Rechercher une page de manuel
SNMP::Info::Layer3::Enterasys.3pm
Langue: en
Version: 2007-11-25 (mandriva - 01/05/08)
Section: 3 (Bibliothèques de fonctions)
NAME
SNMP::Info::Layer3::Enterasys - SNMP Interface to Enterasys Network DevicesAUTHOR
Eric MillerSYNOPSIS
# Let SNMP::Info determine the correct subclass for you. my $enterasys = new SNMP::Info( AutoSpecify => 1, Debug => 1, # These arguments are passed directly on to SNMP::Session DestHost => 'myswitch', Community => 'public', Version => 1 ) or die "Can't connect to DestHost.\n";
my $class = $enterasys->class();
print "SNMP::Info determined this device to fall under subclass : $class\n";
DESCRIPTION
Provides abstraction to the configuration information obtainable from an Enterasys device through SNMP.For speed or debugging purposes you can call the subclass directly, but not after determining a more specific class using the method above.
my $enterasys = new SNMP::Info::Layer3::Enterasys(...);
Inherited Classes
- SNMP::Info::MAU
- SNMP::Info::LLDP
- SNMP::Info::CDP
- SNMP::Info::Layer3
Required MIBs
- ENTERASYS-OIDS-MIB
Inherited MIBs
See ``Required MIBs'' in SNMP::Info::MAU for its MIB requirements.
See ``Required MIBs'' in SNMP::Info::LLDP for its MIB requirements.
See ``Required MIBs'' in SNMP::Info::CDP for its MIB requirements.
See ``Required MIBs'' in SNMP::Info::Layer3 for its MIB requirements.
GLOBALS
These are methods that return scalar value from SNMP- $enterasys->model()
- Returns model type. Checks $enterasys->id() against the ENTERASYS-OIDS-MIB.
- $enterasys->vendor()
- Returns enterasys
- $enterasys->os()
- Returns enterasys
- $enterasys->mac()
- Returns base mac
(dot1dBaseBridgeAddress)
Overrides
Globals imported from SNMP::Info::MAU
See documentation in ``GLOBALS'' in SNMP::Info::MAU for details.
Globals imported from SNMP::Info::LLDP
See documentation in ``GLOBALS'' in SNMP::Info::LLDP for details.
Globals imported from SNMP::Info::CDP
See documentation in ``GLOBALS'' in SNMP::Info::CDP for details.
Globals imported from SNMP::Info::Layer3
See documentation in ``GLOBALS'' in SNMP::Info::Layer3 for details.
TABLE METHODS
These are methods that return tables of information in the form of a reference to a hash.Overrides
- $enterasys->i_ignore()
- Returns reference to hash. Creates a key for each IID that should be ignored.
Currently looks for rs232, tunnel,loopback,lo,null from $enterasys->interfaces()
- $enterasys->i_duplex()
- See documentation for mau_i_duplex() in ``TABLE METHODS'' in SNMP::Info::MAU.
- $enterasys->i_duplex_admin()
- See documentation for mau_i_duplex_admin() in ``TABLE METHODS'' in SNMP::Info::MAU.
Topology information
Based upon the firmware version Enterasys devices may support Cabletron Discovery Protocol (CTRON-CDP), Cisco Discovery Protocol (CDP), Link Layer Discovery Protocol (LLDP), or all. This module currently supports CDP and LLDP, but not CTRON-CDP. These methods will query both CDP and LLDP and return the combination of all information. As a result, there may be identical topology information returned from the two protocols causing duplicate entries. It is the calling program's responsibility to identify any duplicate entries and de-duplicate if necessary.
- $enterasys->hasCDP()
- Returns true if the device is running either CDP or LLDP.
- $enterasys->c_if()
- Returns reference to hash. Key: iid Value: local device port (interfaces)
- $enterasys->c_ip()
- Returns reference to hash. Key: iid Value: remote IPv4 address
If multiple entries exist with the same local port, c_if(), with the same IPv4 address, c_ip(), it may be a duplicate entry.
If multiple entries exist with the same local port, c_if(), with different IPv4 addresses, c_ip(), there is either a non-CDP/LLDP device in between two or more devices or multiple devices which are not directly connected.
Use the data from the Layer2 Topology Table below to dig deeper.
- $enterasys->c_port()
- Returns reference to hash. Key: iid Value: remote port (interfaces)
- $enterasys->c_id()
- Returns reference to hash. Key: iid Value: string value used to identify the chassis component associated with the remote system.
- $enterasys->c_platform()
- Returns reference to hash. Key: iid Value: Remote Device Type
Table Methods imported from SNMP::Info::MAU
See documentation in ``TABLE METHODS'' in SNMP::Info::MAU for details.
Table Methods imported from SNMP::Info::LLDP
See documentation in ``TABLE METHODS'' in SNMP::Info::LLDP for details.
Table Methods imported from SNMP::Info::CDP
See documentation in ``TABLE METHODS'' in SNMP::Info::CDP for details.
Table Methods imported from SNMP::Info::Layer3
See documentation in ``TABLE METHODS'' in SNMP::Info::Layer3 for details.
Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre