Rechercher une page de manuel
busybox
Langue: en
Version: 2009-03-27 (ubuntu - 07/07/09)
Section: 1 (Commandes utilisateur)
Sommaire
NAME
BusyBox - The Swiss Army Knife of Embedded LinuxSYNTAX
BusyBox <function> [arguments...] # or <function> [arguments...] # if symlinked
DESCRIPTION
BusyBox combines tiny versions of many common UNIX utilities into a single small executable. It provides minimalist replacements for most of the utilities you usually find in GNU coreutils, util-linux, etc. The utilities in BusyBox generally have fewer options than their full-featured GNU cousins; however, the options that are included provide the expected functionality and behave very much like their GNU counterparts.BusyBox has been written with size-optimization and limited resources in mind. It is also extremely modular so you can easily include or exclude commands (or features) at compile time. This makes it easy to customize your embedded systems. To create a working system, just add /dev, /etc, and a Linux kernel. BusyBox provides a fairly complete POSIX environment for any small or embedded system.
BusyBox is extremely configurable. This allows you to include only the components you need, thereby reducing binary size. Run 'make config' or 'make menuconfig' to select the functionality that you wish to enable. Then run 'make' to compile BusyBox using your configuration.
After the compile has finished, you should use 'make install' to install BusyBox. This will install the 'bin/busybox' binary, in the target directory specified by CONFIG_PREFIX. CONFIG_PREFIX can be set when configuring BusyBox, or you can specify an alternative location at install time (i.e., with a command line like 'make CONFIG_PREFIX=/tmp/foo install'). If you enabled any applet installation scheme (either as symlinks or hardlinks), these will also be installed in the location pointed to by CONFIG_PREFIX.
USAGE
BusyBox is a multi-call binary. A multi-call binary is an executable program that performs the same job as more than one utility program. That means there is just a single BusyBox binary, but that single binary acts like a large number of utilities. This allows BusyBox to be smaller since all the built-in utility programs (we call them applets) can share code for many common operations.You can also invoke BusyBox by issuing a command as an argument on the command line. For example, entering
/bin/busybox ls
will also cause BusyBox to behave as 'ls'.
Of course, adding '/bin/busybox' into every command would be painful. So most people will invoke BusyBox using links to the BusyBox binary.
For example, entering
ln -s /bin/busybox ls ./ls
will cause BusyBox to behave as 'ls' (if the 'ls' command has been compiled into BusyBox). Generally speaking, you should never need to make all these links yourself, as the BusyBox build system will do this for you when you run the 'make install' command.
If you invoke BusyBox with no arguments, it will provide you with a list of the applets that have been compiled into your BusyBox binary.
COMMON OPTIONS
Most BusyBox commands support the --help argument to provide a terse runtime description of their behavior. If the CONFIG_FEATURE_VERBOSE_USAGE option has been enabled, more detailed usage information will also be available.COMMANDS
Currently defined functions include:[, [[, addgroup, adduser, adjtimex, ar, arp, arping, ash, awk, basename, bbconfig, bbsh, brctl, bunzip2, busybox, bzcat, bzip2, cal, cat, catv, chat, chattr, chcon, chgrp, chmod, chown, chpasswd, chpst, chroot, chrt, chvt, cksum, clear, cmp, comm, cp, cpio, crond, crontab, cryptpw, cut, date, dc, dd, deallocvt, delgroup, deluser, devfsd, df, dhcprelay, diff, dirname, dmesg, dnsd, dos2unix, dpkg, dpkg_deb, du, dumpkmap, dumpleases, e2fsck, echo, ed, eject, env, envdir, envuidgid, ether_wake, expand, expr, fakeidentd, false, fbset, fdflush, fdformat, fdisk, fetchmail, find, findfs, fold, free, freeramdisk, fsck, fsck_minix, ftpget, ftpput, fuser, getenforce, getopt, getsebool, getty, grep, gunzip, gzip, halt, hd, hdparm, head, hexdump, hostid, hostname, httpd, hwclock, id, ifconfig, ifdown, ifenslave, ifup, inetd, init, insmod, install, ip, ipaddr, ipcalc, ipcrm, ipcs, iplink, iproute, iprule, iptunnel, kbd_mode, kill, killall, killall5, klogd, lash, last, length, less, ln, load_policy, loadfont, loadkmap, logger, login, logname, logread, losetup, lpd, lpq, lpr, ls, lsattr, lsmod, lzmacat, makedevs, matchpathcon, md5sum, mdev, mesg, microcom, mkdir, mke2fs, mkfifo, mkfs_minix, mknod, mkswap, mktemp, modprobe, more, mount, mountpoint, mt, mv, nameif, nc, netstat, nice, nmeter, nohup, nslookup, od, openvt, passwd, patch, pgrep, pidof, ping, ping6, pivot_root, pkill, poweroff, printenv, printf, ps, pscan, pwd, raidautorun, rdate, readahead, readlink, readprofile, realpath, reboot, renice, reset, resize, restorecon, rm, rmdir, rmmod, route, rpm, rpm2cpio, rtcwake, run_parts, runcon, runlevel, runsv, runsvdir, rx, script, sed, selinuxenabled, sendmail, seq, sestatus, setarch, setconsole, setenforce, setfiles, setkeycodes, setlogcons, setsebool, setsid, setuidgid, sha1sum, slattach, sleep, softlimit, sort, split, start_stop_daemon, stat, strings, stty, su, sulogin, sum, sv, svlogd, swapoff, swapon, switch_root, sync, sysctl, syslogd, tac, tail, tar, taskset, tcpsvd, tee, telnet, telnetd, test, tftp, tftpd, time, top, touch, tr, traceroute, true, tty, ttysize, tune2fs, udhcpc, udhcpd, udpsvd, umount, uname, uncompress, unexpand, uniq, unix2dos, unlzma, unzip, uptime, usleep, uudecode, uuencode, vconfig, vi, vlock, watch, watchdog, wc, wget, which, who, whoami, xargs, yes, zcat, zcip
COMMAND DESCRIPTIONS
- addgroup
- addgroup [-g GID] [user_name] group_name
Add a group or add an user to a group
Options:
-g GID Group id
- adduser
- adduser [OPTIONS] user_name
Add an user
Options:
-h DIR Home directory -g GECOS GECOS field -s SHELL Login shell -G GROUP Add user to existing group -S Create a system user -D Do not assign a password -H Do not create home directory
- adjtimex
- adjtimex [-q] [-o offset] [-f frequency] [-p timeconstant] [-t tick]
Read and optionally set system timebase parameters. See adjtimex(2).
Options:
-q Quiet -o offset Time offset, microseconds -f frequency Frequency adjust, integer kernel units (65536 is 1ppm) (positive values make clock run faster) -t tick Microseconds per tick, usually 10000 -p timeconstant
- ar
- ar [-o] [-v] [-p] [-t] [-x] ARCHIVE FILES
Extract or list FILES from an ar archive
Options:
-o Preserve original dates -p Extract to stdout -t List -x Extract -v Verbose
- arp
- arp [-vn] [-H type] [-i if] -a [hostname]
[-v] [-i if] -d hostname [pub]
[-v] [-H type] [-i if] -s hostname hw_addr [temp]
[-v] [-H type] [-i if] -s hostname hw_addr [netmask nm] pub
[-v] [-H type] [-i if] -Ds hostname ifa [netmask nm] pub
Manipulate ARP cache
Options:
-a Display (all) hosts -s Set new ARP entry -d Delete a specified entry -v Verbose -n Don't resolve names -i IF Network interface -D Read <hwaddr> from given device -A, -p AF Protocol family -H HWTYPE Hardware address type
- arping
- arping [-fqbDUA] [-c count] [-w timeout] [-I dev] [-s sender] target
Send ARP requests/replies
Options:
-f Quit on first ARP reply -q Quiet -b Keep broadcasting, don't go unicast -D Duplicated address detection mode -U Unsolicited ARP mode, update your neighbors -A ARP answer mode, update your neighbors -c N Stop after sending N ARP requests -w timeout Time to wait for ARP reply, in seconds -I dev Interface to use (default eth0) -s sender Sender IP address target Target IP address
- ash
- ash [FILE]... or: ash -c command [args]...
The ash shell
- awk
- awk [OPTION]... [program-text] [FILE...]
Options:
-v var=val Set variable -F sep Use sep as field separator -f file Read program from file
- basename
- basename FILE [SUFFIX]
Strip directory path and suffixes from FILE. If specified, also remove any trailing SUFFIX.
Example:
$ basename /usr/local/bin/foo foo $ basename /usr/local/bin/ bin $ basename /foo/bar.txt .txt bar
- bbconfig
- bbconfig
Print the config file which built busybox
- bbsh
- bbsh [FILE]... or: bbsh -c command [args]...
The bbsh shell (command interpreter)
- brctl
- brctl COMMAND [BRIDGE [INTERFACE]]
Manage ethernet bridges.
Commands:
addbr BRIDGE Create BRIDGE delbr BRIDGE Delete BRIDGE addif BRIDGE IFACE Add IFACE to BRIDGE delif BRIDGE IFACE Delete IFACE from BRIDGE setageing BRIDGE TIME Set ageing time setfd BRIDGE TIME Set bridge forward delay sethello BRIDGE TIME Set hello time setmaxage BRIDGE TIME Set max message age setpathcost BRIDGE COST Set path cost setportprio BRIDGE PRIO Set port priority setbridgeprio BRIDGE PRIO Set bridge priority stp BRIDGE [1|0] STP on/off
- bunzip2
- bunzip2 [OPTION]... [FILE]
Uncompress FILE (or standard input if FILE is '-' or omitted)
Options:
-c Write to standard output -f Force
- busybox
- busybox
Hello world!
- bzcat
- bzcat FILE
Uncompress to stdout
- bzip2
- bzip2 [OPTION]... [FILE]...
Compress FILE(s) with bzip2 algorithm. When FILE is '-' or unspecified, reads standard input. Implies -c.
Options:
-c Write to standard output -d Decompress -f Force -1..-9 Compression level
- cal
- cal [-jy] [[month] year]
Display a calendar
Options:
-j Use julian dates -y Display the entire year
- cat
- cat [-u] [FILE]...
Concatenate FILE(s) and print them to stdout
Options:
-u Use unbuffered i/o (ignored)
Example:
$ cat /proc/uptime 110716.72 17.67
- catv
- catv [-etv] [FILE]...
Display nonprinting characters as ^x or M-x
Options:
-e End each line with $ -t Show tabs as ^I -v Don't use ^x or M-x escapes
- chat
- chat EXPECT [SEND [EXPECT [SEND...]]]
Useful for interacting with a modem connected to stdin/stdout. A script consists of one or more ``expect-send'' pairs of strings, each pair is a pair of arguments. Example: chat '' ATZ OK ATD123456 CONNECT '' ogin: pppuser word: ppppass '~'
- chattr
- chattr [-R] [-+=AacDdijsStTu] [-v version] files...
Change file attributes on an ext2 fs
Modifiers:
- Remove attributes + Add attributes = Set attributes Attributes: A Don't track atime a Append mode only c Enable compress D Write dir contents synchronously d Do not backup with dump i Cannot be modified (immutable) j Write all data to journal first s Zero disk storage when deleted S Write file contents synchronously t Disable tail-merging of partial blocks with other files u Allow file to be undeleted Options: -R Recursively list subdirectories -v Set the file's version/generation number
- chcon
- chcon [OPTIONS] CONTEXT FILE... chcon [OPTIONS] [-u USER] [-r ROLE] [-l RANGE] [-t TYPE] FILE...
chcon [OPTIONS] --reference=RFILE FILE...
Change the security context of each FILE to CONTEXT
-v,--verbose Verbose -c,--changes Report changes made -h,--no-dereference Affect symlinks instead of their targets -f,--silent,--quiet Suppress most error messages --reference=RFILE Use RFILE's group instead of using a CONTEXT value -u,--user=USER Set user/role/type/range in the target -r,--role=ROLE security context -t,--type=TYPE -l,--range=RANGE -R,--recursive Recurse subdirectories
- chgrp
- chgrp [-RhLHPcvf]... GROUP FILE...
Change the group membership of each FILE to GROUP
Options:
-R Recurse directories -h Affect symlinks instead of symlink targets -L Traverse all symlinks to directories -H Traverse symlinks on command line only -P Do not traverse symlinks (default) -c List changed files -v Verbose -f Hide errors
Example:
$ ls -l /tmp/foo -r--r--r-- 1 andersen andersen 0 Apr 12 18:25 /tmp/foo $ chgrp root /tmp/foo $ ls -l /tmp/foo -r--r--r-- 1 andersen root 0 Apr 12 18:25 /tmp/foo
- chmod
- chmod [-Rcvf] MODE[,MODE]... FILE...
Each MODE is one or more of the letters ugoa, one of the symbols +-= and one or more of the letters rwxst
Options:
-R Recurse directories -c List changed files -v List all files -f Hide errors
Example:
$ ls -l /tmp/foo -rw-rw-r-- 1 root root 0 Apr 12 18:25 /tmp/foo $ chmod u+x /tmp/foo $ ls -l /tmp/foo -rwxrw-r-- 1 root root 0 Apr 12 18:25 /tmp/foo* $ chmod 444 /tmp/foo $ ls -l /tmp/foo -r--r--r-- 1 root root 0 Apr 12 18:25 /tmp/foo
- chown
- chown [-RhLHPcvf]... OWNER[<.|:>[GROUP]] FILE...
Change the owner and/or group of each FILE to OWNER and/or GROUP
Options:
-R Recurse directories -h Affect symlinks instead of symlink targets -L Traverse all symlinks to directories -H Traverse symlinks on command line only -P Do not traverse symlinks (default) -c List changed files -v List all files -f Hide errors
Example:
$ ls -l /tmp/foo -r--r--r-- 1 andersen andersen 0 Apr 12 18:25 /tmp/foo $ chown root /tmp/foo $ ls -l /tmp/foo -r--r--r-- 1 root andersen 0 Apr 12 18:25 /tmp/foo $ chown root.root /tmp/foo ls -l /tmp/foo -r--r--r-- 1 root root 0 Apr 12 18:25 /tmp/foo
- chpasswd
- chpasswd [--md5|--encrypt]
Read user:password information from stdin and update /etc/passwd accordingly.
Options:
-e,--encrypt Supplied passwords are in encrypted form -m,--md5 Use MD5 encryption instead of DES
- chpst
- chpst [-vP012] [-u user[:group]] [-U user[:group]] [-e dir] [-/ dir] [-n nice] [-m bytes] [-d bytes] [-o files] [-p processes] [-f bytes] [-c bytes] prog args
Change the process state and run specified program
Options:
-u USER[:GRP] Set uid and gid -U USER[:GRP] Set $UID and $GID in environment -e DIR Set environment variables as specified by files in DIR: file=1st_line_of_file -/ DIR Chroot to DIR -n INC Add INC to nice value -m BYTES Limit data segment, stack segment, locked physical pages, and total of all segment per process to BYTES each -d BYTES Limit data segment -o N Limit the number of open file descriptors per process to N -p N Limit number of processes per uid to N -f BYTES Limit output file size to BYTES -c BYTES Limit core file size to BYTES -v Verbose -P Run prog in a new process group -0 Close standard input -1 Close standard output -2 Close standard error
- chroot
- chroot NEWROOT [COMMAND...]
Run COMMAND with root directory set to NEWROOT
Example:
$ ls -l /bin/ls lrwxrwxrwx 1 root root 12 Apr 13 00:46 /bin/ls -> /BusyBox # mount /dev/hdc1 /mnt -t minix # chroot /mnt # ls -l /bin/ls -rwxr-xr-x 1 root root 40816 Feb 5 07:45 /bin/ls*
- chrt
- chrt [OPTION]... [prio] [pid | command [arg]...]
Manipulate real-time attributes of a process
Options:
-p Operate on pid -r Set scheduling policy to SCHED_RR -f Set scheduling policy to SCHED_FIFO -o Set scheduling policy to SCHED_OTHER -m Show min and max priorities
Example:
$ chrt -r 4 sleep 900; x=$! $ chrt -f -p 3 $x You need CAP_SYS_NICE privileges to set scheduling attributes of a process
- chvt
- chvt N
Change the foreground virtual terminal to /dev/ttyN
- cksum
- cksum FILES...
Calculate the CRC32 checksums of FILES
- clear
- clear
Clear screen
- cmp
- cmp [-l] [-s] FILE1 [FILE2 [SKIP1 [SKIP2]]]
Compares FILE1 vs stdin if FILE2 is not specified
Options:
-l Write the byte numbers (decimal) and values (octal) for all differing bytes -s Quiet
- comm
- comm [-123] FILE1 FILE2
Compare FILE1 to FILE2, or to stdin if - is specified
Options:
-1 Suppress lines unique to FILE1 -2 Suppress lines unique to FILE2 -3 Suppress lines common to both files
- cp
- cp [OPTION]... SOURCE DEST
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY
Options:
-a Same as -dpR -c Preserve security context -d,-P Preserve links -H,-L Dereference all symlinks (default) -p Preserve file attributes if possible -f Force overwrite -i Prompt before overwrite -R,-r Recurse directories -l,-s Create (sym)links
- cpio
- cpio -[dimtuv][F cpiofile]
Extract or list files from a cpio archive Main operation mode:
d Make leading directories i Extract m Preserve mtime t List v Verbose u Unconditional overwrite F Input from file
- crond
- crond -fbS -l N -d N -L LOGFILE -c DIR
-f Foreground -b Background (default) -S Log to syslog (default) -l Set log level. 0 is the most verbose, default 8 -d Set log level, log to stderr -L Log to file -c Working dir
- crontab
- crontab [-c DIR] [-u USER] [-ler]|[FILE]
-c Crontab directory -u User -l List crontab -e Edit crontab -r Delete crontab FILE Replace crontab by FILE ('-': stdin)
- cryptpw
- cryptpw [-a des|md5] [string]
Output crypted string. If string isn't supplied on cmdline, read it from stdin.
Options:
-a Algorithm to use (default: md5)
- cut
- cut [OPTION]... [FILE]...
Print selected fields from each input FILE to standard output
Options:
-b LIST Output only bytes from LIST -c LIST Output only characters from LIST -d CHAR Use CHAR instead of tab as the field delimiter -s Output only the lines containing delimiter -f N Print only these fields -n Ignored
Example:
$ echo "Hello world" | cut -f 1 -d ' ' Hello $ echo "Hello world" | cut -f 2 -d ' ' world
- date
- date [OPTION]... [MMDDhhmm[[CC]YY][.ss]] [+FORMAT]
Display current time in the given FORMAT, or set system date
Options:
-R Output RFC-822 compliant date string -d STRING Display time described by STRING, not 'now' -I[TIMESPEC] Output an ISO-8601 compliant date/time string TIMESPEC='date' (or missing) for date only, 'hours', 'minutes', or 'seconds' for date and time to the indicated precision -D hint Use 'hint' as date format, via strptime() -s STRING Set time described by STRING -r FILE Display the last modification time of FILE -u Print or sets Coordinated Universal Time
Example:
$ date Wed Apr 12 18:52:41 MDT 2000
- dc
- dc expression...
This is a Tiny RPN calculator that understands the following operations: +, add, -, sub, *, mul, /, div, %, mod, **, exp, and, or, not, eor. For example: 'dc 2 2 add' -> 4, and 'dc 8 8 \* 2 2 + /' -> 16.
Options: p - Print the value on the top of the stack, without altering the stack f - Print the entire contents of the stack without altering anything o - Pop the value off the top of the stack and use it to set the output radix
Only 10 and 16 are supported
Example:
$ dc 2 2 + p 4 $ dc 8 8 \* 2 2 + / p 16 $ dc 0 1 and p 0 $ dc 0 1 or p 1 $ echo 72 9 div 8 mul p | dc 64
- dd
- dd [if=FILE] [of=FILE] [ibs=N] [obs=N] [bs=N] [count=N] [skip=N] [seek=N] [conv=notrunc|noerror|sync]
Copy a file with converting and formatting
Options:
if=FILE Read from FILE instead of stdin of=FILE Write to FILE instead of stdout bs=N Read and write N bytes at a time ibs=N Read N bytes at a time obs=N Write N bytes at a time count=N Copy only N input blocks skip=N Skip N input blocks seek=N Skip N output blocks conv=notrunc Don't truncate output file conv=noerror Continue after read errors conv=sync Pad blocks with zeros
Numbers may be suffixed by c (x1), w (x2), b (x512), kD (x1000), k (x1024), MD (x1000000), M (x1048576), GD (x1000000000) or G (x1073741824)
Example:
$ dd if=/dev/zero of=/dev/ram1 bs=1M count=4 4+0 records in 4+0 records out
- deallocvt
- deallocvt [N]
Deallocate unused virtual terminal /dev/ttyN
- delgroup
- delgroup [USER] GROUP
Delete group GROUP from the system or user USER from group GROUP
- deluser
- deluser USER
Delete user USER from the system
- devfsd
- devfsd mntpnt [-v][-fg][-np]
Manage devfs permissions and old device name symlinks
Options:
mntpnt The mount point where devfs is mounted -v Print the protocol version numbers for devfsd and the kernel-side protocol version and exit -fg Run in foreground -np Exit after parsing the configuration file and processing synthetic REGISTER events, do not poll for events
- df
- df DF_HAS_OPTIONS(``[-'') hmki DF_HAS_OPTIONS(``] '') "[FILESYSTEM...]
Print filesystem usage statistics
DF_HAS_OPTIONS(" Options:") -h Human readable (e.g. 1K 243M 2G) -m 1024*1024 blocks -k 1024 blocks -i Inodes
Example:
$ df Filesystem 1k-blocks Used Available Use% Mounted on /dev/sda3 8690864 8553540 137324 98% / /dev/sda1 64216 36364 27852 57% /boot $ df /dev/sda3 Filesystem 1k-blocks Used Available Use% Mounted on /dev/sda3 8690864 8553540 137324 98% /
- dhcprelay
- dhcprelay [client_device_list] [server_device]
Relay dhcp requests from client devices to server device
- diff
- diff [-abdiNqrTstw] [-L LABEL] [-S FILE] [-U LINES] FILE1 FILE2
Compare files line by line and output the differences between them. This implementation supports unified diffs only.
Options:
-a Treat all files as text -b Ignore changes in the amount of whitespace -d Try hard to find a smaller set of changes -i Ignore case differences -L Use LABEL instead of the filename in the unified header -N Treat absent files as empty -q Output only whether files differ -r Recursively compare subdirectories -S Start with FILE when comparing directories -T Make tabs line up by prefixing a tab when necessary -s Report when two files are the same -t Expand tabs to spaces in output -U Output LINES lines of context -w Ignore all whitespace
- dirname
- dirname FILENAME
Strip non-directory suffix from FILENAME
Example:
$ dirname /tmp/foo /tmp $ dirname /tmp/foo/ /tmp
- dmesg
- dmesg [-c] [-n LEVEL] [-s SIZE]
Print or control the kernel ring buffer
Options:
-c Clear ring buffer after printing -n LEVEL Set console logging level -s SIZE Buffer size
- dnsd
- dnsd [-c config] [-t seconds] [-p port] [-i iface-ip] [-d]
Small static DNS server daemon
Options:
-c Config filename -t TTL in seconds -p Listening port -i Listening ip (default all) -d Daemonize
- dos2unix
- dos2unix [option] [FILE]
Convert FILE from dos to unix format. When no file is given, use stdin/stdout.
Options:
-u dos2unix -d unix2dos
- dpkg
- dpkg [-ilCPru] [-F option] package_name
Install, remove and manage Debian packages
Options:
-i Install the package -l List of installed packages -C Configure an unpackaged package -F depends Ignore dependency problems -P Purge all files of a package -r Remove all but the configuration files for a package -u Unpack a package, but don't configure it
- dpkg-deb
- dpkg-deb [-cefxX] FILE [argument]
Perform actions on Debian packages (.debs)
Options:
-c List contents of filesystem tree -e Extract control files to [argument] directory -f Display control field name starting with [argument] -x Extract packages filesystem tree to directory -X Verbose extract
Example:
$ dpkg-deb -X ./busybox_0.48-1_i386.deb /tmp
- du
- du [-aHLdclsxhmk] [FILE]...
Summarize disk space used for each FILE and/or directory. Disk space is printed in units of 1024 bytes.
Options:
-a Show file sizes too -H Follow symlinks on command line -L Follow all symlinks -d N Limit output to directories (and files with -a) of depth < N -c Show grand total -l Count sizes many times if hard linked -s Display only a total for each argument -x Skip directories on different filesystems -h Sizes in human readable format (e.g., 1K 243M 2G ) -m Sizes in megabytes -k Sizes in kilobytes (default)
Example:
$ du 16 ./CVS 12 ./kernel-patches/CVS 80 ./kernel-patches 12 ./tests/CVS 36 ./tests 12 ./scripts/CVS 16 ./scripts 12 ./docs/CVS 104 ./docs 2417 .
- dumpkmap
- dumpkmap
Print out a binary keyboard translation table to standard output
Example:
$ dumpkmap > keymap
- dumpleases
- dumpleases [-r|-a] [-f LEASEFILE]
Display DHCP leases granted by udhcpd
Options:
-f,--file=FILE Leases file to load -r,--remaining Interpret lease times as time remaining -a,--absolute Interpret lease times as expire time
- e2fsck
- e2fsck [-panyrcdfvstDFSV] [-b superblock] [-B blocksize] [-I inode_buffer_blocks] [-P process_inode_size] [-l|-L bad_blocks_file] [-C fd] [-j external_journal] [-E extended-options] device
Check ext2/ext3 file system
Options:
-p Automatic repair (no questions) -n Make no changes to the filesystem -y Assume 'yes' to all questions -c Check for bad blocks and add them to the badblock list -f Force checking even if filesystem is marked clean -v Verbose -b superblock Use alternative superblock -B blocksize Force blocksize when looking for superblock -j journal Set location of the external journal -l file Add to badblocks list -L file Set badblocks list
- echo
- echo [-neE] [ARG...]
Print the specified ARGs to stdout
Options:
-n Suppress trailing newline -e Interpret backslash-escaped characters (i.e., \t=tab) -E Disable interpretation of backslash-escaped characters
Example:
$ echo "Erik is cool" Erik is cool $ echo -e "Erik\nis\ncool" Erik is cool $ echo "Erik\nis\ncool" Erik\nis\ncool
- ed
- ed #define ed_full_usage
- eject
- eject [-t] [-T] [DEVICE]
Eject specified DEVICE (or default /dev/cdrom)
Options:
-s SCSI device -t Close tray -T Open/close tray (toggle)
- env
- env [-iu] [-] [name=value]... [command]
Print the current environment or run a program after setting up the specified environment
Options:
-, -i Start with an empty environment -u Remove variable from the environment
- envdir
- envdir dir prog args
Set various environment variables as specified by files in the directory dir, then run prog
- envuidgid
- envuidgid account prog args
Set $UID to account's uid and $GID to account's gid, then run prog
- ether_wake
- ether_wake [-b] [-i iface] [-p aa:bb:cc:dd[:ee:ff]] MAC
Send a magic packet to wake up sleeping machines. MAC must be a station address (00:11:22:33:44:55) or a hostname with a known 'ethers' entry.
Options:
-b Send wake-up packet to the broadcast address -i iface Interface to use (default eth0) -p pass Append four or six byte password PW to the packet
- expand
- expand [-i] [-t NUM] [FILE|-]
Convert tabs to spaces, writing to standard output.
Options:
-i,--initial Do not convert tabs after non blanks -t,--tabs=N Tabstops every N chars
- expr
- expr EXPRESSION
Print the value of EXPRESSION to standard output.
EXPRESSION may be:
ARG1 | ARG2 ARG1 if it is neither null nor 0, otherwise ARG2 ARG1 & ARG2 ARG1 if neither argument is null or 0, otherwise 0 ARG1 < ARG2 1 if ARG1 is less than ARG2, else 0. Similarly: ARG1 <= ARG2 ARG1 = ARG2 ARG1 != ARG2 ARG1 >= ARG2 ARG1 > ARG2 ARG1 + ARG2 Sum of ARG1 and ARG2. Similarly: ARG1 - ARG2 ARG1 * ARG2 ARG1 / ARG2 ARG1 % ARG2 STRING : REGEXP Anchored pattern match of REGEXP in STRING match STRING REGEXP Same as STRING : REGEXP substr STRING POS LENGTH Substring of STRING, POS counted from 1 index STRING CHARS Index in STRING where any CHARS is found, or 0 length STRING Length of STRING quote TOKEN Interpret TOKEN as a string, even if it is a keyword like 'match' or an operator like '/' (EXPRESSION) Value of EXPRESSION
Beware that many operators need to be escaped or quoted for shells. Comparisons are arithmetic if both ARGs are numbers, else lexicographical. Pattern matches return the string matched between \( and \) or null; if \( and \) are not used, they return the number of characters matched or 0.
- fakeidentd
- fakeidentd [-fiw] [-b ADDR] [STRING]
Provide fake ident (auth) service
Options:
-f Run in foreground -i Inetd mode -w Inetd 'wait' mode -b ADDR Bind to specified address STRING Ident answer string (default is 'nobody')
- false
- false
Return an exit code of FALSE (1)
Example:
$ false $ echo $? 1
- fbset
- fbset [options] [mode]
Show and modify frame buffer settings
Example:
$ fbset mode "1024x768-76" # D: 78.653 MHz, H: 59.949 kHz, V: 75.694 Hz geometry 1024 768 1024 768 16 timings 12714 128 32 16 4 128 4 accel false rgba 5/11,6/5,5/0,0/0 endmode
- fdflush
- fdflush DEVICE
Force floppy disk drive to detect disk change
- fdformat
- fdformat [-n] DEVICE
Format floppy disk
Options:
-n Don't verify after format
- fdisk
- fdisk [-uls] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK
Change partition table
Options:
-u Start and End are in sectors (instead of cylinders) -l Show partition table for each DISK, then exit -s Show partition sizes in kb for each DISK, then exit -b 2048 (for certain MO disks) use 2048-byte sectors -C CYLINDERS Set number of cylinders/heads/sectors -H HEADS -S SECTORS
- fetchmail
- fetchmail [-w timeout] [-U user] -P password [-X] [-t] [-z] server[:port] maildir [prog]
Fetch content of remote mailbox to local Maildir.
Options:
-w timeout Set timeout on network operations -U username Authenticate with specified username/password -P password -X Use openssl connection helper for secured servers -t Get only headers -z Delete messages on server prog Run prog <message_file> on message delivery
- find
- find [PATH...] [EXPRESSION]
Search for files. The default PATH is the current directory, default EXPRESSION is '-print'
EXPRESSION may consist of:
-follow Dereference symlinks -xdev Don't descend directories on other filesystems -maxdepth N Descend at most N levels. -maxdepth 0 applies tests/actions to command line arguments only -name PATTERN File name (w/o directory name) matches PATTERN -iname PATTERN Case insensitive -name -path PATTERN Path matches PATTERN -regex PATTERN Path matches regex PATTERN -type X File type is X (X is one of: f,d,l,b,c,...) -perm NNN Permissions match any of (+NNN), all of (-NNN), or exactly (NNN) -mtime DAYS Modified time is greater than (+N), less than (-N), or exactly (N) days -mmin MINS Modified time is greater than (+N), less than (-N), or exactly (N) minutes -newer FILE Modified time is more recent than FILE's -inum N File has inode number N -user NAME File is owned by user NAME (numeric user ID allowed) -group NAME File belongs to group NAME (numeric group ID allowed) -depth Process directory name after traversing it -size N[bck] File size is N (c:bytes,k:kbytes,b:512 bytes(def.)). +/-N: file size is bigger/smaller than N -print Print (default and assumed) -print0 Delimit output with null characters rather than newlines USE_FEATURE_FIND_CONTEXT ( -context File has specified security context") -exec CMD ARG ; Execute CMD with all instances of {} replaced by the matching files -prune Stop traversing current subtree -delete Delete files, turns on -depth option (EXPR) Group an expression
Example:
$ find / -name passwd /etc/passwd
- findfs
- findfs LABEL=label or UUID=uuid
Find a filesystem device based on a label or UUID.
Example:
$ findfs LABEL=MyDevice
- fold
- fold [-bs] [-w WIDTH] [FILE]
Wrap input lines in each FILE (standard input by default), writing to standard output
Options:
-b Count bytes rather than columns -s Break at spaces -w Use WIDTH columns instead of 80
- free
- free
Display the amount of free and used system memory
Example:
$ free total used free shared buffers Mem: 257628 248724 8904 59644 93124 Swap: 128516 8404 120112 Total: 386144 257128 129016
- freeramdisk
- freeramdisk DEVICE
Free all memory used by the specified ramdisk
Example:
$ freeramdisk /dev/ram2
- fsck
- fsck [-ANPRTV] [-C fd] [-t fstype] [fs-options] [filesys...]
Check and repair filesystems
Options:
-A Walk /etc/fstab and check all filesystems -N Don't execute, just show what would be done -P With -A, check filesystems in parallel -R With -A, skip the root filesystem -T Don't show title on startup -V Verbose -C n Write status information to specified filedescriptor -t type List of filesystem types to check
- fsck.minix
- fsck.minix [-larvsmf] /dev/name
Perform a consistency check for MINIX filesystems
Options:
-l List all filenames -r Perform interactive repairs -a Perform automatic repairs -v Verbose -s Output super-block information -m Activate MINIX-like "mode not cleared" warnings -f Force file system check
- ftpget
- ftpget [options] remote-host local-file remote-file
Retrieve a remote file via FTP
Options:
-c,--continue Continue previous transfer -v,--verbose Verbose -u,--username Username -p,--password Password -P,--port Port number
- ftpput
- ftpput [options] remote-host remote-file local-file
Store a local file on a remote machine via FTP
Options:
-v,--verbose Verbose -u,--username Username -p,--password Password -P,--port Port number
- fuser
- fuser [options] FILE or PORT/PROTO
Find processes which use FILEs or PORTs
Options:
-m Find processes which use same fs as FILEs -4 Search only IPv4 space -6 Search only IPv6 space -s Silent: just exit with 0 if any processes are found -k Kill found processes (otherwise display PIDs) -SIGNAL Signal to send (default: TERM)
- getenforce
- getenforce #define getenforce_full_usage
- getopt
- getopt [OPTIONS]...
Parse command options
-a,--alternative Allow long options starting with single - -l,--longoptions=longopts Long options to be recognized -n,--name=progname The name under which errors are reported -o,--options=optstring Short options to be recognized -q,--quiet Disable error reporting by getopt(3) -Q,--quiet-output No normal output -s,--shell=shell Set shell quoting conventions -T,--test Test for getopt(1) version -u,--unquoted Don't quote the output
Example:
$ cat getopt.test #!/bin/sh GETOPT=`getopt -o ab:c:: --long a-long,b-long:,c-long:: \ -n 'example.busybox' -- "$@"` if [ $? != 0 ]; then exit 1; fi eval set -- "$GETOPT" while true; do case $1 in -a|--a-long) echo "Option a"; shift;; -b|--b-long) echo "Option b, argument '$2'"; shift 2;; -c|--c-long) case "$2" in "") echo "Option c, no argument"; shift 2;; *) echo "Option c, argument '$2'"; shift 2;; esac;; --) shift; break;; *) echo "Internal error!"; exit 1;; esac done
- getsebool
- getsebool -a or getsebool boolean...
-a Show all SELinux booleans
- getty
- getty [OPTIONS] BAUD_RATE TTY [TERMTYPE]
Open a tty, prompt for a login name, then invoke /bin/login
Options:
-h Enable hardware (RTS/CTS) flow control -i Do not display /etc/issue before running login -L Local line, do not do carrier detect -m Get baud rate from modem's CONNECT status message -w Wait for a CR or LF before sending /etc/issue -n Do not prompt the user for a login name -f issue_file Display issue_file instead of /etc/issue -l login_app Invoke login_app instead of /bin/login -t timeout Terminate after timeout if no username is read -I initstring Init string to send before anything else -H login_host Log login_host into the utmp file as the hostname
- grep
- grep [-HhrilLnqvsoweFEABC] PATTERN [FILEs...]
Search for PATTERN in each FILE or standard input
Options:
-H Prefix output lines with filename where match was found -h Suppress the prefixing filename on output -r Recurse subdirectories -i Ignore case distinctions -l List names of files that match -L List names of files that do not match -n Print line number with output lines -q Quiet. Return 0 if PATTERN is found, 1 otherwise -v Select non-matching lines -s Suppress file open/read error messages -c Only print count of matching lines -o Show only the part of a line that matches PATTERN -m MAX Match up to MAX times per file -w Match whole words only -F PATTERN is a set of newline-separated strings -E PATTERN is an extended regular expression -e PTRN Pattern to match -f FILE Read pattern from file -A Print NUM lines of trailing context -B Print NUM lines of leading context -C Print NUM lines of output context
Example:
$ grep root /etc/passwd root:x:0:0:root:/root:/bin/bash $ grep ^[rR]oo. /etc/passwd root:x:0:0:root:/root:/bin/bash
- gunzip
- gunzip [OPTION]... [FILE]...
Uncompress FILEs (or standard input)
Options:
-c Write to standard output -f Force -t Test file integrity
Example:
$ ls -la /tmp/BusyBox* -rw-rw-r-- 1 andersen andersen 557009 Apr 11 10:55 /tmp/BusyBox-0.43.tar.gz $ gunzip /tmp/BusyBox-0.43.tar.gz $ ls -la /tmp/BusyBox* -rw-rw-r-- 1 andersen andersen 1761280 Apr 14 17:47 /tmp/BusyBox-0.43.tar
- gzip
- gzip [OPTION]... [FILE]...
Compress FILEs (or standard input)
Options:
-c Write to standard output -d Decompress -f Force
Example:
$ ls -la /tmp/busybox* -rw-rw-r-- 1 andersen andersen 1761280 Apr 14 17:47 /tmp/busybox.tar $ gzip /tmp/busybox.tar $ ls -la /tmp/busybox* -rw-rw-r-- 1 andersen andersen 554058 Apr 14 17:49 /tmp/busybox.tar.gz
- halt
- halt [-d delay] [-n] [-f]
Halt the system
Options:
-d Delay interval for halting -n No call to sync() -f Force halt (don't go through init) -w Only write a wtmp record
- hd
- hd FILE...
hd is an alias for hexdump -C
- hdparm
- hdparm [options] [device] ..
Options:
-a Get/set fs readahead -A Set drive read-lookahead flag (0/1) -b Get/set bus state (0 == off, 1 == on, 2 == tristate) -B Set Advanced Power Management setting (1-255) -c Get/set IDE 32-bit IO setting -C Check IDE power mode status -d Get/set using_dma flag -D Enable/disable drive defect-mgmt -f Flush buffer cache for device on exit -g Display drive geometry -h Display terse usage information -i Display drive identification -I Detailed/current information directly from drive -k Get/set keep_settings_over_reset flag (0/1) -K Set drive keep_features_over_reset flag (0/1) -L Set drive doorlock (0/1) (removable harddisks only) -m Get/set multiple sector count -n Get/set ignore-write-errors flag (0/1) -p Set PIO mode on IDE interface chipset (0,1,2,3,4,...) -P Set drive prefetch count/* " -q Change next setting quietly" - not supported ib bbox */ -Q Get/set DMA tagged-queuing depth (if supported) -r Get/set readonly flag (DANGEROUS to set) -R Register an IDE interface (DANGEROUS) -S Set standby (spindown) timeout -t Perform device read timings -T Perform cache read timings -u Get/set unmaskirq flag (0/1) -U Un-register an IDE interface (DANGEROUS) -v Defaults; same as -mcudkrag for IDE drives -V Display program version and exit immediately -w Perform device reset (DANGEROUS) -W Set drive write-caching flag (0/1) (DANGEROUS) -x Tristate device for hotswap (0/1) (DANGEROUS) -X Set IDE xfer mode (DANGEROUS) -y Put IDE drive in standby mode -Y Put IDE drive to sleep -Z Disable Seagate auto-powersaving mode -z Re-read partition table
- head
- head [OPTION]... [FILE]...
Print first 10 lines of each FILE to standard output. With more than one FILE, precede each with a header giving the file name. With no FILE, or when FILE is -, read standard input.
Options:
-n NUM Print first NUM lines instead of first 10 -c NUM Output the first NUM bytes -q Never output headers giving file names -v Always output headers giving file names
Example:
$ head -n 2 /etc/passwd root:x:0:0:root:/root:/bin/bash daemon:x:1:1:daemon:/usr/sbin:/bin/sh
- hexdump
- hexdump [-bcCdefnosvxR] FILE...
Display file(s) or standard input in a user specified format
Options:
-b One-byte octal display -c One-byte character display -C Canonical hex+ASCII, 16 bytes per line -d Two-byte decimal display -e FORMAT STRING -f FORMAT FILE -n LENGTH Interpret only LENGTH bytes of input -o Two-byte octal display -s OFFSET Skip OFFSET bytes -v Display all input data -x Two-byte hexadecimal display -R Reverse of 'hexdump -Cv'
- hostid
- hostid
Print out a unique 32-bit identifier for the machine
- hostname
- hostname [OPTION] [hostname | -F FILE]
Get or set hostname or DNS domain name
Options:
-s Short -i Addresses for the hostname -d DNS domain name -f Fully qualified domain name -F FILE Use the contents of FILE to specify the hostname
Example:
$ hostname sage
- httpd
- httpd [-c conffile] [-p [ip:]port] [-i] [-f] [-v[v]] [-u user[:grp]] [-r realm] [-m pass] [-h home] [-d/-e string]
Listen for incoming HTTP requests
Options:
-c FILE Configuration file (default httpd.conf) -p [IP:]PORT Bind to ip:port (default *:80) -i Inetd mode -f Do not daemonize -v[v] Verbose -u USER[:GRP] Set uid/gid after binding to port -r REALM Authentication Realm for Basic Authentication -m PASS Crypt PASS with md5 algorithm -h HOME Home directory (default .) -e STRING HTML encode STRING -d STRING URL decode STRING
- hwclock
- hwclock [-r|--show] [-s|--hctosys] [-w|--systohc] [-l|--localtime] [-u|--utc] [-f FILE]
Query and set hardware clock (RTC)
Options:
-r Show time from hardware clock -s Set system time from hardware clock -w Set hardware clock to system time -u Hardware clock is in UTC -l Hardware clock is in local time -f FILE Use specified device (e.g. /dev/rtc2)
- id
- id [OPTIONS]... [USER]
Print information about USER or the current user
Options:
-Z Print the security context -g Print group ID -u Print user ID -n Print name instead of a number -r Print real user ID instead of effective ID
Example:
$ id uid=1000(andersen) gid=1000(andersen)
- ifconfig
- ifconfig [-a] interface [address]
Configure a network interface
Options:
[add ADDRESS[/PREFIXLEN]] [del ADDRESS[/PREFIXLEN]] [[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]] [netmask ADDRESS] [dstaddr ADDRESS] [outfill NN] [keepalive NN] [hw ether ADDRESS] [metric NN] [mtu NN] [[-]trailers] [[-]arp] [[-]allmulti] [multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic] [mem_start NN] [io_addr NN] [irq NN] [up|down] ...
- ifdown
- ifdown [-ainmvf] ifaces...
Options:
-a De/configure all interfaces automatically -i FILE Use FILE for interface definitions -n Print out what would happen, but don't do it (note: doesn't disable mappings) -m Don't run any mappings -v Print out what would happen before doing it -f Force de/configuration
- ifenslave
- ifenslave [-cdf] master-iface <slave-iface...>
Configure network interfaces for parallel routing
Options:
-c, --change-active Change active slave -d, --detach Remove slave interface from bonding device -f, --force Force, even if interface is not Ethernet/* " -r, --receive-slave Create a receive-only slave" */
Example:
To create a bond device, simply follow these three steps : - ensure that the required drivers are properly loaded : # modprobe bonding ; modprobe <3c59x|eepro100|pcnet32|tulip|...> - assign an IP address to the bond device : # ifconfig bond0 <addr> netmask <mask> broadcast <bcast> - attach all the interfaces you need to the bond device : # ifenslave bond0 eth0 eth1 eth2 If bond0 didn't have a MAC address, it will take eth0's. Then, all interfaces attached AFTER this assignment will get the same MAC addr. To detach a dead interface without setting the bond device down : # ifenslave -d bond0 eth1 To set the bond device down and automatically release all the slaves : # ifconfig bond0 down To change active slave : # ifenslave -c bond0 eth0
- ifup
- ifup [-ainmvf] ifaces...
Options:
-a De/configure all interfaces automatically -i FILE Use FILE for interface definitions -n Print out what would happen, but don't do it (note: doesn't disable mappings) -m Don't run any mappings -v Print out what would happen before doing it -f Force de/configuration
- inetd
- inetd [-fe] [-q N] [-R N] [CONFFILE]
Listen for network connections and launch programs
Options:
-f Run in foreground -e Log to stderr -q N Socket listen queue (default: 128) -R N Pause services after N connects/min (default: 0 - disabled)
- init
- init
Init is the parent of all processes
This version of init is designed to be run only by the kernel.
BusyBox init doesn't support multiple runlevels. The runlevels field of the /etc/inittab file is completely ignored by BusyBox init. If you want runlevels, use sysvinit.
BusyBox init works just fine without an inittab. If no inittab is found, it has the following default behavior:
::sysinit:/etc/init.d/rcS ::askfirst:/bin/sh ::ctrlaltdel:/sbin/reboot ::shutdown:/sbin/swapoff -a ::shutdown:/bin/umount -a -r ::restart:/sbin/init
if it detects that /dev/console is _not_ a serial console, it will also run:
tty2::askfirst:/bin/sh tty3::askfirst:/bin/sh tty4::askfirst:/bin/sh
If you choose to use an /etc/inittab file, the inittab entry format is as follows:
<id>:<runlevels>:<action>:<process> <id>: WARNING: This field has a non-traditional meaning for BusyBox init! The id field is used by BusyBox init to specify the controlling tty for the specified process to run on. The contents of this field are appended to "/dev/" and used as-is. There is no need for this field to be unique, although if it isn't you may have strange results. If this field is left blank, the controlling tty is set to the console. Also note that if BusyBox detects that a serial console is in use, then only entries whose controlling tty is either the serial console or /dev/null will be run. BusyBox init does nothing with utmp. We don't need no stinkin' utmp. <runlevels>: The runlevels field is completely ignored. <action>: Valid actions include: sysinit, respawn, askfirst, wait, once, restart, ctrlaltdel, and shutdown. The available actions can be classified into two groups: actions that are run only once, and actions that are re-run when the specified process exits. Run only-once actions: 'sysinit' is the first item run on boot. init waits until all sysinit actions are completed before continuing. Following the completion of all sysinit actions, all 'wait' actions are run. 'wait' actions, like 'sysinit' actions, cause init to wait until the specified task completes. 'once' actions are asynchronous, therefore, init does not wait for them to complete. 'restart' is the action taken to restart the init process. By default this should simply run /sbin/init, but can be a script which runs pivot_root or it can do all sorts of other interesting things. The 'ctrlaltdel' init actions are run when the system detects that someone on the system console has pressed the CTRL-ALT-DEL key combination. Typically one wants to run 'reboot' at this point to cause the system to reboot. Finally the 'shutdown' action specifies the actions to taken when init is told to reboot. Unmounting filesystems and disabling swap is a very good here. Run repeatedly actions: 'respawn' actions are run after the 'once' actions. When a process started with a 'respawn' action exits, init automatically restarts it. Unlike sysvinit, BusyBox init does not stop processes from respawning out of control. The 'askfirst' actions acts just like respawn, except that before running the specified process it displays the line "Please press Enter to activate this console." and then waits for the user to press enter before starting the specified process. Unrecognized actions (like initdefault) will cause init to emit an error message, and then go along with its business. All actions are run in the order they appear in /etc/inittab. <process>: Specifies the process to be executed and its command line.
Example /etc/inittab file:
# This is run first except when booting in single-user mode # ::sysinit:/etc/init.d/rcS # /bin/sh invocations on selected ttys # # Start an "askfirst" shell on the console (whatever that may be) ::askfirst:-/bin/sh # Start an "askfirst" shell on /dev/tty2-4 tty2::askfirst:-/bin/sh tty3::askfirst:-/bin/sh tty4::askfirst:-/bin/sh # /sbin/getty invocations for selected ttys # tty4::respawn:/sbin/getty 38400 tty4 tty5::respawn:/sbin/getty 38400 tty5 # Example of how to put a getty on a serial line (for a terminal) # #::respawn:/sbin/getty -L ttyS0 9600 vt100 #::respawn:/sbin/getty -L ttyS1 9600 vt100 # # Example how to put a getty on a modem line #::respawn:/sbin/getty 57600 ttyS2 # Stuff to do when restarting the init process ::restart:/sbin/init # Stuff to do before rebooting ::ctrlaltdel:/sbin/reboot ::shutdown:/bin/umount -a -r ::shutdown:/sbin/swapoff -a
- insmod
- insmod [OPTION]... MODULE [symbol=value]...
Load the specified kernel modules into the kernel
Options:
-f Force module to load into the wrong kernel version -k Make module autoclean-able -v Verbose -q Quiet -L Lock to prevent simultaneous loads of a module -m Output load map to stdout -o NAME Set internal module name to NAME -x Do not export externs
- install
- install [-cgmops] [sources] dest|directory
Copy files and set attributes
Options:
-c Copy the file, default -d Create directories -g Set group ownership -m Set permissions -o Set ownership -p Preserve date -s Strip symbol tables -Z Set security context of copy
- ip
- ip [OPTIONS] {address | route | link | tunnel | rule} {COMMAND}
ip [OPTIONS] OBJECT {COMMAND} where OBJECT := {address | route | link | tunnel | rule} OPTIONS := { -f[amily] { inet | inet6 | link } | -o[neline] }
- ipaddr
- ipaddr { {add|del} IFADDR dev STRING | {show|flush} [dev STRING] [to PREFIX] }
ipaddr {add|delete} IFADDR dev STRING ipaddr {show|flush} [dev STRING] [scope SCOPE-ID]
[to PREFIX] [label PATTERN] IFADDR := PREFIX | ADDR peer PREFIX [broadcast ADDR] [anycast ADDR] [label STRING] [scope SCOPE-ID] SCOPE-ID := [host | link | global | NUMBER]
- ipcalc
- ipcalc [OPTION]... ADDRESS[[/]NETMASK] [NETMASK]
Calculate IP network settings from a IP address
Options:
-b,--broadcast Display calculated broadcast address -n,--network Display calculated network address -m,--netmask Display default netmask for IP -p,--prefix Display the prefix for IP/NETMASK -h,--hostname Display first resolved host name -s,--silent Don't ever display error messages )
- ipcrm
- ipcrm [-MQS key] [-mqs id]
Upper-case options MQS remove an object by shmkey value. Lower-case options remove an object by shmid value.
Options:
-mM Remove memory segment after last detach -qQ Remove message queue -sS Remove semaphore
- ipcs
- ipcs [[-smq] -i shmid] | [[-asmq] [-tcplu]]
-i Show specific resource Resource specification: -m Shared memory segments -q Message queues -s Semaphore arrays -a All (default) Output format: -t Time -c Creator -p Pid -l Limits -u Summary
- iplink
- iplink
iplink set DEVICE { up | down | arp | multicast { on | off } |
dynamic { on | off } | mtu MTU } iplink show [DEVICE]
- iproute
- iproute { list | flush | { add | del | change | append | replace | monitor } ROUTE }
iproute { list | flush } SELECTOR iproute get ADDRESS [from ADDRESS iif STRING]
[oif STRING] [tos TOS] iproute { add | del | change | append | replace | monitor } ROUTE SELECTOR := [root PREFIX] [match PREFIX] [proto RTPROTO] ROUTE := [TYPE] PREFIX [tos TOS] [proto RTPROTO]
- iprule
- iprule {[list | add | del] RULE}
iprule [list | add | del] SELECTOR ACTION
SELECTOR := [from PREFIX] [to PREFIX] [tos TOS] [fwmark FWMARK] [dev STRING] [pref NUMBER] ACTION := [table TABLE_ID] [nat ADDRESS] [prohibit | reject | unreachable] [realms [SRCREALM/]DSTREALM] TABLE_ID := [local | main | default | NUMBER]
- iptunnel
- iptunnel { add | change | del | show } [NAME] [mode { ipip | gre | sit }]
[remote ADDR] [local ADDR] [ttl TTL]
iptunnel { add | change | del | show } [NAME]
[mode { ipip | gre | sit }] [remote ADDR] [local ADDR] [[i|o]seq] [[i|o]key KEY] [[i|o]csum] [ttl TTL] [tos TOS] [[no]pmtudisc] [dev PHYS_DEV]
- kbd_mode
- kbd_mode [-a|k|s|u]
Report or set the keyboard mode
Options set mode:
-a Default (ASCII) -k Medium-raw (keyboard) -s Raw (scancode) -u Unicode (utf-8)
- kill
- kill [-l] [-signal] process-id...
Send a signal (default is TERM) to the specified process(es)
Options:
-l List all signal names and numbers
Example:
$ ps | grep apache 252 root root S [apache] 263 www-data www-data S [apache] 264 www-data www-data S [apache] 265 www-data www-data S [apache] 266 www-data www-data S [apache] 267 www-data www-data S [apache] $ kill 252
- killall
- killall [-l] [-q] [-signal] process-name...
Send a signal (default is TERM) to the specified process(es)
Options:
-l List all signal names and numbers -q Do not complain if no processes were killed
Example:
$ killall apache
- killall5
- killall5 [-l] [-signal]
Send a signal (default is TERM) to all processes outside current session
Options:
-l List all signal names and numbers
- klogd
- klogd [-c n] [-n]
Kernel logger
Options:
-c n Set the default log level of console messages to n -n Run in foreground
- lash
- lash [FILE]... or: sh -c command [args]...
lash is deprecated, please use hush
- last
- last
Show listing of the last users that logged into the system
- length
- length STRING
Print STRING's length
Example:
$ length Hello 5
- less
- less [-EMNmh~?] [FILE...]
View a file or list of files. The position within files can be changed, and files can be manipulated in various ways.
Options:
-E Quit once the end of a file is reached -M,-m Display a status line containing the line numbers and percentage through the file -N Prefix line numbers to each line -~ Suppress ~s displayed past the end of the file
- ln
- ln [OPTION] TARGET... LINK_NAME|DIRECTORY
Create a link named LINK_NAME or DIRECTORY to the specified TARGET. Use '--' to indicate that all following arguments are non-options.
Options:
-s Make symlinks instead of hardlinks -f Remove existing destination files -n Don't dereference symlinks - treat like normal file -b Make a backup of the target (if exists) before link operation -S suf Use suffix instead of ~ when making backup files
Example:
$ ln -s BusyBox /tmp/ls $ ls -l /tmp/ls lrwxrwxrwx 1 root root 7 Apr 12 18:39 ls -> BusyBox*
- load_policy
- load_policy
- loadfont
- loadfont < font
Load a console font from standard input
Example:
$ loadfont < /etc/i18n/fontname
- loadkmap
- loadkmap < keymap
Load a binary keyboard translation table from standard input
Example:
$ loadkmap < /etc/i18n/lang-keymap
- logger
- logger [OPTION]... [MESSAGE]
Write MESSAGE to the system log. If MESSAGE is omitted, log stdin.
Options:
-s Log to stderr as well as the system log -t TAG Log using the specified tag (defaults to user name) -p PRIO Priority (numeric or facility.level pair)
Example:
$ logger "hello"
- login
- login [-p] [-h HOST] [[-f] USER]
Begin a new session on the system
Options:
-f Do not authenticate (user already authenticated) -h Name of the remote host -p Preserve environment
- logname
- logname
Print the name of the current user
Example:
$ logname root
- logread
- logread [OPTION]...
Show messages in syslogd's circular buffer
Options:
-f Output data as log grows
- losetup
- losetup [-o OFS] LOOPDEV FILE - associate loop devices losetup -d LOOPDEV - disassociate
losetup [-f] - show
Options:
-o OFS Start OFS bytes into FILE -f Show first free loop device
No arguments will display all current associations. One argument (losetup /dev/loop1) will display the current association (if any), or disassociate it (with -d). The display shows the offset and filename of the file the loop device is currently bound to.
Two arguments (losetup /dev/loop1 file.img) create a new association, with an optional offset (-o 12345). Encryption is not yet supported. losetup -f will show the first loop free loop device
- lpd
- lpd SPOOLDIR
Example:
tcpsvd -E 0 515 softlimit -m 99999 lpd /var/spool
- lpq
- lpq
Options:
-P lp service to connect to (else uses $PRINTER) -d Delete jobs -f Force any waiting job to be printed -s Short display
- lpr
- lpr
Options:
-P lp service to connect to (else uses $PRINTER) -m Send mail on completion -h Print banner page too -V Verbose
- ls
- ls [-1AacCdeFilnpLRrSsTtuvwxXhkK] [filenames...]
List directory contents
Options:
-1 List files in a single column -A Do not list implied . and .. -a Do not hide entries starting with . -C List entries by columns -c With -l: show ctime --color[={always,never,auto}] Control coloring -d List directory entries instead of contents -e List both full date and full time -F Append indicator (one of */=@|) to entries -i List the i-node for each file -l Use a long listing format -n List numeric UIDs and GIDs instead of names -p Append indicator (one of /=@|) to entries -L List entries pointed to by symlinks -R List subdirectories recursively -r Sort the listing in reverse order -S Sort the listing by file size -s List the size of each file, in blocks -T NUM Assume Tabstop every NUM columns -t With -l: show modification time -u With -l: show access time -v Sort the listing by version -w NUM Assume the terminal is NUM columns wide -x List entries by lines instead of by columns -X Sort the listing by extension -h Print sizes in human readable format (e.g., 1K 243M 2G) -k Print security context -K Print security context in long format -Z Print security context and permission
- lsattr
- lsattr [-Radlv] [files...]
List file attributes on an ext2 fs
Options:
-R Recursively list subdirectories -a Do not hide entries starting with . -d List directory entries instead of contents -l Print long flag names -v List the file's version/generation number
- lsmod
- lsmod
List the currently loaded kernel modules
- lzmacat
- lzmacat FILE
Uncompress to stdout
- makedevs
- makedevs [-d device_table] rootdir
Create a range of special files as specified in a device table. Device table entries take the form of: <type> <mode> <uid> <gid> <major> <minor> <start> <inc> <count> Where name is the file name, type can be one of:
f A regular file d Directory c Character special device file b Block special device file p Fifo (named pipe) uid is the user id for the target file, gid is the group id for the target file. The rest of the entries (major, minor, etc) apply to to device special files. A '-' may be used for blank entries.
Example:
For example: <name> <type> <mode><uid><gid><major><minor><start><inc><count> /dev d 755 0 0 - - - - - /dev/console c 666 0 0 5 1 - - - /dev/null c 666 0 0 1 3 0 0 - /dev/zero c 666 0 0 1 5 0 0 - /dev/hda b 640 0 0 3 0 0 0 - /dev/hda b 640 0 0 3 1 1 1 15 Will Produce: /dev /dev/console /dev/null /dev/zero /dev/hda /dev/hda[0-15]
- matchpathcon
- matchpathcon [-n] [-N] [-f file_contexts_file] [-p prefix] [-V]
-n Do not display path -N Do not use translations -f Use alternate file_context file -p Use prefix to speed translations -V Verify file context on disk matches defaults
- md5sum
- md5sum [OPTION] [FILEs...]
or: md5sum [OPTION] -c [FILE]Print or check MD5 checksums
Options:
-c Check MD5 sums against given list -s Don't output anything, status code shows success -w Warn about improperly formatted MD5 checksum lines
Example:
$ md5sum < busybox 6fd11e98b98a58f64ff3398d7b324003 $ md5sum busybox 6fd11e98b98a58f64ff3398d7b324003 busybox $ md5sum -c - 6fd11e98b98a58f64ff3398d7b324003 busybox busybox: OK ^D
- mdev
- mdev [-s]
-s Scan /sys and populate /dev during system boot
Called with no options (via hotplug) it uses environment variables to determine which device to add/remove.
The mdev config file contains lines that look like: hd[a-z][0-9]* 0:3 660
That's device name (with regex match), uid:gid, and permissions.
Optionally, that can be followed (on the same line) by a special character and a command line to run after creating/before deleting the corresponding device(s). The environment variable $MDEV indicates the active device node (which is useful if it's a regex match). For example:
hdc root:cdrom 660 *ln -s $MDEV cdrom
The special characters are @ (run after creating), $ (run before deleting), and * (run both after creating and before deleting). The commands run in the /dev directory, and use system() which calls /bin/sh.
Config file parsing stops on the first matching line. If no config entry is matched, devices are created with default 0:0 660. (Make the last line match .* to override this.)
- mesg
- mesg [y|n]
Control write access to your terminal
y Allow write access to your terminal n Disallow write access to your terminal
- microcom
- microcom [-d DELAY] [-t TIMEOUT] [-s SPEED] [-X] TTY
Copy bytes for stdin to TTY and from TTY to stdout
Options:
-d Wait up to DELAY ms for TTY output before sending every next byte to it -t Exit if both stdin and TTY are silent for TIMEOUT ms -s Set serial line to SPEED -X Disable special meaning of NUL and Ctrl-X from stdin
- mkdir
- mkdir [OPTION] DIRECTORY...
Create DIRECTORY
Options:
-m Set permission mode (as in chmod), not rwxrwxrwx - umask -p No error if existing, make parent directories as needed -Z Set security context
Example:
$ mkdir /tmp/foo $ mkdir /tmp/foo /tmp/foo: File exists $ mkdir /tmp/foo/bar/baz /tmp/foo/bar/baz: No such file or directory $ mkdir -p /tmp/foo/bar/baz
- mke2fs
- mke2fs [-c|-l filename] [-b block-size] [-f fragment-size] [-g blocks-per-group] [-i bytes-per-inode] [-j] [-J journal-options] [-N number-of-inodes] [-n] [-m reserved-blocks-percentage] [-o creator-os] [-O feature[,...]] [-q] [r fs-revision-level] [-E extended-options] [-v] [-F] [-L volume-label] [-M last-mounted-directory] [-S] [-T filesystem-type] device [blocks-count]
-b size Block size in bytes -c Check for bad blocks before creating -E opts Set extended options -f size Fragment size in bytes -F Force (ignore sanity checks) -g num Number of blocks in a block group -i ratio The bytes/inode ratio -j Create a journal (ext3) -J opts Set journal options (size/device) -l file Read bad blocks list from file -L lbl Set the volume label -m percent Percent of fs blocks to reserve for admin -M dir Set last mounted directory -n Do not actually create anything -N num Number of inodes to create -o os Set the 'creator os' field -O features Dir_index/filetype/has_journal/journal_dev/sparse_super -q Quiet -r rev Set filesystem revision -S Write superblock and group descriptors only -T fs-type Set usage type (news/largefile/largefile4) -v Verbose
- mkfifo
- mkfifo [OPTIONS] name
Create named pipe (identical to 'mknod name p')
Options:
-m MODE Mode (default a=rw) -Z Set security context
- mkfs.minix
- mkfs.minix [-c | -l filename] [-nXX] [-iXX] /dev/name [blocks]
Make a MINIX filesystem
Options:
-c Check device for bad blocks -n [14|30] Maximum length of filenames -i INODES Number of inodes for the filesystem -l FILENAME Read bad blocks list from FILENAME -v Make version 2 filesystem
- mknod
- mknod [OPTIONS] NAME TYPE MAJOR MINOR
Create a special file (block, character, or pipe)
Options:
-m Create the special file using the specified mode (default a=rw) TYPEs include: b: Make a block device c or u: Make a character device p: Make a named pipe (MAJOR and MINOR are ignored) -Z Set security context
Example:
$ mknod /dev/fd0 b 2 0 $ mknod -m 644 /tmp/pipe p
- mkswap
- mkswap DEVICE
Prepare block device to be used as swap partition
- mktemp
- mktemp [-dt] [-p DIR] TEMPLATE
Create a temporary file with its name based on TEMPLATE. TEMPLATE is any name with six 'Xs' (i.e., /tmp/temp.XXXXXX).
Options:
-d Make a directory instead of a file/* " -q Fail silently if an error occurs" - we ignore it */ -t Generate a path rooted in temporary directory -p DIR Use DIR as a temporary directory (implies -t)
For -t or -p, directory is chosen as follows: $TMPDIR if set, else -p DIR, else /tmp
Example:
$ mktemp /tmp/temp.XXXXXX /tmp/temp.mWiLjM $ ls -la /tmp/temp.mWiLjM -rw------- 1 andersen andersen 0 Apr 25 17:10 /tmp/temp.mWiLjM
- modprobe
- modprobe [-knqrsv] MODULE [symbol=value...]
Options:
-k Make module autoclean-able -n Dry run -q Quiet -r Remove module (stacks) or do autoclean -s Report via syslog instead of stderr -v Verbose
modprobe can (un)load a stack of modules, passing each module options (when loading). modprobe uses a configuration file to determine what option(s) to pass each module it loads.
The configuration file is searched (in order) amongst:
/etc/modprobe.conf (2.6 only) /etc/modules.conf /etc/conf.modules (deprecated)
They all have the same syntax (see below). If none is present, it is _not_ an error; each loaded module is then expected to load without options. Once a file is found, the others are tested for.
/etc/modules.conf entry format:
alias <alias_name> <mod_name> Makes it possible to modprobe alias_name, when there is no such module. It makes sense if your mod_name is long, or you want a more representative name for that module (eg. 'scsi' in place of 'aha7xxx'). This makes it also possible to use a different set of options (below) for the module and the alias. A module can be aliased more than once. options <mod_name|alias_name> <symbol=value...> When loading module mod_name (or the module aliased by alias_name), pass the "symbol=value" pairs as option to that module.
Sample /etc/modules.conf file:
options tulip irq=3 alias tulip tulip2 options tulip2 irq=4 io=0x308
Other functionality offered by 'classic' modprobe is not available in this implementation.
If module options are present both in the config file, and on the command line, then the options from the command line will be passed to the module _after_ the options from the config file. That way, you can have defaults in the config file, and override them for a specific usage from the command line.
Example:
(with the above /etc/modules.conf): $ modprobe tulip will load the module 'tulip' with default option 'irq=3' $ modprobe tulip irq=5 will load the module 'tulip' with option 'irq=5', thus overriding the default $ modprobe tulip2 will load the module 'tulip' with default options 'irq=4 io=0x308', which are the default for alias 'tulip2' $ modprobe tulip2 irq=8 will load the module 'tulip' with default options 'irq=4 io=0x308 irq=8', which are the default for alias 'tulip2' overridden by the option 'irq=8' from the command line $ modprobe tulip2 irq=2 io=0x210 will load the module 'tulip' with default options 'irq=4 io=0x308 irq=4 io=0x210', which are the default for alias 'tulip2' overridden by the options 'irq=2 io=0x210' from the command line
- more
- more [FILE...]
View FILE or standard input one screenful at a time
Example:
$ dmesg | more
- mount
- mount [flags] DEVICE NODE [-o options,more-options]
Mount a filesystem. Filesystem autodetection requires /proc be mounted.
Options:
-a Mount all filesystems in fstab -f Update /etc/mtab, but don't mount -i Don't call /sbin/mount.<filesystem> helper -n Don't update /etc/mtab -r Read-only mount -t fs-type Filesystem type -w Read-write mount (default) B<-o> option: loop Ignored (loop devices are autodetected) [a]sync Writes are asynchronous / synchronous [no]atime Disable / enable updates to inode access times [no]diratime Disable / enable atime updates to directories [no]dev Allow use of special device files / disallow them [no]exec Allow use of executable files / disallow them [no]suid Allow set-user-id-root programs / disallow them [r]shared Convert [recursively] to a shared subtree [r]slave Convert [recursively] to a slave subtree [r]private Convert [recursively] to a private subtree [un]bindable Make mount point [un]able to be bind mounted bind Bind a directory to an additional location move Relocate an existing mount point remount Remount a mounted filesystem, changing its flags ro/rw Mount for read-only / read-write
There are EVEN MORE flags that are specific to each filesystem You'll have to see the written documentation for those filesystems
Returns 0 for success, number of failed mounts for -a, or errno for one mount.
Example:
$ mount /dev/hda3 on / type minix (rw) proc on /proc type proc (rw) devpts on /dev/pts type devpts (rw) $ mount /dev/fd0 /mnt -t msdos -o ro $ mount /tmp/diskimage /opt -t ext2 -o loop $ mount cd_image.iso mydir
- mountpoint
- mountpoint [-q] <[-d] DIR | -x DEVICE>
mountpoint checks if the directory is a mountpoint
Options:
-q Quiet -d Print major/minor device number of the filesystem -x Print major/minor device number of the blockdevice
Example:
$ mountpoint /proc /proc is not a mountpoint $ mountpoint /sys /sys is a mountpoint
- mt
- mt [-f device] opcode value
Control magnetic tape drive operation
Available Opcodes:
bsf bsfm bsr bss datacompression drvbuffer eof eom erase fsf fsfm fsr fss load lock mkpart nop offline ras1 ras2 ras3 reset retension rewind rewoffline seek setblk setdensity setpart tell unload unlock weof wset
- mv
- mv [OPTION]... SOURCE DEST or: mv [OPTION]... SOURCE... DIRECTORY
Rename SOURCE to DEST, or move SOURCE(s) to DIRECTORY
Options:
-f Don't prompt before overwriting -i Interactive, prompt before overwrite
Example:
$ mv /tmp/foo /bin/bar
- nameif
- nameif [-s] [-c FILE] [{IFNAME MACADDR}]
Rename network interface while it in the down state
Options:
-c FILE Use configuration file (default is /etc/mactab) -s Use syslog (LOCAL0 facility) IFNAME MACADDR new_interface_name interface_mac_address
Example:
$ nameif -s dmz0 00:A0:C9:8C:F6:3F or $ nameif -c /etc/my_mactab_file
- nc
- nc [-options] hostname port - connect nc [-options] -l -p port [hostname] [port] - listen
Options:
-e prog [args] Program to exec after connect (must be last) -l Listen mode, for inbound connects -n Don't do DNS resolution -s addr Local address -p port Local port -u UDP mode -v Verbose (cumulative: -vv) -w secs Timeout for connects and final net reads -i sec Delay interval for lines sent" /* ", ports scanned" */ -o file Hex dump of traffic -z Zero-I/O mode (scanning)/* " -r Randomize local and remote ports" */ To use netcat as a terminal emulator on a serial port:
$ stty 115200 -F /dev/ttyS0 $ stty raw -echo -ctlecho && nc -f /dev/ttyS0
Example:
$ nc foobar.somedomain.com 25 220 foobar ESMTP Exim 3.12 #1 Sat, 15 Apr 2000 00:03:02 -0600 help 214-Commands supported: 214- HELO EHLO MAIL RCPT DATA AUTH 214 NOOP QUIT RSET HELP quit 221 foobar closing connection
- netstat
- netstat [-laentuwxrW]
Display networking information
Options:
-l Display listening server sockets -a Display all sockets (default: connected) -e Display other/more information -n Don't resolve names -t Tcp sockets -u Udp sockets -w Raw sockets -x Unix sockets -r Display routing table -W Display with no column truncation
- nice
- nice [-n ADJUST] [COMMAND [ARG]...]
Run a program with modified scheduling priority
Options:
-n ADJUST Adjust the scheduling priority by ADJUST
- nmeter
- nmeter format_string
Monitor system in real time
Format specifiers: %Nc or %[cN] Monitor CPU. N - bar size, default 10
(displays: S:system U:user N:niced D:iowait I:irq i:softirq) %[niface] Monitor network interface 'iface' %m Monitor allocated memory %[mf] Monitor free memory %[mt] Monitor total memory %s Monitor allocated swap %f Monitor number of used file descriptors %Ni Monitor total/specific IRQ rate %x Monitor context switch rate %p Monitor forks %[pn] Monitor # of processes %b Monitor block io %Nt Show time (with N decimal points) %Nd Milliseconds between updates (default=1000) %r Print <cr> instead of <lf> at EOL
Example:
nmeter '%250d%t %20c int %i bio %b mem %m forks%p'
- nohup
- nohup COMMAND [ARGS]
Run a command immune to hangups, with output to a non-tty
Example:
$ nohup make &
- nslookup
- nslookup [HOST] [SERVER]
Query the nameserver for the IP address of the given HOST optionally using a specified DNS server
Example:
$ nslookup localhost Server: default Address: default Name: debian Address: 127.0.0.1
- od
- od [-aBbcDdeFfHhIiLlOovXx] [-t TYPE] [FILE]
Write an unambiguous representation, octal bytes by default, of FILE to standard output. With no FILE or when FILE is -, read standard input.
- openvt
- openvt VTNUM COMMAND [ARGS...]
Start a command on a new virtual terminal
Example:
openvt 2 /bin/ash
- passwd
- passwd [OPTION] [name]
Change user's password. If no name is specified, changes the password for the current user.
Options:
-a Algorithm to use for password (choices: des, md5)" /* ", sha1)" */ -d Delete password for the account -l Lock (disable) account -u Unlock (re-enable) account
- patch
- patch [-p NUM] [-i DIFF]
-p NUM Strip NUM leading components from file names -i DIFF Read DIFF instead of stdin
Example:
$ patch -p1 < example.diff $ patch -p0 -i example.diff
- pgrep
- pgrep [-flnovx] pattern
Display process(es) selected by regex pattern
Options:
-l Show command name too -f Match against entire command line -n Show the newest process only -o Show the oldest process only -v Negate the matching -x Match whole name (not substring)
- pidof
- pidof [NAME...]
List PIDs of all processes with names that match NAMEs USAGE_PIDOF
-s Show only one PID -o PID Omit given pid Use %PPID to omit pid of pidof's parent
Example:
$ pidof init 1 $ pidof /bin/sh 20351 5973 5950 $ pidof /bin/sh -o %PPID 20351 5950
- ping
- ping [OPTION]... host
Send ICMP ECHO_REQUEST packets to network hosts
Options:
-4, -6 Force IPv4 or IPv6 hostname resolution -c CNT Send only CNT pings -s SIZE Send SIZE data bytes in packets (default=56) -I iface/IP Use interface or IP address as source -q Quiet, only displays output at start and when finished
Example:
$ ping localhost PING slag (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=20.1 ms --- debian ping statistics --- 1 packets transmitted, 1 packets received, 0% packet loss round-trip min/avg/max = 20.1/20.1/20.1 ms
- ping6
- ping6 [OPTION]... host
Send ICMP ECHO_REQUEST packets to network hosts
Options:
-c CNT Send only CNT pings -s SIZE Send SIZE data bytes in packets (default=56) -I iface/IP Use interface or IP address as source -q Quiet, only displays output at start and when finished
Example:
$ ping6 ip6-localhost PING ip6-localhost (::1): 56 data bytes 64 bytes from ::1: icmp6_seq=0 ttl=64 time=20.1 ms --- ip6-localhost ping statistics --- 1 packets transmitted, 1 packets received, 0% packet loss round-trip min/avg/max = 20.1/20.1/20.1 ms
- pivot_root
- pivot_root NEW_ROOT PUT_OLD
Move the current root file system to PUT_OLD and make NEW_ROOT the new root file system
- pkill
- pkill [-l] | [-fnovx] [-signal] pattern
Send a signal to process(es) selected by regex pattern
Options:
-l List all signals -f Match against entire command line -n Signal the newest process only -o Signal the oldest process only -v Negate the matching -x Match whole name (not substring)
- poweroff
- poweroff [-d delay] [-n] [-f]
Halt and shut off power
Options:
-d Delay interval for halting -n No call to sync() -f Force power off (don't go through init)
- printenv
- printenv [VARIABLES...]
Print all or part of environment. If no environment VARIABLE specified, print them all.
- printf
- printf FORMAT [ARGUMENT...]
Format and print ARGUMENT(s) according to FORMAT, where FORMAT controls the output exactly as in C printf
Example:
$ printf "Val=%d\n" 5 Val=5
- ps
- ps
Report process status
USAGE_PS -Z Show SE Linux context w Wide output
Example:
$ ps PID Uid Gid State Command 1 root root S init 2 root root S [kflushd] 3 root root S [kupdate] 4 root root S [kpiod] 5 root root S [kswapd] 742 andersen andersen S [bash] 743 andersen andersen S -bash 745 root root S [getty] 2990 andersen andersen R ps
- pscan
- pscan [-p MIN_PORT] [-P MAX_PORT] [-t TIMEOUT] [-T MIN_RTT] HOST
Scan a host, print all open ports
Options:
-p Scan from this port (default 1) -P Scan up to this port (default 1024) -t Timeout (default 5000 ms) -T Minimum rtt (default 5 ms, increase for congested hosts)
- pwd
- pwd
Print the full filename of the current working directory
Example:
$ pwd /root
- raidautorun
- raidautorun DEVICE
Tell the kernel to automatically search and start RAID arrays
Example:
$ raidautorun /dev/md0
- rdate
- rdate [-sp] HOST
Get and possibly set the system date and time from a remote HOST
Options:
-s Set the system date and time (default) -p Print the date and time
- readahead
- readahead [FILE]...
Preload FILE(s) in RAM cache so that subsequent reads for thosefiles do not block on disk I/O
- readlink
- readlink [-f] FILE
Display the value of a symlink
Options:
-f Canonicalize by following all symlinks
- readprofile
- readprofile [OPTIONS]...
Options:
-m mapfile (Default: /boot/System.map) -p profile (Default: /proc/profile) -M mult Set the profiling multiplier to mult -i Print only info about the sampling step -v Verbose -a Print all symbols, even if count is 0 -b Print individual histogram-bin counts -s Print individual counters within functions -r Reset all the counters (root only) -n Disable byte order auto-detection
- realpath
- realpath pathname...
Return the absolute pathnames of given argument
- reboot
- reboot [-d delay] [-n] [-f]
Reboot the system
Options:
-d Delay interval for rebooting -n No call to sync() -f Force reboot (don't go through init)
- renice
- renice {{-n INCREMENT} | PRIORITY} [[-p | -g | -u] ID...]
Change priority of running processes
Options:
-n Adjust current nice value (smaller is faster) -p Process id(s) (default) -g Process group id(s) -u Process user name(s) and/or id(s)
- reset
- reset
Reset the screen
- resize
- resize
Resize the screen
- restorecon
- restorecon [-iFnrRv] [-e excludedir]... [-o filename] [-f filename | pathname]
Reset security contexts of files in pathname
-i Ignore files that do not exist -f file File with list of files to process. Use - for stdin -e directory Directory to exclude -R,-r Recurse directories -n Don't change any file labels -o file Save list of files with incorrect context -v Verbose -vv Show changed labels -F Force reset of context to match file_context for customizable files, or the user section, if it has changed
- rm
- rm [OPTION]... FILE...
Remove (unlink) the FILE(s). Use '--' to indicate that all following arguments are non-options.
Options:
-i Always prompt before removing -f Never prompt -r,-R Remove directories recursively
Example:
$ rm -rf /tmp/foo
- rmdir
- rmdir [OPTION]... DIRECTORY...
Remove the DIRECTORY, if it is empty
Example:
# rmdir /tmp/foo
- rmmod
- rmmod [OPTION]... [MODULE]...
Unload the specified kernel modules from the kernel
Options:
-a Remove all unused modules (recursively)
Example:
$ rmmod tulip
- route
- route [{add|del|delete}]
Edit the kernel's routing tables
Options:
-n Dont resolve names -e Display other/more information -A inet{6} Select address family
- rpm
- rpm -i -q[ildc]p package.rpm
Manipulate RPM packages
Options:
-i Install package -q Query package -p Query uninstalled package -i Show information -l List contents -d List documents -c List config files
- rpm2cpio
- rpm2cpio package.rpm
Output a cpio archive of the rpm file
- rtcwake
- rtcwake [-a | -l | -u] [-d DEV] [-m MODE] [-s SECS | -t TIME]
Enter a system sleep state until specified wakeup time
-a,--auto Read clock mode from adjtime -l,--local Clock is set to local time -u,--utc Clock is set to UTC time -d,--device=DEV Specify the RTC device -m,--mode=MODE Set the sleep state (default: standby) -s,--seconds=SEC Set the timeout in SEC seconds from now -t,--time=TIME Set the timeout to TIME seconds from epoch
- run-parts
- run-parts [-t] [-l] [-a ARG] [-u MASK] DIRECTORY
Run a bunch of scripts in a directory
Options:
-t Print what would be run, but don't actually run anything -a ARG Pass ARG as argument for every program -u MASK Set the umask to MASK before running every program -l Print names of all matching files even if they are not executable
Example:
$ run-parts -a start /etc/init.d $ run-parts -a stop=now /etc/init.d Let's assume you have a script foo/dosomething: #!/bin/sh for i in $*; do eval $i; done; unset i case "$1" in start*) echo starting something;; stop*) set -x; shutdown -h $stop;; esac Running this yields: $run-parts -a stop=+4m foo/ + shutdown -h +4m
- runcon
- runcon [-c] [-u USER] [-r ROLE] [-t TYPE] [-l RANGE] COMMAND [args] runcon CONTEXT COMMAND [args]
Run a program in a different security context
CONTEXT Complete security context -c,--compute Compute process transition context before modifying -t,--type=TYPE Type (for same role as parent) -u,--user=USER User identity -r,--role=ROLE Role -l,--range=RNG Levelrange
- runlevel
- runlevel [utmp]
Example:
$ runlevel /var/run/utmp N 2
- runsv
- runsv dir
Start and monitor a service and optionally an appendant log service
- runsvdir
- runsvdir [-P] dir
Start a runsv process for each subdirectory
- rx
- rx FILE
Receive a file using the xmodem protocol
Example:
$ rx /tmp/foo
- script
- script [-afq] [-c COMMAND] [OUTFILE]
Options:
-a Append output -c Run COMMAND, not shell -f Flush output after each write -q Quiet
- sed
- sed [-efinr] pattern [files...]
Options:
-e script Add the script to the commands to be executed -f scriptfile Add scriptfile contents to the commands to be executed -i Edit files in-place -n Suppress automatic printing of pattern space -r Use extended regular expression syntax
If no -e or -f is given, the first non-option argument is taken as the sed script to interpret. All remaining arguments are names of input files; if no input files are specified, then the standard input is read. Source files will not be modified unless -i option is given.
Example:
$ echo "foo" | sed -e 's/f[a-zA-Z]o/bar/g' bar
- selinuxenabled
- selinuxenabled #define selinuxenabled_full_usage
- sendmail
- sendmail [-w timeout] [-U user] [-P password] [-X] -t to [-t to]... [-n] [-s subject] [-c charset] server[:port] from [body] [attachment ...]
Send an email.
Options:
-w timeout Set timeout on network operations -U username Authenticate with specified username/password -P password -t address Recipient(s). May be repeated -X Use openssl connection helper for secured servers -n Request delivery notification to sender -s subject Subject -c charset Assumed charset for body and subject [utf-8]
- seq
- seq [first [increment]] last
Print numbers from FIRST to LAST, in steps of INCREMENT. FIRST, INCREMENT default to 1
Arguments:
LAST FIRST LAST FIRST INCREMENT LAST
- sestatus
- sestatus [-vb]
-v Verbose -b Display current state of booleans
- setarch
- setarch personality program [args...]
Personality may be:
linux32 Set 32bit uname emulation linux64 Set 64bit uname emulation
- setconsole
- setconsole [-r|--reset] [DEVICE]
Redirect system console output to DEVICE (default: /dev/tty)
Options:
-r Reset output to /dev/console
- setenforce
- setenforce [Enforcing | Permissive | 1 | 0]
- setfiles
- setfiles [-dnpqsvW] [-e dir]... [-o file] [-r alt_root_path] [-c policyfile] spec_file pathname
Reset file contexts under pathname according to spec_file
-c file Check the validity of the contexts against the specified binary policy -d Show which specification matched each file -l Log changes in file labels to syslog -n Don't change any file labels -q Suppress warnings -r dir Use an altenate root path -e dir Exclude directory -F Force reset of context to match file_context for customizable files -o file Save list of files with incorrect context -s Take a list of files from standard input (instead of command line) -v Show changes in file labels, if type or role are changing -vv Show changes in file labels, if type, role, or user are changing -W Display warnings about entries that had no matching files
- setkeycodes
- setkeycodes SCANCODE KEYCODE...
Set entries into the kernel's scancode-to-keycode map, allowing unusual keyboards to generate usable keycodes.
SCANCODE may be either xx or e0xx (hexadecimal), and KEYCODE is given in decimal
Example:
$ setkeycodes e030 127
- setlogcons
- setlogcons N
Redirect the kernel output to console N (0 for current)
- setsebool
- setsebool boolean value
Change boolean setting
- setsid
- setsid PROG [ARG...]
Run PROG in a new session. PROG will have no controlling terminal and will not be affected by keyboard signals (Ctrl-C etc). See setsid(2) for details.
- setuidgid
- setuidgid account prog args
Set uid and gid to account's uid and gid, removing all supplementary groups, then run prog
- sha1sum
- sha1sum [OPTION] [FILEs...]
or: sha1sum [OPTION] -c [FILE]Print or check SHA1 checksums.
Options:
-c Check SHA1 sums against given list -s Don't output anything, status code shows success -w Warn about improperly formatted SHA1 checksum lines
- slattach
- slattach [-cehmLF] [-s speed] [-p protocol] DEVICEs
Attach network interface(s) to serial line(s)
Options:
-p Set protocol (slip, cslip, slip6, clisp6 or adaptive) -s Set line speed -e Exit after initializing device -h Exit when the carrier is lost -c Execute a command when the line is hung up -m Do NOT initialize the line in raw 8 bits mode -L Enable 3-wire operation -F Disable RTS/CTS flow control
- sleep
- sleep [N]...
Pause for a time equal to the total of the args given, where each arg can have an optional suffix of (s)econds, (m)inutes, (h)ours, or (d)ays
Example:
$ sleep 2 [2 second delay results] $ sleep 1d 3h 22m 8s [98528 second delay results]
- softlimit
- softlimit [-a allbytes] [-c corebytes] [-d databytes] [-f filebytes] [-l lockbytes] [-m membytes] [-o openfiles] [-p processes] [-r residentbytes] [-s stackbytes] [-t cpusecs] prog args
Set soft resource limits, then run prog
Options:
-m n Same as -d n -s n -l n -a n -d n Limit the data segment per process to n bytes -s n Limit the stack segment per process to n bytes -l n Limit the locked physical pages per process to n bytes -a n Limit the total of all segments per process to n bytes -o n Limit the number of open file descriptors per process to n -p n Limit the number of processes per uid to n Options controlling file sizes: -f n Limit output file sizes to n bytes -c n Limit core file sizes to n bytes Efficiency opts: -r n Limit the resident set size to n bytes. This limit is not enforced unless physical memory is full -t n Limit the CPU time to n seconds. This limit is not enforced except that the process receives a SIGXCPU signal after n seconds
Some options may have no effect on some operating systems n may be =, indicating that soft limit should be set equal to hard limit
- sort
- sort [-nrugMcszbdfimSTokt] [-o FILE] [-k start[.offset][opts][,end[.offset][opts]] [-t CHAR] [FILE]...
Sort lines of text
Options:
-b Ignore leading blanks -c Check whether input is sorted -d Dictionary order (blank or alphanumeric only) -f Ignore case -g General numerical sort -i Ignore unprintable characters -k Sort key -M Sort month -n Sort numbers -o Output to file -k Sort by key -t CHAR Key separator -r Reverse sort order -s Stable (don't sort ties alphabetically) -u Suppress duplicate lines -z Lines are terminated by NUL, not newline -mST Ignored for GNU compatibility
Example:
$ echo -e "e\nf\nb\nd\nc\na" | sort a b c d e f $ echo -e "c 3\nb 2\nd 2" | $SORT -k 2,2n -k 1,1r d 2 b 2 c 3
- split
- split [OPTION] [INPUT [PREFIX]]
Options:
-b n[k|m] Split by bytes -l n Split by lines -a n Use n letters as suffix
Example:
$ split TODO foo $ cat TODO | split -a 2 -l 2 TODO_
- start-stop-daemon
- start-stop-daemon [OPTIONS] [--start|--stop] ... [-- arguments...]
Start and stop services
Options:
-S,--start Start -K,--stop Stop -a,--startas pathname Start process specified by pathname -b,--background Put process into background -u,--user username|uid Stop this user's processes -x,--exec executable Program to either start or check -n,--name process-name Stop processes with this name -p,--pidfile pid-file Save or load pid using a pid-file -m,--make-pidfile Create the -p file and enter pid in it -q,--quiet Quiet -o,--oknodo Exit status 0 if nothing done -v,--verbose Verbose -N,--nicelevel N Add N to process's nice level -s,--signal signal Signal to send (default TERM) -c,--chuid user[:[grp]] Change to specified user/group -s signal Signal to send (default TERM) -c user[:[grp]] Change to specified user/group )
- stat
- stat [OPTION] FILE...
Display file (default) or filesystem status
Options:
-c fmt Use the specified format -f Display filesystem status -L Dereference links -t Display info in terse form -Z Print security context
Valid format sequences for files:
%a Access rights in octal %A Access rights in human readable form %b Number of blocks allocated (see %B) %B The size in bytes of each block reported by %b %d Device number in decimal %D Device number in hex %f Raw mode in hex %F File type %g Group ID of owner %G Group name of owner %h Number of hard links %i Inode number %n File name %N Quoted file name with dereference if symlink %o I/O block size %s Total size, in bytes %t Major device type in hex %T Minor device type in hex %u User ID of owner %U User name of owner %x Time of last access %X Time of last access as seconds since Epoch %y Time of last modification %Y Time of last modification as seconds since Epoch %z Time of last change %Z Time of last change as seconds since Epoch
Valid format sequences for file systems:
%a Free blocks available to non-superuser %b Total data blocks in file system %c Total file nodes in file system %d Free file nodes in file system %f Free blocks in file system %C Security context in SELinux %i File System ID in hex %l Maximum length of filenames %n File name %s Block size (for faster transfer) %S Fundamental block size (for block counts) %t Type in hex %T Type in human readable form
- strings
- strings [-afo] [-n length] [file...]
Display printable strings in a binary file
Options:
-a Scan whole file (default) -f Precede strings with filenames -n N At least N characters form a string (default 4) -o Precede strings with decimal offsets
- stty
- stty [-a|g] [-F DEVICE] [SETTING]...
Without arguments, prints baud rate, line discipline, and deviations from stty sane
Options:
-F DEVICE Open device instead of stdin -a Print all current settings in human-readable form -g Print in stty-readable form [SETTING] See manpage
- su
- su [OPTION]... [-] [username]
Change user id or become root
Options:
-p, -m Preserve environment -c Command to pass to 'sh -c' -s Shell to use instead of default shell
- sulogin
- sulogin [OPTION]... [tty-device]
Single user login
Options:
-t Timeout
- sum
- sum [rs] [files...]
Checksum and count the blocks in a file
Options:
-r Use BSD sum algorithm (1K blocks) -s Use System V sum algorithm (512byte blocks)
- sv
- sv [-v] [-w sec] command service...
Control services monitored by runsv supervisor. Commands (only first character is enough):
status: query service status up: if service isn't running, start it. If service stops, restart it once: like 'up', but if service stops, don't restart it down: send TERM and CONT signals. If ./run exits, start ./finish
if it exists. After it stops, do not restart service exit: send TERM and CONT signals to service and log service. If they exit, runsv exits too pause, cont, hup, alarm, interrupt, quit, 1, 2, term, kill: send STOP, CONT, HUP, ALRM, INT, QUIT, USR1, USR2, TERM, KILL signal to service
- svlogd
- svlogd [-ttv] [-r c] [-R abc] [-l len] [-b buflen] dir...
Continuously read log data from standard input, optionally filter log messages, and write the data to one or more automatically rotated logs
- swapoff
- swapoff [-a] [DEVICE]
Stop swapping on DEVICE
Options:
-a Stop swapping on all swap devices
- swapon
- swapon [-a] [DEVICE]
Start swapping on DEVICE
Options:
-a Start swapping on all swap devices
- switch_root
- switch_root [-c /dev/console] NEW_ROOT NEW_INIT [ARGUMENTS_TO_INIT]
Use from PID 1 under initramfs to free initramfs, chroot to NEW_ROOT, and exec NEW_INIT
Options:
-c Redirect console to device on new root
- sync
- sync
Write all buffered filesystem blocks to disk
- sysctl
- sysctl [OPTIONS]... [VALUE]...
Configure kernel parameters at runtime
Options:
-n Disable printing of key names -e Don't warn about unknown keys -w Change sysctl setting -p FILE Load sysctl settings from FILE (default /etc/sysctl.conf) -a Display all values -A Display all values in table form
Example:
sysctl [-n] [-e] variable... sysctl [-n] [-e] -w variable=value... sysctl [-n] [-e] -a sysctl [-n] [-e] -p file (default /etc/sysctl.conf) sysctl [-n] [-e] -A
- syslogd
- syslogd [OPTION]...
System logging utility. Note that this version of syslogd ignores /etc/syslog.conf.
Options:
-n Run in foreground -O FILE Log to given file (default=/var/log/messages) -l n Set local log level -S Smaller logging output -s SIZE Max size (KB) before rotate (default=200KB, 0=off) -b NUM Number of rotated logs to keep (default=1, max=99, 0=purge) -R HOST[:PORT] Log to IP or hostname on PORT (default PORT=514/UDP) -L Log locally and via network (default is network only if -R) -D Drop duplicates -C[size(KiB)] Log to shared mem buffer (read it using logread) /* NB: -Csize shouldn't have space (because size is optional) */
Example:
$ syslogd -R masterlog:514 $ syslogd -R 192.168.1.1:601
- tac
- tac [FILE]...
Concatenate FILE(s) and print them in reverse
- tail
- tail [OPTION]... [FILE]...
Print last 10 lines of each FILE to standard output. With more than one FILE, precede each with a header giving the file name. With no FILE, or when FILE is -, read standard input.
Options:
-c N[kbm] Output the last N bytes -n N[kbm] Print last N lines instead of last 10 -f Output data as the file grows -q Never output headers giving file names -s SEC Wait SEC seconds between reads with -f -v Always output headers giving file names
If the first character of N (bytes or lines) is a '+', output begins with the Nth item from the start of each file, otherwise, print the last N items in the file. N bytes may be suffixed by k (x1024), b (x512), or m (1024^2).
Example:
$ tail -n 1 /etc/resolv.conf nameserver 10.0.0.1
- tar
- tar -[czjaZxtvO] [-X FILE] [-f TARFILE] [-C DIR] [FILE(s)]...
Create, extract, or list files from a tar file
Options:
c Create x Extract t List Archive format selection: z Filter the archive through gzip j Filter the archive through bzip2 a Filter the archive through lzma Z Filter the archive through compress File selection: f Name of TARFILE or "-" for stdin O Extract to stdout exclude File to exclude X File with names to exclude C Change to directory DIR before operation v Verbose
Example:
$ zcat /tmp/tarball.tar.gz | tar -xf - $ tar -cf /tmp/tarball.tar /usr/local
- taskset
- taskset [-p] [mask] [pid | command [arg]...]
Set or get CPU affinity
Options:
-p Operate on an existing PID
Example:
$ taskset 0x7 ./dgemm_test& $ taskset -p 0x1 $! pid 4790's current affinity mask: 7 pid 4790's new affinity mask: 1 $ taskset 0x7 /bin/sh -c './taskset -p 0x1 $$' pid 6671's current affinity mask: 1 pid 6671's new affinity mask: 1 $ taskset -p 1 pid 1's current affinity mask: 3
- tcpsvd
- tcpsvd [-hEv] [-c n] [-C n:msg] [-b n] [-u user] [-l name] ip port prog...
Create TCP socket, bind it to ip:port and listen for incoming connection. Run PROG for each connection.
ip IP to listen on. '0' = all
port Port to listen on
prog [arg] Program to run
-l name Local hostname (else looks up local hostname in DNS)
-u user[:group] Change to user/group after bind
-c n Handle up to n connections simultaneously
-b n Allow a backlog of approximately n TCP SYNs
-C n[:msg] Allow only up to n connections from the same IPNew connections from this IP address are closed immediately. 'msg' is written to the peer before close B<-h> Look up peer's hostname B<-E> Do not set up environment variables B<-v> Verbose
- tee
- tee [OPTION]... [FILE]...
Copy standard input to each FILE, and also to standard output
Options:
-a Append to the given FILEs, do not overwrite -i Ignore interrupt signals (SIGINT)
Example:
$ echo "Hello" | tee /tmp/foo $ cat /tmp/foo Hello
- telnet
- telnet HOST [PORT]
Connect to telnet server
- telnetd
- telnetd [OPTION]
Handle incoming telnet connections
Options:
-l LOGIN Exec LOGIN on connect -f issue_file Display issue_file instead of /etc/issue -K Close connection as soon as login exits (normally wait until all programs close slave pty) -p PORT Port to listen on -b ADDR Address to bind to -F Run in foreground -i Run as inetd subservice
- test
- test EXPRESSION
or [ EXPRESSION ]Check file types and compares values returning an exit code determined by the value of EXPRESSION
Example:
$ test 1 -eq 2 $ echo $? 1 $ test 1 -eq 1 $ echo $? 0 $ [ -d /etc ] $ echo $? 0 $ [ -d /junk ] $ echo $? 1
- tftp
- tftp [OPTION]... HOST [PORT]
Transfer a file from/to tftp server
Options:
-l FILE Local FILE -r FILE Remote FILE -g Get file -p Put file -b SIZE Transfer blocks of SIZE octets
- tftpd
- tftpd [-cr] [-u USER] [DIR]
Transfer a file on tftp client's request.
Options:
-r Prohibit upload -c Allow file creation via upload -u Access files as USER
- time
- time [OPTION]... COMMAND [ARGS...]
Run the program COMMAND with arguments ARGS. When COMMAND finishes, COMMAND's resource usage information is displayed.
Options:
-v Verbose
- top
- top [-b] [-n COUNT] [-d SECONDS]
Provide a view of process activity in real time. Read the status of all processes from /proc each SECONDS and show the status for however many processes will fit on the screen.
- touch
- touch [-c] FILE [FILE...]
Update the last-modified date on the given FILE[s]
Options:
-c Do not create any files
Example:
$ ls -l /tmp/foo /bin/ls: /tmp/foo: No such file or directory $ touch /tmp/foo $ ls -l /tmp/foo -rw-rw-r-- 1 andersen andersen 0 Apr 15 01:11 /tmp/foo
- tr
- tr [-cds] STRING1 [STRING2]
Translate, squeeze, and/or delete characters from standard input, writing to standard output
Options:
-c Take complement of STRING1 -d Delete input characters coded STRING1 -s Squeeze multiple output characters of STRING2 into one character
Example:
$ echo "gdkkn vnqkc" | tr [a-y] [b-z] hello world
- traceroute
- traceroute [-FIldnrv] [-f 1st_ttl] [-m max_ttl] [-p port#] [-q nqueries] [-s src_addr] [-t tos] [-w wait] [-g gateway] [-i iface]
[-z pausemsecs] HOST [data size]
Trace the route to HOST
Options:
-F Set the don't fragment bit -I Use ICMP ECHO instead of UDP datagrams -l Display the ttl value of the returned packet -d Set SO_DEBUG options to socket -n Print hop addresses numerically rather than symbolically -r Bypass the normal routing tables and send directly to a host -v Verbose -m max_ttl Max time-to-live (max number of hops) -p port# Base UDP port number used in probes (default is 33434) -q nqueries Number of probes per 'ttl' (default 3) -s src_addr IP address to use as the source address -t tos Type-of-service in probe packets (default 0) -w wait Time in seconds to wait for a response (default 3 sec) -g Loose source route gateway (8 max)
- true
- true
Return an exit code of TRUE (0)
Example:
$ true $ echo $? 0
- tty
- tty
Print file name of standard input's terminal
Options:
-s Print nothing, only return exit status
Example:
$ tty /dev/tty2
- ttysize
- ttysize [w] [h]
Print dimension(s) of standard input's terminal, on error return 80x25
- tune2fs
- tune2fs [-c max-mounts-count] [-e errors-behavior] [-g group] [-i interval[d|m|w]] [-j] [-J journal-options] [-l] [-s sparse-flag] [-m reserved-blocks-percent] [-o [^]mount-options[,...]] [-r reserved-blocks-count] [-u user] [-C mount-count] [-L volume-label] [-M last-mounted-dir] [-O [^]feature[,...]] [-T last-check-time] [-U UUID] device
Adjust filesystem options on ext[23] filesystems
- udhcpc
- udhcpc [-Cfbnqtv] [-c CID] [-V VCLS] [-H HOSTNAME] [-i INTERFACE] [-p pidfile] [-r IP] [-s script] [-O dhcp-option]... [-P N]
-V,--vendorclass=CLASSID Vendor class identifier -i,--interface=INTERFACE Interface to use (default eth0) -H,-h,--hostname=HOSTNAME Client hostname -c,--clientid=CLIENTID Client identifier -C,--clientid-none Suppress default client identifier -p,--pidfile=file Create pidfile -r,--request=IP IP address to request -s,--script=file Run file at dhcp events (default /usr/share/udhcpc/default.script) -t,--retries=N Send up to N request packets -T,--timeout=N Try to get a lease for N seconds (default 3) -A,--tryagain=N Wait N seconds (default 20) after failure -f,--foreground Run in foreground -b,--background Background if lease is not immediately obtained -S,--syslog Log to syslog too -n,--now Exit with failure if lease is not immediately obtained -q,--quit Quit after obtaining lease -R,--release Release IP on quit -O,--request-option=OPT Request DHCP option OPT from server -P,--client-port N Use port N instead of default 68 -a,--arping Use arping to validate offered address -a Use arping to validate offered address )
- udhcpd
- udhcpd [-fS] [-P N] [configfile]
DHCP server
-f Run in foreground -S Log to syslog too -P N Use port N instead of default 67
- udpsvd
- udpsvd [-hEv] [-c n] [-u user] [-l name] ip port prog
Create UDP socket, bind it to ip:port and wait for incoming packets. Run PROG for each packet, redirecting all further packets with same peer ip:port to it
ip IP to listen on. '0' = all
port Port to listen on
prog [arg] Program to run
-l name Local hostname (else looks up local hostname in DNS)
-u user[:group] Change to user/group after bind
-c n Handle up to n connections simultaneously
-h Look up peer's hostname
-E Do not set up environment variables
-v Verbose
- umount
- umount [flags] FILESYSTEM|DIRECTORY
Unmount file systems
Options:
-a Unmount all file systems in /etc/mtab -n Don't erase /etc/mtab entries -r Try to remount devices as read-only if mount is busy -l Lazy umount (detach filesystem) -f Force umount (i.e., unreachable NFS server) -i Don't call /sbin/mount.<filesystem> helper -d Free loop device if it has been used
Example:
$ umount /dev/hdc1
- uname
- uname [-amnrspv]
Print system information.
Options:
-a Print all -m The machine (hardware) type -n Hostname -r OS release -s OS name (default) -p Processor type -v OS version
Example:
$ uname -a Linux debian 2.4.23 #2 Tue Dec 23 17:09:10 MST 2003 i686 GNU/Linux
- uncompress
- uncompress [-c] [-f] [name...]
Uncompress .Z file[s]
Options:
-c Extract to stdout -f Overwrite an existing file
- unexpand
- unexpand [-f][-a][-t NUM] [FILE|-]
Convert spaces to tabs, writing to standard output.
Options:
-a,--all Convert all blanks -f,--first-only Convert only leading blanks -t,--tabs=N Tabstops every N chars
- uniq
- uniq [-fscdu]... [INPUT [OUTPUT]]
Discard all but one of successive identical lines from INPUT (or standard input), writing to OUTPUT (or standard output)
Options:
-c Prefix lines by the number of occurrences -d Only print duplicate lines -u Only print unique lines -f N Skip the first N fields -s N Skip the first N chars (after any skipped fields)
Example:
$ echo -e "a\na\nb\nc\nc\na" | sort | uniq a b c
- unix2dos
- unix2dos [option] [FILE]
Convert FILE from unix to dos format. When no file is given, use stdin/stdout.
Options:
-u dos2unix -d unix2dos
- unlzma
- unlzma [OPTION]... [FILE]
Uncompress FILE (or standard input if FILE is '-' or omitted)
Options:
-c Write to standard output -f Force
- unzip
- unzip [-opts[modifiers]] file[.zip] [list] [-x xlist] [-d exdir]
Extract files from ZIP archives
Options:
-l List archive contents (with -q for short form) -n Never overwrite existing files (default) -o Overwrite files without prompting -p Send output to stdout -q Quiet -x Exclude these files -d Extract files into this directory
- uptime
- uptime
Display the time since the last boot
Example:
$ uptime 1:55pm up 2:30, load average: 0.09, 0.04, 0.00
- usleep
- usleep N
Pause for N microseconds
Example:
$ usleep 1000000 [pauses for 1 second]
- uudecode
- uudecode [-o outfile] [infile]
Uudecode a file Finds outfile name in uuencoded source unless -o is given
Example:
$ uudecode -o busybox busybox.uu $ ls -l busybox -rwxr-xr-x 1 ams ams 245264 Jun 7 21:35 busybox
- uuencode
- uuencode [-m] [infile] stored_filename
Uuencode a file to stdout
Options:
-m Use base64 encoding per RFC1521
Example:
$ uuencode busybox busybox begin 755 busybox <encoded file snipped> $ uudecode busybox busybox > busybox.uu $
- vconfig
- vconfig COMMAND [OPTIONS]...
Create and remove virtual ethernet devices
Options:
add [interface-name] [vlan_id] rem [vlan-name] set_flag [interface-name] [flag-num] [0 | 1] set_egress_map [vlan-name] [skb_priority] [vlan_qos] set_ingress_map [vlan-name] [skb_priority] [vlan_qos] set_name_type [name-type]
- vi
- vi [OPTION] [FILE]...
Edit FILE
Options:
-c Initial command to run ($EXINIT also available) -R Read-only - do not write to the file -H Short help regarding available features
- vlock
- vlock [OPTIONS]
Lock a virtual terminal. A password is required to unlock.
Options:
-a Lock all VTs
- watch
- watch [-n seconds] [-t] COMMAND...
Execute a program periodically
Options:
-n Loop period in seconds (default 2) -t Don't print header
Example:
$ watch date Mon Dec 17 10:31:40 GMT 2000 Mon Dec 17 10:31:42 GMT 2000 Mon Dec 17 10:31:44 GMT 2000
- watchdog
- watchdog [-t N[ms]] [-F] DEV
Periodically write to watchdog device DEV
Options:
-t N Timer period (default 30) -F Run in foreground
Use -t 500ms to specify period in milliseconds
- wc
- wc [OPTION]... [FILE]...
Print line, word, and byte counts for each FILE, and a total line if more than one FILE is specified. With no FILE, read standard input.
Options:
-c Print the byte counts -l Print the newline counts -L Print the length of the longest line -w Print the word counts
Example:
$ wc /etc/passwd 31 46 1365 /etc/passwd
- wget
- wget [-c|--continue] [-s|--spider] [-q|--quiet] [-O|--output-document file]
[--header 'header: value'] [-Y|--proxy on/off] [-P DIR]
[-U|--user-agent agent] url
Retrieve files via HTTP or FTP
Options:
-s Spider mode - only check file existence -c Continue retrieval of aborted transfer -q Quiet -P Set directory prefix to DIR -O Save to filename ('-' for stdout) -U Adjust 'User-Agent' field -Y Use proxy ('on' or 'off')
- which
- which [COMMAND...]
Locate a COMMAND
Example:
$ which login /bin/login
- who
- who [-a]
Show who is logged on
Options:
-a show all
- whoami
- whoami
Print the user name associated with the current effective user id
- xargs
- xargs [OPTIONS] [COMMAND] [ARGS...]
Execute COMMAND on every item given by standard input
Options:
-p Prompt the user about whether to run each command -r Do not run command for empty read lines -x Exit if the size is exceeded -0 Input filenames are terminated by a null character -t Print the command line on stderr before executing it
Example:
$ ls | xargs gzip $ find . -name '*.c' -print | xargs rm
- yes
- yes [OPTION]... [STRING]...
Repeatedly output a line with all specified STRING(s), or 'y'
- zcat
- zcat FILE
Uncompress to stdout
- zcip
- zcip [OPTIONS] ifname script
Manage a ZeroConf IPv4 link-local address
Options:
-f Run in foreground -q Quit after address (no daemon) -r 169.254.x.x Request this address first -v Verbose
LIBC NSS
GNU Libc (glibc) uses the Name Service Switch (NSS) to configure the behavior of the C library for the local environment, and to configure how it reads system data, such as passwords and group information. This is implemented using an /etc/nsswitch.conf configuration file, and using one or more of the /lib/libnss_* libraries. BusyBox tries to avoid using any libc calls that make use of NSS. Some applets however, such as login and su, will use libc functions that require NSS.If you enable CONFIG_USE_BB_PWD_GRP, BusyBox will use internal functions to directly access the /etc/passwd, /etc/group, and /etc/shadow files without using NSS. This may allow you to run your system without the need for installing any of the NSS configuration files and libraries.
When used with glibc, the BusyBox 'networking' applets will similarly require that you install at least some of the glibc NSS stuff (in particular, /etc/nsswitch.conf, /lib/libnss_dns*, /lib/libnss_files*, and /lib/libresolv*).
Shameless Plug: As an alternative, one could use a C library such as uClibc. In addition to making your system significantly smaller, uClibc does not require the use of any NSS support files or libraries.
MAINTAINER
Denis Vlasenko <vda.linux@googlemail.com>AUTHORS
The following people have contributed code to BusyBox whether they know it or not. If you have written code included in BusyBox, you should probably be listed here so you can obtain your bit of eternal glory. If you should be listed here, or the description of what you have done needs more detail, or is incorect, please send in an update.Emanuele Aina <emanuele.aina@tiscali.it> run-parts
Erik Andersen <andersen@codepoet.org>
Tons of new stuff, major rewrite of most of the core apps, tons of new apps as noted in header files. Lots of tedious effort writing these boring docs that nobody is going to actually read.
Laurence Anderson <l.d.anderson@warwick.ac.uk>
rpm2cpio, unzip, get_header_cpio, read_gz interface, rpm
Jeff Angielski <jeff@theptrgroup.com>
ftpput, ftpget
Edward Betts <edward@debian.org>
expr, hostid, logname, whoami
John Beppu <beppu@codepoet.org>
du, nslookup, sort
Brian Candler <B.Candler@pobox.com>
tiny-ls(ls)
Randolph Chung <tausq@debian.org>
fbset, ping, hostname
Dave Cinege <dcinege@psychosis.com>
more(v2), makedevs, dutmp, modularization, auto links file, various fixes, Linux Router Project maintenance
Jordan Crouse <jordan@cosmicpenguin.net>
ipcalc
Magnus Damm <damm@opensource.se>
tftp client insmod powerpc support
Larry Doolittle <ldoolitt@recycle.lbl.gov>
pristine source directory compilation, lots of patches and fixes.
Glenn Engel <glenne@engel.org>
httpd
Gennady Feldman <gfeldman@gena01.com>
Sysklogd (single threaded syslogd, IPC Circular buffer support, logread), various fixes.
Karl M. Hegbloom <karlheg@debian.org>
cp_mv.c, the test suite, various fixes to utility.c, &c.
Daniel Jacobowitz <dan@debian.org>
mktemp.c
Matt Kraai <kraai@alumni.cmu.edu>
documentation, bugfixes, test suite
Stephan Linz <linz@li-pro.net>
ipcalc, Red Hat equivalence
John Lombardo <john@deltanet.com>
tr
Glenn McGrath <bug1@iinet.net.au>
Common unarchving code and unarchiving applets, ifupdown, ftpgetput, nameif, sed, patch, fold, install, uudecode. Various bugfixes, review and apply numerous patches.
Manuel Novoa III <mjn3@codepoet.org>
cat, head, mkfifo, mknod, rmdir, sleep, tee, tty, uniq, usleep, wc, yes, mesg, vconfig, make_directory, parse_mode, dirname, mode_string, get_last_path_component, simplify_path, and a number trivial libbb routines also bug fixes, partial rewrites, and size optimizations in ash, basename, cal, cmp, cp, df, du, echo, env, ln, logname, md5sum, mkdir, mv, realpath, rm, sort, tail, touch, uname, watch, arith, human_readable, interface, dutmp, ifconfig, route
Vladimir Oleynik <dzo@simtreas.ru>
cmdedit; xargs(current), httpd(current); ports: ash, crond, fdisk, inetd, stty, traceroute, top; locale, various fixes and irreconcilable critic of everything not perfect.
Bruce Perens <bruce@pixar.com>
Original author of BusyBox in 1995, 1996. Some of his code can still be found hiding here and there...
Tim Riker <Tim@Rikers.org>
bug fixes, member of fan club
Kent Robotti <robotti@metconnect.com>
reset, tons and tons of bug reports and patches.
Chip Rosenthal <chip@unicom.com>, <crosenth@covad.com>
wget - Contributed by permission of Covad Communications
Pavel Roskin <proski@gnu.org>
Lots of bugs fixes and patches.
Gyepi Sam <gyepi@praxis-sw.com>
Remote logging feature for syslogd
Linus Torvalds <torvalds@transmeta.com>
mkswap, fsck.minix, mkfs.minix
Mark Whitley <markw@codepoet.org>
grep, sed, cut, xargs(previous), style-guide, new-applet-HOWTO, bug fixes, etc.
Charles P. Wright <cpwright@villagenet.com>
gzip, mini-netcat(nc)
Enrique Zanardi <ezanardi@ull.es>
tarcat (since removed), loadkmap, various fixes, Debian maintenance
Tito Ragusa <farmatito@tiscali.it>
devfsd and size optimizations in strings, openvt and deallocvt.
POD ERRORS
Hey! The above document had some coding errors, which are explained below:- Around line 125:
- Unterminated B<...> sequence
- Around line 137:
- Unterminated B<...> sequence
- Around line 155:
- Unterminated B<...> sequence
- Around line 172:
- Unterminated B<...> sequence
- Around line 188:
- Unterminated B<...> sequence
- Around line 214:
- Unterminated B<...> sequence
- Around line 236:
- Unterminated B<...> sequence
- Around line 245:
- Unterminated B<...> sequence
- Around line 257:
- Unterminated B<...> sequence
- Around line 275:
- Unterminated B<...> sequence
- Around line 283:
- Unterminated B<...> sequence
- Around line 292:
- Unterminated B<...> sequence
- Around line 315:
- Unterminated B<...> sequence
- Around line 328:
- Unterminated B<...> sequence
- Around line 339:
- Unterminated B<...> sequence
- Around line 347:
- Unterminated B<...> sequence
- Around line 363:
- Unterminated B<...> sequence
- Around line 376:
- Unterminated B<...> sequence
- Around line 393:
- Unterminated B<...> sequence
- Around line 407:
- Unterminated B<...> sequence
- Around line 418:
- Unterminated B<...> sequence
- Around line 449:
- Unterminated B<...> sequence
- Around line 470:
- Unterminated B<...> sequence
- Around line 497:
- Unterminated B<...> sequence
- Around line 524:
- Unterminated B<...> sequence
- Around line 554:
- Unterminated B<...> sequence
- Around line 568:
- Unterminated B<...> sequence
- Around line 597:
- Unterminated B<...> sequence
- Around line 614:
- Unterminated B<...> sequence
- Around line 636:
- Unterminated B<...> sequence
- Around line 644:
- Unterminated B<...> sequence
- Around line 652:
- Unterminated B<...> sequence
- Around line 660:
- Unterminated B<...> sequence
- Around line 674:
- Unterminated B<...> sequence
- Around line 688:
- Unterminated B<...> sequence
- Around line 708:
- Unterminated B<...> sequence
- Around line 725:
- Unterminated B<...> sequence
- Around line 739:
- Unterminated B<...> sequence
- Around line 752:
- Unterminated B<...> sequence
- Around line 765:
- Unterminated B<...> sequence
- Around line 789:
- Unterminated B<...> sequence
- Around line 815:
- Unterminated B<...> sequence
- Around line 845:
- Unterminated B<...> sequence
- Around line 885:
- Unterminated B<...> sequence
- Around line 893:
- Unterminated B<...> sequence
- Around line 901:
- Unterminated B<...> sequence
- Around line 919:
- Unterminated B<...> sequence
- Around line 953:
- Unterminated B<...> sequence
- Around line 979:
- Unterminated B<...> sequence
- Around line 994:
- Unterminated B<...> sequence
- Around line 1008:
- Unterminated B<...> sequence
- Around line 1024:
- Unterminated B<...> sequence
- Around line 1038:
- Unterminated B<...> sequence
- Around line 1056:
- Unterminated B<...> sequence
- Around line 1076:
- Unterminated B<...> sequence
- Around line 1113:
- Unterminated B<...> sequence
- Around line 1139:
- Unterminated B<...> sequence
- Around line 1161:
- Unterminated B<...> sequence
- Around line 1186:
- Unterminated B<...> sequence
- Around line 1194:
- Unterminated B<...> sequence
- Around line 1208:
- Unterminated B<...> sequence
- Around line 1222:
- Unterminated B<...> sequence
- Around line 1255:
- Unterminated B<...> sequence
- Around line 1268:
- Unterminated B<...> sequence
- Around line 1323:
- Unterminated B<...> sequence
- Around line 1337:
- Unterminated B<...> sequence
- Around line 1356:
- Unterminated B<...> sequence
- Around line 1364:
- Unterminated B<...> sequence
- Around line 1376:
- Unterminated B<...> sequence
- Around line 1413:
- Unterminated B<...> sequence
- Around line 1461:
- Unterminated B<...> sequence
- Around line 1473:
- Unterminated B<...> sequence
- Around line 1488:
- Unterminated B<...> sequence
- Around line 1516:
- Unterminated B<...> sequence
- Around line 1553:
- Unterminated B<...> sequence
- Around line 1569:
- Unterminated B<...> sequence
- Around line 1584:
- Unterminated B<...> sequence
- Around line 1609:
- Unterminated B<...> sequence
- Around line 1657:
- Unterminated B<...> sequence
- Around line 1679:
- Unterminated B<...> sequence
- Around line 1718:
- Unterminated B<...> sequence
- Around line 1740:
- Unterminated B<...> sequence
- Around line 1762:
- Unterminated B<...> sequence
- Around line 1777:
- Unterminated B<...> sequence
- Around line 1785:
- Unterminated B<...> sequence
- Around line 1833:
- Unterminated B<...> sequence
- Around line 1856:
- Unterminated B<...> sequence
- Around line 1879:
- Unterminated B<...> sequence
- Around line 1887:
- Unterminated B<...> sequence
- Around line 1908:
- Unterminated B<...> sequence
- Around line 1930:
- Unterminated B<...> sequence
- Around line 1947:
- Unterminated B<...> sequence
- Around line 1968:
- Unterminated B<...> sequence
- Around line 1989:
- Unterminated B<...> sequence
- Around line 2041:
- Unterminated B<...> sequence
- Around line 2057:
- Unterminated B<...> sequence
- Around line 2073:
- Unterminated B<...> sequence
- Around line 2208:
- Unterminated B<...> sequence
- Around line 2227:
- Unterminated B<...> sequence
- Around line 2246:
- Unterminated B<...> sequence
- Around line 2256:
- Unterminated B<...> sequence
- Around line 2272:
- Unterminated B<...> sequence
- Around line 2289:
- Unterminated B<...> sequence
- Around line 2304:
- Unterminated B<...> sequence
- Around line 2325:
- Unterminated B<...> sequence
- Around line 2337:
- Unterminated B<...> sequence
- Around line 2353:
- Unterminated B<...> sequence
- Around line 2368:
- Unterminated B<...> sequence
- Around line 2382:
- Unterminated B<...> sequence
- Around line 2397:
- Unterminated B<...> sequence
- Around line 2420:
- Unterminated B<...> sequence
- Around line 2437:
- Unterminated B<...> sequence
- Around line 2449:
- Unterminated B<...> sequence
- Around line 2462:
- Unterminated B<...> sequence
- Around line 2471:
- Unterminated B<...> sequence
- Around line 2479:
- Unterminated B<...> sequence
- Around line 2492:
- Unterminated B<...> sequence
- Around line 2509:
- Unterminated B<...> sequence
- Around line 2540:
- Unterminated B<...> sequence
- Around line 2552:
- Unterminated B<...> sequence
- Around line 2564:
- Unterminated B<...> sequence
- Around line 2582:
- Unterminated B<...> sequence
- Around line 2596:
- Unterminated B<...> sequence
- Around line 2609:
- Unterminated B<...> sequence
- Around line 2621:
- Unterminated B<...> sequence
- Around line 2645:
- Unterminated B<...> sequence
- Around line 2655:
- Unterminated B<...> sequence
- Around line 2668:
- Unterminated B<...> sequence
- Around line 2681:
- Unterminated B<...> sequence
- Around line 2721:
- Unterminated B<...> sequence
- Around line 2737:
- Unterminated B<...> sequence
- Around line 2745:
- Unterminated B<...> sequence
- Around line 2753:
- Unterminated B<...> sequence
- Around line 2804:
- Unterminated B<...> sequence
- Around line 2830:
- Unterminated B<...> sequence
- Around line 2863:
- Unterminated B<...> sequence
- Around line 2874:
- Unterminated B<...> sequence
- Around line 2890:
- Unterminated B<...> sequence
- Around line 2913:
- Unterminated B<...> sequence
- Around line 2942:
- Unterminated B<...> sequence
- Around line 2971:
- Unterminated B<...> sequence
- Around line 2994:
- Unterminated B<...> sequence
- Around line 3002:
- Unterminated B<...> sequence
- Around line 3028:
- Unterminated B<...> sequence
- Around line 3112:
- Unterminated B<...> sequence
- Around line 3124:
- Unterminated B<...> sequence
- Around line 3195:
- Unterminated B<...> sequence
- Around line 3210:
- Unterminated B<...> sequence
- Around line 3228:
- Unterminated B<...> sequence
- Around line 3248:
- Unterminated B<...> sequence
- Around line 3287:
- Unterminated B<...> sequence
- Around line 3308:
- Unterminated B<...> sequence
- Around line 3320:
- Unterminated B<...> sequence
- Around line 3351:
- Unterminated B<...> sequence
- Around line 3363:
- Unterminated B<...> sequence
- Around line 3381:
- Unterminated B<...> sequence
- Around line 3390:
- Unterminated B<...> sequence
- Around line 3402:
- Unterminated B<...> sequence
- Around line 3418:
- Unterminated B<...> sequence
- Around line 3432:
- Unterminated B<...> sequence
- Around line 3449:
- Unterminated B<...> sequence
- Around line 3470:
- Unterminated B<...> sequence
- Around line 3497:
- Unterminated B<...> sequence
- Around line 3532:
- Unterminated B<...> sequence
- Around line 3549:
- Unterminated B<...> sequence
- Around line 3563:
- Unterminated B<...> sequence
- Around line 3572:
- Unterminated B<...> sequence
- Around line 3586:
- Unterminated B<...> sequence
- Around line 3612:
- Unterminated B<...> sequence
- Around line 3627:
- Unterminated B<...> sequence
- Around line 3652:
- Unterminated B<...> sequence
- Around line 3673:
- Unterminated B<...> sequence
- Around line 3704:
- Unterminated B<...> sequence
- Around line 3712:
- Unterminated B<...> sequence
- Around line 3726:
- Unterminated B<...> sequence
- Around line 3741:
- Unterminated B<...> sequence
- Around line 3749:
- Unterminated B<...> sequence
- Around line 3777:
- Unterminated B<...> sequence
- Around line 3796:
- Unterminated B<...> sequence
- Around line 3808:
- Unterminated B<...> sequence
- Around line 3824:
- Unterminated B<...> sequence
- Around line 3838:
- Unterminated B<...> sequence
- Around line 3856:
- Unterminated B<...> sequence
- Around line 3864:
- Unterminated B<...> sequence
- Around line 3912:
- Unterminated B<...> sequence
- Around line 3929:
- Unterminated B<...> sequence
- Around line 3942:
- Unterminated B<...> sequence
- Around line 3950:
- Unterminated B<...> sequence
- Around line 3958:
- Unterminated B<...> sequence
- Around line 3970:
- Unterminated B<...> sequence
- Around line 3983:
- Unterminated B<...> sequence
- Around line 4016:
- Unterminated B<...> sequence
- Around line 4036:
- Unterminated B<...> sequence
- Around line 4051:
- Unterminated B<...> sequence
- Around line 4060:
- Unterminated B<...> sequence
- Around line 4091:
- Unterminated B<...> sequence
- Around line 4145:
- Unterminated B<...> sequence
- Around line 4164:
- Unterminated B<...> sequence
- Around line 4179:
- Unterminated B<...> sequence
- Around line 4198:
- Unterminated B<...> sequence
- Around line 4245:
- Unterminated B<...> sequence
- Around line 4287:
- Unterminated B<...> sequence
- Around line 4332:
- Unterminated B<...> sequence
- Around line 4393:
- Unterminated B<...> sequence
- Around line 4408:
- Unterminated B<...> sequence
- Around line 4424:
- Unterminated B<...> sequence
- Around line 4438:
- Unterminated B<...> sequence
- Around line 4450:
- Unterminated B<...> sequence
- Around line 4463:
- Unterminated B<...> sequence
- Around line 4484:
- Unterminated B<...> sequence
- Around line 4492:
- Unterminated B<...> sequence
- Around line 4504:
- Unterminated B<...> sequence
- Around line 4529:
- Unterminated B<...> sequence
- Around line 4537:
- Unterminated B<...> sequence
- Around line 4562:
- Unterminated B<...> sequence
- Around line 4589:
- Unterminated B<...> sequence
- Around line 4597:
- Unterminated B<...> sequence
- Around line 4625:
- Unterminated B<...> sequence
- Around line 4658:
- Unterminated B<...> sequence
- Around line 4682:
- Unterminated B<...> sequence
- Around line 4706:
- Unterminated B<...> sequence
- Around line 4725:
- Unterminated B<...> sequence
- Around line 4733:
- Unterminated B<...> sequence
- Around line 4752:
- Unterminated B<...> sequence
- Around line 4777:
- Unterminated B<...> sequence
- Around line 4793:
- Unterminated B<...> sequence
- Around line 4807:
- Unterminated B<...> sequence
- Around line 4820:
- Unterminated B<...> sequence
- Around line 4830:
- Unterminated B<...> sequence
- Around line 4850:
- Unterminated B<...> sequence
- Around line 4899:
- Unterminated B<...> sequence
- Around line 4913:
- Unterminated B<...> sequence
- Around line 4930:
- Unterminated B<...> sequence
- Around line 4938:
- Unterminated B<...> sequence
- Around line 4946:
- Unterminated B<...> sequence
- Around line 4975:
- Unterminated B<...> sequence
- Around line 4987:
- Unterminated B<...> sequence
- Around line 5007:
- Unterminated B<...> sequence
- Around line 5029:
- Unterminated B<...> sequence
- Around line 5065:
- Unterminated B<...> sequence
- Around line 5079:
- Unterminated B<...> sequence
- Around line 5103:
- Unterminated B<...> sequence
- Around line 5117:
- Unterminated B<...> sequence
- Around line 5130:
- Unterminated B<...> sequence
- Around line 5148:
- Unterminated B<...> sequence
- Around line 5161:
- Unterminated B<...> sequence
- Around line 5174:
- Unterminated B<...> sequence
- Around line 5189:
- Unterminated B<...> sequence
- Around line 5209:
- Unterminated B<...> sequence
- Around line 5226:
- Unterminated B<...> sequence
- Around line 5240:
- Unterminated B<...> sequence
- Around line 5252:
- Unterminated B<...> sequence
- Around line 5272:
- Unterminated B<...> sequence
- Around line 5287:
- Unterminated B<...> sequence
- Around line 5308:
- Unterminated B<...> sequence
- Around line 5328:
- Unterminated B<...> sequence
- Around line 5341:
- Unterminated B<...> sequence
- Around line 5353:
- Unterminated B<...> sequence
- Around line 5361:
- Unterminated B<...> sequence
- Around line 5382:
- Unterminated B<...> sequence
- Around line 5390:
- Unterminated B<...> sequence
- Around line 5398:
- Unterminated B<...> sequence
Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre