also be used for selections, selecting the rectangular area between the current position and where the left button was last pressed.

On color X displays, the "x3270.selectBackground" resource is used to distinguish the selected text from the rest of the screen. On monochrome X displays, selected text is in reverse video. (It can be distinguished from a block cursor because the block cursor covers slightly less than an entire character position on the screen.)

The left mouse button, when pressed with the "Shift" key held down, moves the 3270 cursor to the where the mouse cursor is pointing.

This is the complete list of keymap-callable actions. Other actions are defined for use by scripts and are documented in x3270-script(1); still others are defined for internal use by x3270 and are not documented here. Note that when an action with no parameters is used in a keymap, the parentheses and empty argument list are still required.

Actions marked with an asterisk (*) may block, sending data to the host and possibly waiting for a response.

*Attn	attention key
AltCursor	switch between block and underscore cursor
BackSpace	move cursor left (or send ASCII BS)
BackTab	tab to start of previous input field
CircumNot	input "^" in NVT mode, or "notsign" in 3270 mode
*Clear	clear screen
Compose	next two keys form a special symbol
*Connect(host)	connect to host
*CursorSelect	Cursor Select AID
Cut	erase selected text
Default	enter key literally
Delete	delete character under cursor (or send ASCII DEL)
DeleteField	delete the entire field
DeleteWord	delete the current or previous word
*Disconnect	disconnect from host
Down	move cursor down
Dup	duplicate field
*Enter	Enter AID (or send ASCII CR)
Erase	erase previous character (or send ASCII BS)
EraseEOF	erase to end of current field
EraseInput	erase all input fields
Execute(cmd)	execute a command in a shell
FieldEnd	move cursor to end of field
FieldMark	mark field
HandleMenu(name)	pop up a menu
HexString(hex_digits)	insert control-character string
Home	move cursor to first input field
Insert	set insert mode
*Interrupt	send TELNET IP to host
Key(keysym)	insert key keysym
Key(0xxx)	insert key with ASCII code xx
Keymap(keymap)	toggle alternate keymap (or remove with None)
KybdSelect(direction[,atom...])	Extend selection by one row or column
Left	move cursor left
Left2	move cursor left 2 positions
*Macro(macro)	run a macro
MonoCase	toggle uppercase-only mode
MoveCursor	move cursor to mouse position
MoveCursor(row, col)	move cursor to (row,col)
*MoveCursorSelect	move cursor to mouse position, light pen selection
Newline	move cursor to first field on next line (or send ASCII LF)
NextWord	move cursor to next word
*PA(n)	Program Attention AID (n from 1 to 3)
*PF(n)	Program Function AID (n from 1 to 24)
PreviousWord	move cursor to previous word
Printer(Start[,lu]|Stop)	start or stop printer session
PrintText(command)	print screen text on printer
PrintWindow(command)	print screen image (bitmap) on printer
Quit	exit x3270
*Reconnect	reconnect to previous host
Redraw	redraw window
Reset	reset locked keyboard
Right	move cursor right
Right2	move cursor right 2 positions
SetFont(font)	change emulator font
*Script(command[,arg...])	run a script
*String(string)	insert string (simple macro facility)
*SysReq	System Request AID
Tab	move cursor to next input field
Toggle(option[,set|clear])	toggle an option
ToggleInsert	toggle insert mode
ToggleReverse	toggle reverse-input mode
*Transfer(option=value...)	file transfer
Unselect	release selection
Up	move cursor up
(the following are similar to xterm)
ignore	do nothing
insert-selection([atom[,atom...]])	paste selection
move-select	a combination of MoveCursor and select-start
select-end(atom[,atom...]])	complete selection and assign to atom(s)
select-extend	move the end of a selection
select-start	mark the beginning of a selection
set-select(atom[,atom...]])	assign existing selection to atom(s)
start-extend	begin marking the end of a selection

MACROS AND SCRIPTS

There are several types of macros and script functions available.

The String Action

The simplest method for macros is provided via the String action. The arguments to String are one or more double-quoted strings which are inserted directly as if typed. The C backslash conventions are honored as follows. (Entries marked * mean that after sending the AID code to the host, x3270 will wait for the host to unlock the keyboard before further processing the string.)

\b	Left
\f	Clear*
\n	Enter*
\pan	PA(n)*
\pfnn	PF(nn)*
\r	Newline
\t	Tab
\T	BackTab

An example keymap entry would be:

Meta<Key>p: String("probs clearrdr\n")

Note: The strings are in ASCII and converted to EBCDIC, so beware of inserting control codes. Also, a backslash before a p may need to be doubled so it will not be removed when a resource file is read.

There is also an alternate form of the String action, HexString, which is used to enter non-printing data. The argument to HexString is a string of hexadecimal digits, two per character. A leading 0x or 0X is optional. In 3270 mode, the hexadecimal data represent EBCDIC characters, which are entered into the current field. In NVT mode, the hexadecimal data represent ASCII characters, which are sent directly to the host.

The Script Action

This action causes x3270 to start a child process which can execute x3270 actions. Standard input and output from the child process are piped back to x3270. The Script action is fully documented in x3270-script(1).

The macros Resource

An alternate method of defining macros is the "x3270.macros" resource. This resource is similar to a keymap, but instead of defining keyboard mappings, it associates a list of X actions with a name. These names are displayed on a Macros menu that appears when x3270 is connected to a host. Selecting one of the names on the menu executes the X actions associated with it. Typically the actions are String calls, but any action may be specified. Here is a sample macros resource definition, which would result in a four-entry Macros menu:

x3270.macros: \
       log off: String("logout\n")\n\

       vtam: String("dial vtam\n")\n\

       pa1: PA(1)\n\

       alt printer: PrintText("lpr -Plw2")

You can also define a different set of macros for each host. If there is a resource named `x3270.macros.somehost', it defines the macros menu for when x3270 is connected to somehost.

The -script Option

This facility allows x3270 to operate under the complete control of a script. x3270 accepts actions from standard input, and prints results on standard output. The -script option is fully documented in x3270-script(1).

COMPOSITE CHARACTERS

x3270 allows the direct entry of accented letters and special symbols. Pressing and releasing the "Compose" key, followed by two other keys, causes entry of the symbol combining those two keys. For example, "Compose" followed by the "C" key and the "," (comma) key, enters the "C-cedilla" symbol. A C on the status line indicates a pending composite character.

The mappings between these pairs of ordinary keys and the symbols they represent is controlled by the "x3270.composeMap" resource; it gives the name of the map to use. The maps themselves are named "x3270.composeMap.name". The default is "latin1", which gives mappings for most of the symbols in the ISO 8859-1 Latin-1 character set that are not in the 7-bit ASCII character set.

Note: The default keymap defines the "Multi_key" keysym as the "Compose" key. If your keyboard lacks such a key, you may set up your own "Compose" key with a keymap that maps some other keysym onto the Compose action.

APL SUPPORT

x3270 supports the full APL2 character set and the entry of APL characters from the keyboard.

APL characters are supported only in the special 3270 font.

Keyboard entry of APL characters is supported through the apl keymap modifier. This modifier defines the "Alt" key as an APL key, with a typical APL keyboard layout, e.g., "Alt" pressed with the A key results in the APL "alpha" symbol. Overstruck characters such as "quad-quote" are not defined as single keystrokes; instead they are entered as composites (see COMPOSITE CHARACTERS above). A special composite map, apl, is provided for this purpose.

Note: Some keyboards do not define the "Alt" key as a modifier, so keymaps that use the "Alt" key will not function. On a Sun for example, this can be remedied with the command:

xmodmap -e "add mod2 = Alt_L"

For convenience, an -apl option is defined, which is an abbreviation for the following resource definitions:

x3270.keymap: your_keymap_name,apl
x3270.charset: apl
x3270.composeMap: apl

There are a number of APL characters that are similar in appearance to non-APL characters. In particular, the APL "stile", "slope," "tilde" and "quotedot" characters are similar to the EBCDIC "bar", "backslash," "tilde" and "exclaim" characters. The APL characters are entered with the "Alt" key, and have slightly different appearances.

The complete list of special APL keysyms is as follows. Entries marked with an asterisk (*) represent simple aliases for standard EBCDIC characters. Entries marked with an (S) represent Sharp APL charatcers.

APL Symbol	Hex	x3270 Keysym	x3270 Key	x3270 Composed Keys
A underbar	41	apl_Aunderbar	Alt-A	A + underbar
alpha	B0	apl_alpha	Alt-a
B underbar	42	apl_Bunderbar	Alt-B	B + underbar
bar	60*	apl_bar	-
brace left	C0	apl_braceleft	Alt-{
brace right	D0	apl_braceright	Alt-}
C underbar	43	apl_Cunderbar	Alt-C	C + underbar
circle	9D	apl_circle	Alt-o
circle bar	ED	apl_circlebar		circle + bar
circle slope	CF	apl_circleslope		circle + slope
circle star	FD	apl_circlestar		circle + star
circle stile	CD	apl_circlestile		circle + stile
colon	7A*	apl_colon	:
comma	6B*	apl_comma	,
comma bar (S)	E5	apl_commabar		comma + bar
D underbar	44	apl_Dunderbar	Alt-D	D + underbar
del	BA	apl_del	Alt-g
del stile	DC	apl_delstile		del + stile
del tilde	FB	apl_deltilde		del + tilde
delta	BB	apl_delta	Alt-h
delta stile	DD	apl_deltastile		delta + stile
delta underbar	FC	apl_deltaunderbar		delta + underbar
diamond	70	apl_diamond		up caret + down caret
dieresis	72	apl_dieresis	Alt-1
dieresis circle (S)	E5	apl_dieresiscircle		dieresis + circle
dieresis dot	EC	apl_dieresisdot		dieresis + dot
dieresis jot (S)	E4	apl_dieresisjot		dieresis + jot
divide	B8	apl_divide	Alt-+
dot	4B*	apl_dot
down arrow	8B	apl_downarrow	Alt-u
down caret	78	apl_downcaret	Alt-9
down caret tilde	CB	apl_downcarettilde		down caret + tilde
down shoe	AB	apl_downshoe	Alt-v
down stile	8E	apl_downstile	Alt-d
down tack	AC	apl_downtack	Alt-b
down tack jot	FE	apl_downtackjot		down tack + jot
down tack up tack	DA	apl_downtackuptack		down tack + up tack
E underbar	45	apl_Eunderbar	Alt-E	E + underbar
epsilon	B1	apl_epsilon	Alt-e
epsilon underbar	75	apl_epsilonunderbar		epsilon + underbar
equal	7E*	apl_equal	"="
equal underbar	E1	apl_equalunderbar		equal + underbar
euro (S)	E7	apl_euro		C + =
F underbar	46	apl_Funderbar	Alt-F	F + underbar
G underbar	47	apl_Gunderbar	Alt-G	G + underbar
greater	6E*	apl_greater	>
H underbar	48	apl_Hunderbar	Alt-H	H + underbar
I underbar	49	apl_Iunderbar	Alt-I	I + underbar
iota	B2	apl_iota	Alt-i
iota underbar	74	apl_iotaunderbar		iota + underbar
J underbar	51	apl_Junderbar	Alt-J	J + underbar
jot	AF	apl_jot	alt-j
K underbar	52	apl_Kunderbar	Alt-K	K + underbar
L underbar	53	apl_Lunderbar	Alt-L	L + underbar
left arrow	9F	apl_leftarrow	Alt-[
left bracket	AD	apl_leftbracket	[
left paren	4D*	apl_leftparen	(
left shoe	9B	apl_leftshoe	Alt-z
less	4C*	apl_less	<
M underbar	54	apl_Munderbar	Alt-M	M + underbar
N underbar	55	apl_Nunderbar	Alt-N	N + underbar
not equal	BE	apl_notequal	Alt-8	equal + slash
not greater	8C	apl_notgreater	Alt-4	less + equal
not less	AE	apl_notless	Alt-6	greater + equal
O underbar	56	apl_Ounderbar	Alt-O	O + underbar
omega	B4	apl_omega	Alt-w
overbar	A0	apl_overbar	Alt-2
P underbar	57	apl_Punderbar	Alt-P	P + underbar
plus	4E*	apl_plus	+
Q underbar	58	apl_Qunderbar	Alt-Q	Q + underbar
quad	90	apl_quad	Alt-l
quad divide	EE	apl_quaddivide		quad + divide
quad jot	73	apl_quadjot		quad + jot
quad quote	DE	apl_quadquote		quad + quote
quad slope	CE	apl_quadslope		quad + slope
query	6F*	apl_query	?
quote	7D*	apl_quote
quote dot	DB	apl_quotedot		quote + dot
R underbar	59	apl_Runderbar	Alt-R	R + underbar
rho	B3	apl_rho	Alt-r
right arrow	8F	apl_rightarrow	Alt-]
right bracket	BD	apl_rightbracket	]
right paren	5D*	apl_rightparen	)
right shoe	9A	apl_rightshoe	Alt-x
S underbar	62	apl_Sunderbar	Alt-S	S + underbar
semicolon	5E*	apl_semicolon	;
slash	61*	apl_slash	/
slash bar	EA	apl_slashbar		slash + bar
slope	B7	apl_slope	Alt-\
slope bar	EB	apl_slopebar		slope + bar
squad	CC	apl_squad		quad + quad
star	5C*	apl_star	*
stile	BF	apl_stile	Alt-|
T underbar	63	apl_Tunderbar	Alt-T	T + underbar
tilde	80	apl_tilde	Alt-~
times	B6	apl_times	Alt-=
U underbar	64	apl_Uunderbar	Alt-U	U + underbar
underbar	6D*	apl_underbar	"_"
up arrow	8A	apl_uparrow	Alt-y
up caret	71	apl_upcaret	Alt-0
up caret tilde	CA	apl_upcarettilde		up caret + tilde
up shoe	AA	apl_upshoe	Alt-c
up shoe jot	DF	apl_upshoejot		up shoe + jot
up stile	8D	apl_upstile	Alt-s
up tack	BC	apl_uptack	Alt-n
up tack jot	EF	apl_uptackjot		up tack + jot
V underbar	65	apl_Vunderbar	Alt-V	V + underbar
W underbar	66	apl_Wunderbar	Alt-W	W + underbar
X underbar	67	apl_Xunderbar	Alt-X	X + underbar
Y underbar	68	apl_Yunderbar	Alt-Y	Y + underbar
Z underbar	69	apl_Zunderbar	Alt-Z	Z + underbar

XIM SUPPORT

When compiled with DBCS support, x3270 supports multi-byte input methods via the XIM protocol.

The input method is selected by the XMODIFIERS environment variable or the -im command-line option.

The preedit type is specified by the -pt command-line option, with a default of OverTheSpot+1.

SCREEN PRINTING

Screen printing is handled through options on the File menu or by the PrintText and PrintWindow actions. Each results in a pop-up to confirm the print command.

The PrintText action (usually assigned to the key <Meta>p) sends the current screen image to the printer as ASCII characters. The default command used to print the data is controlled by the "x3270.printTextCommand" resource; the default is lpr. You may also use a keymap definition to pass a print command the PrintText action itself. The command receives the screen text as its standard input. For example, the following keymap will save the screen text in a file:

Meta<Key>f: PrintText("cat >screen.image")

Note: HardPrint is an alias for PrintText.

The PrintWindow action (usually assigned to the key <Meta>b) sends the current screen image to the printer as a bitmap. The default command used to print the data is controlled by the "x3270.printWindowCommand" resource; the default is

xwd -id %d | xpr | lpr.

You may also use a keymap definition to pass a print command to the PrintWindow action itself. If the command contains the text "%d", the window ID of x3270 will be substituted before it is run. For example, the following keymap will pop up a duplicate of the current screen image:

Meta<Key>g: PrintWindow("xwd -id %d | xwud &")

If the command for PrintWindow or PrintText begins with an "@" character, the initial pop-up menu to confirm the print command is not displayed and the command cannot be edited.

BUGS

Cursor highlighting will not work with if you use the NoTitleFocus option in your .twmrc file.

PASSTHRU

x3270 supports the Sun telnet-passthru service provided by the in.telnet-gw server. This allows outbound telnet connections through a firewall machine. When a p: is prepended to a hostname, x3270 acts much like the itelnet(1) command. It contacts the machine named internet-gateway at the port defined in /etc/services as telnet-passthru (which defaults to 3514). It then passes the requested hostname and port to the in.telnet-gw server.

PROXY

The -proxy option or the x3270.proxy resource causes x3270 to use a proxy server to connect to the host. The syntax of the option or resource is:

type:host[:port]

The supported values for type are:

Proxy Type	Protocol	Default Port
http	RFC 2817 HTTP tunnel (squid)	3128
passthru	Sun in.telnet-gw	none
socks4	SOCKS version 4	1080
socks5	SOCKS version 5 (RFC 1928)	1080
telnet	No protocol (just send connect host port)	none

The special types socks4a and socks5d can also be used to force the proxy server to do the hostname resolution for the SOCKS protocol.

FILES

/usr/lib/X11/x3270/ibm_hosts
$HOME/.x3270pro

ENVIRONMENT VARIABLES

3270PRO Path of profile file, containing resource definitions. Merged after the system resource database, but before X3270RDB. Defaults to $HOME/.x3270pro.
NOX3270PRO If set, do not read the profile.
X3270RDB Additional resource definitions, merged after the profile file but before the command-line options.
KEYMAP Keymap name.
KEYBD Keymap name.

SEE ALSO

s3270(1), c3270(1), tcl3270(1), ibm_hosts(5), x3270-script(1), pr3287(1), telnet(1), tn3270(1)
X Toolkit Intrinsics
Data Stream Programmer's Reference, IBM GA23-0059
Character Set Reference, IBM GA27-3831
RFC 1576, TN3270 Current Practices
RFC 1646, TN3270 Extensions for LUname and Printer Selection
RFC 2355, TN3270 Enhancements

COPYRIGHTS

Modifications and original code Copyright 1993, 1994, 1995, 1996, 1997, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007 by Paul Mattes.
DFT File Transfer Code Copyright October 1995 by Dick Altenbern.
RPQNAMES Code Copyright 2004, 2005 by Don Russell.
Original X11 Port Copyright 1990 by Jeff Sparkes.

Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in supporting documentation.

Copyright 1989 by Georgia Tech Research Corporation, Atlanta, GA 30332.

All Rights Reserved. GTRC hereby grants public use of this software. Derivative works based on this software must incorporate this copyright notice.

x3270 is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the file LICENSE for more details.

VERSION

x3270 3.3.6