Linux Certif

Toute la documentation sur la certification Linux LPI

in.telnetd

BSD mandoc

NAME

in.telnetd - DARPA TELNET protocol server

SYNOPSIS

in.telnetd [-Uhlkn46H ] [-D debugmode ] [-I initid ] [-S tos ] [-X authtype ] [-r lowpty-highpty ] [-u len ] [-L /bin/login ] [-debug [port ] ]

DESCRIPTION

The in.telnetd command is a server which supports the DARPA standard TELNET virtual terminal protocol. in.telnetd is normally invoked by the internet server (see inetd(8)) for requests to connect to the TELNET port as indicated by the /etc/services file (see services(5)). The -debug option may be used to start up in.telnetd manually, instead of through inetd(8). If started up this way, port may be specified to run in.telnetd on an alternate TCP port number.

The in.telnetd command accepts the following options:

-D debugmode

This option may be used for debugging purposes. This allows in.telnetd to print out debugging information to the connection, allowing the user to see what in.telnetd is doing. There are several possible values for debugmode

options

Prints information about the negotiation of TELNET options.

report

Prints the options information, plus some additional information about what processing is going on.

netdata

Displays the data stream received by in.telnetd

ptydata

Displays data written to the pty.

exercise

Has not been implemented yet.

-debug

Enables debugging on each socket created by in.telnetd (see SO_DEBUG in socket(2)).

-h

Disables the printing of host-specific information before login has been completed.

-H

Instruct the login program to suppress printing the hostname before the prompt.

-I initid

This option is only applicable to UNICOS systems prior to 7.0. It specifies the ID from /etc/inittab to use when init starts login sessions. The default ID is ``fe''

-k

This option is only useful if in.telnetd has been compiled with both linemode and kludge linemode support. If the -k option is specified, then if the remote client does not support the LINEMODE option, then in.telnetd will operate in character at a time mode. It will still support kludge linemode, but will only go into kludge linemode if the remote client requests it. (This is done by the client sending DONT SUPPRESS-GO-AHEAD and DONT ECHO . The -k option is most useful when there are remote clients that do not support kludge linemode, but pass the heuristic (if they respond with WILL TIMING-MARK in response to a DO TIMING-MARK) for kludge linemode support.

-l

Specifies line mode. Tries to force clients to use line-at-a-time mode. If the LINEMODE option is not supported, it will go into kludge linemode.

-n

Disable TCP keep-alives. Normally in.telnetd enables the TCP keep-alive mechanism to probe connections that have been idle for some period of time to determine if the client is still there, so that idle connections from machines that have crashed or can no longer be reached may be cleaned up.

-r lowpty-highpty

This option is only enabled when in.telnetd is compiled for UNICOS It specifies an inclusive range of pseudo-terminal devices to use. If the system has sysconf variable _SC_CRAY_NPTY configured, the default pty search range is 0 to _SC_CRAY_NPTY; otherwise, the default range is 0 to 128. Either lowpty or highpty may be omitted to allow changing either end of the search range. If lowpty is omitted, the - character is still required so that in.telnetd can differentiate highpty from lowpty

-S tos

-u len

This option is used to specify the size of the field in the utmp structure that holds the remote host name. If the resolved host name is longer than len the dotted decimal value will be used instead. This allows hosts with very long host names that overflow this field to still be uniquely identified. Specifying -u0 indicates that only dotted decimal addresses should be put into the utmp file.

-U

This option causes in.telnetd to refuse connections from addresses that cannot be mapped back into a symbolic name via the via the gethostbyaddr(3) routine.

-X authtype

This option is only valid if in.telnetd has been built with support for the authentication option. It disables the use of authtype authentication, and can be used to temporarily disable a specific authentication type without having to recompile in.telnetd

-L pathname

Specify pathname to an alternative login program.

-4

-6

Specifies address family to be used on -debug mode. During normal operation Po called from inetd(8) Pc in.telnetd will use the file descriptor passed from inetd(8).

in.telnetd operates by allocating a pseudo-terminal device (see pty(4)) for a client, then creating a login process which has the slave side of the pseudo-terminal as stdin stdout and stderr in.telnetd manipulates the master side of the pseudo-terminal, implementing the TELNET protocol and passing characters between the remote client and the login process.

When a TELNET session is started up, in.telnetd sends TELNET options to the client side indicating a willingness to do the following TELNET options, which are described in more detail below:

DO AUTHENTICATION

WILL ENCRYPT

DO TERMINAL TYPE

DO TSPEED

DO XDISPLOC

DO NEW-ENVIRON

DO ENVIRON

WILL SUPPRESS GO AHEAD

DO ECHO

DO LINEMODE

DO NAWS

WILL STATUS

DO LFLOW

DO TIMING-MARK

The pseudo-terminal allocated to the client is configured to operate in ``cooked'' mode, and with XTABS and CRMOD enabled (see tty(4)).

in.telnetd has support for enabling locally the following TELNET options:

"WILL ECHO"

When the LINEMODE option is enabled, a WILL ECHO or WONT ECHO will be sent to the client to indicate the current state of terminal echoing. When terminal echo is not desired, a WILL ECHO is sent to indicate that in.telnetd will take care of echoing any data that needs to be echoed to the terminal, and then nothing is echoed. When terminal echo is desired, a WONT ECHO is sent to indicate that in.telnetd will not be doing any terminal echoing, so the client should do any terminal echoing that is needed.

"WILL BINARY"

Indicates that the client is willing to send a 8 bits of data, rather than the normal 7 bits of the Network Virtual Terminal.

"WILL SGA"

Indicates that it will not be sending IAC GA go ahead, commands.

"WILL STATUS"

Indicates a willingness to send the client, upon request, of the current status of all TELNET options.

"WILL TIMING-MARK"

Whenever a DO TIMING-MARK command is received, it is always responded to with a WILL TIMING-MARK

"WILL LOGOUT"

When a DO LOGOUT is received, a WILL LOGOUT is sent in response, and the TELNET session is shut down.

"WILL ENCRYPT"

Only sent if in.telnetd is compiled with support for data encryption, and indicates a willingness to decrypt the data stream.

in.telnetd has support for enabling remotely the following TELNET options:

"DO BINARY"

Sent to indicate that in.telnetd is willing to receive an 8 bit data stream.

"DO LFLOW"

Requests that the client handle flow control characters remotely.

"DO ECHO"

This is not really supported, but is sent to identify a BSD 4.2 telnet(1) client, which will improperly respond with WILL ECHO If a WILL ECHO is received, a DONT ECHO will be sent in response.

"DO TERMINAL-TYPE"

Indicates a desire to be able to request the name of the type of terminal that is attached to the client side of the connection.

"DO SGA"

Indicates that it does not need to receive IAC GA the go ahead command.

"DO NAWS"

Requests that the client inform the server when the window (display) size changes.

"DO TERMINAL-SPEED"

Indicates a desire to be able to request information about the speed of the serial line to which the client is attached.

"DO XDISPLOC"

Indicates a desire to be able to request the name of the X windows display that is associated with the telnet client.

"DO NEW-ENVIRON"

Indicates a desire to be able to request environment variable information, as described in RFC 1572.

"DO ENVIRON"

Indicates a desire to be able to request environment variable information, as described in RFC 1408.

"DO LINEMODE"

Only sent if in.telnetd is compiled with support for linemode, and requests that the client do line by line processing.

"DO TIMING-MARK"

Only sent if in.telnetd is compiled with support for both linemode and kludge linemode, and the client responded with WONT LINEMODE If the client responds with WILL TM the it is assumed that the client supports kludge linemode. Note that the [-k ] option can be used to disable this.

"DO AUTHENTICATION"

Only sent if in.telnetd is compiled with support for authentication, and indicates a willingness to receive authentication information for automatic login.

"DO ENCRYPT"

Only sent if in.telnetd is compiled with support for data encryption, and indicates a willingness to decrypt the data stream.

FILES

/etc/services

/etc/inittab

(UNICOS systems only)

/etc/iptos

(if supported)

SEE ALSO

login(1), telnet(1)

STANDARDS

RFC-854

TELNET PROTOCOL SPECIFICATION

RFC-855

TELNET OPTION SPECIFICATIONS

RFC-856

TELNET BINARY TRANSMISSION

RFC-857

TELNET ECHO OPTION

RFC-858

TELNET SUPPRESS GO AHEAD OPTION

RFC-859

TELNET STATUS OPTION

RFC-860

TELNET TIMING MARK OPTION

RFC-861

TELNET EXTENDED OPTIONS - LIST OPTION

RFC-885

TELNET END OF RECORD OPTION

RFC-1073

Telnet Window Size Option

RFC-1079

Telnet Terminal Speed Option

RFC-1091

Telnet Terminal-Type Option

RFC-1096

Telnet X Display Location Option

RFC-1123

Requirements for Internet Hosts -- Application and Support

RFC-1184

Telnet Linemode Option

RFC-1372

Telnet Remote Flow Control Option

RFC-1416

Telnet Authentication Option

RFC-1411

Telnet Authentication: Kerberos Version 4

RFC-1412

Telnet Authentication: SPX

RFC-1571

Telnet Environment Option Interoperability Issues

RFC-1572

Telnet Environment Option

BUGS

Some TELNET commands are only partially implemented.

Because of bugs in the original 4.2 BSD telnet(1), in.telnetd performs some dubious protocol exchanges to try to discover if the remote client is, in fact, a 4.2 BSD telnet(1).

Binary mode has no common interpretation except between similar operating systems (Unix in this case).

The terminal type name received from the remote client is converted to lower case.

in.telnetd never sends TELNET IAC GA (go ahead) commands.

WONT CRYPT in.telnetd talks over insecure, unencrypted communications channels. Please use sshd(8) instead.