Rechercher une page de manuel

Chercher une autre page de manuel:


Langue: en

Autres versions - même langue

Version: 371504 (fedora - 01/12/10)

Section: 1 (Commandes utilisateur)


i.zc - Zero-crossing "edge detection" raster function for image processing.




i.zc help
i.zc input=string output=string [width=integer] [threshold=float] [orientations=integer] [--overwrite] [--verbose] [--quiet]



Allow output files to overwrite existing files

Verbose module output

Quiet module output



Name of input raster map

Zero crossing raster map

x-y extent of the Gaussian filter
Default: 9

Sensitivity of Gaussian filter
Default: 10

Number of azimuth directions categorized
Default: 1


i.zc is an image processing program used for edge detection. The raster map produced shows the location of dqboundaries" on the input map. Boundaries tend to be found in regions of changing cell values and tend to run perpendicular to the direction of the slope. The algorithm used for edge detection is one of the "zero-crossing" algorithms and is discussed briefly below.

This program will be run interactively if the user types i.zc without program arguments on the command line. In this event, the program will prompt the user for parameter values using the standard interface described in the manual entry for parser. Alternately, the user can run the program non-interactively by specifying program parameter values on the command line.




Name of input raster map layer.

Name of raster map layer to be used for zero-crossing values.

This parameter determines the x-y extent of the Gaussian filter. The default value is 9; higher and lower values can be tested by the user. Increasing the width will result in finding "edges" representing more gradual changes in cell values.
Default: 9

This parameter determines the "sensitivity" of the Gaussian filter. The default value is 10; higher and lower values can be tested by the user. Increasing the threshold value will result in fewer edges being found.
Default: 10

This value is the number of azimuth directions the cells on the output raster map layer are categorized into (similar to the aspect raster map layer produced by the r.slope.aspect program). For example, a value of 16 would result in detected edges being categorized into one of 16 bins depending on the direction of the edge at that point.
Default: 1

The current region definition and mask settings are respected when reading the input map.


The procedure to find the "edges" in the image is as follows: The Fourier transform of the image is taken, The Fourier transform of the Laplacian of a two-dimensional Gaussian function is used to filter the transformed image, The result is run through an inverse Fourier transform, The resulting image is traversed in search of places where the image changes from positive to negative or from negative to positive, Each cell in the map where the value crosses zero (with a change in value greater than the threshold value) is marked as an edge and an orientation is assigned to it. The resulting raster map layer is output.


i.fft, i.ifft, r.mapcalc, r.mfilter, r.slope.aspect


David Satnik, GIS Laboratory, Central Washington University

Last changed: $Date: 2003-04-17 16:51:33 +0200 (Thu, 17 Apr 2003) $

Full index

© 2003-2008 GRASS Development Team

<Qui_Gon> je veux pinger ma machine qui est en ip sur mon réseau local
<Jayge> Qui_Gon> pourquoi tu les as pas appellée 192.168.* comme tout le monde ???
<Qui_Gon> ok je change alors
<Jayge> Ouais, les classes A je connais c'est les modems ADSL surtout, les classes C c'est utilisé dans les reseaux mais les B?
<lc_> Jayge: les classes A ont ete invente avant les modems ADSL
<Jayge> Lc_> j'ai pas dit le contraire
<Jayge> Lc_> j'ai dit que l'utilisation la plus courante était POUR les modems ADSL !
<Jayge> nuance