Rechercher une page de manuel

Chercher une autre page de manuel:


Langue: en

Version: 369297 (fedora - 01/12/10)

Section: 1 (Commandes utilisateur)


lcdproc - system status information client


lcdproc [-hfv] [-c config] [-s host] [-p port] [-e delay] [screen ...]


lcdproc is the client in the LCDproc suite that displays information about the local system's status on an LCD that is connected to an LCDd server daemon.

Due to the client-server architecture it does not matter whether the LCDd daemon runs on the local machine or on a remote system.

Most settings of lcdproc are configured through its configuration file /etc/sysconfig/lcdproc/lcdproc.conf, some of them can be overriden using command line options.

Before running lcdproc you should carefully read through that file and modify the settings therein according to your needs.

When compiled appropriately, some aspects of lcdproc can even configured at run time using a menu on the LCD.

Currently, only Linux, the BSD variants FreeBSD, NetBSD, OpenBSD and Darwin as well as Solaris are supported, but not all features may be available on all platforms.


lcdproc understands these command line options:
-c config
Use a configuration file other than /etc/sysconfig/lcdproc/LCDd.conf
-s host
Connect to the LCDd server on host, instead to the one listed in te Server parameter in the config file's [lcdproc] section. If not given here and not specified in the config file or if the default config file does not exist, it defaults to 'localhost.
-p port
Use port port when connecting to the LCDd server on host. This option overrides the Port parameter in the config file's [lcdproc] section. Without a default config file or when not set in the config file, it defaults to the LCDproc port 13666.
Run in the foreground, overriding the Foreground parameter in the config file's [lcdproc] section. The default, if not in the config file or without a config file, is to daemonize lcdproc as it is intended to display the system information in the background.
-e delay
Sleep delay in 100ths of seconds between updating screens in an update cycle. This option overrides the Delay parameter in the config file's [lcdproc] section. When not given and not in the config file, it defaults to 0.
Show help screen.
Print the version of lcdproc and exit.
can be one of the following:
show detailed CPU usage
CPU usage overview: one line per CPU, especially useful on SMP systems.
G CPUGraph
CPU histogram
L Load
Load histogram
M Memory
memory & swap usage
S ProcSize
memory usage of 5 biggest processes
D Disk
filling level of the mounted file systems
I Iface
network interface usage
B Battery
battery status
T TimeDate
time & date information
O OldTime
old time screen
U Uptime
uptime screen
K BigClock
big clock
N MiniClock
minimal clock
A About
credits page

On the command line you may either use the short or the long screen name. In the config file, the long names are used as section labels to configure the screens further.

You may also prefix the screen names with an exclamation mark '!' to disable a screen that was activated in the config file instead of activating a disabled one.


lcdproc C M D '!L'

With the command line specified above, lcdproc loads the default configuration file, connects to the LCDd server specified therein and then displays the following screens in addition to those activated in the configuration file on the LCD:

detailed CPU Usage
Memory & swap usage
filling level of the mounted file systems


Load histogram

screen is disabled and therefore not shown in the display. (The quotes are not part of lcdproc's command line syntax; they are required to disable special interpretation of the exclamation mark by the shell).


/etc/sysconfig/lcdproc/lcdproc.conf, lcdproc's default configuration file


LCDd(8), lcdproc-config(5)


LCDproc was originally written by William Ferrell ( andr Scott Scriven (

Since that time various people have contributed to LCDproc.

The newest version of LCDproc should be available from here:


LCDproc is released as "WorksForMe-Ware". In other words, it is free, kinda neat, and we don't guarantee that it will do anything in particular on any machine except the ones it was developed on.

It is technically released under the GNU GPL license (you should have received the file, "COPYING", with LCDproc) (also, look on for more information), so you can distribute and use it for free -- but you must make the source code freely available to anyone who wants it.

For any sort of real legal information, read the GNU GPL (GNU General Public License). It's worth reading.

Si la pierre tombe sur l'oeuf, malheur à l'oeuf.
Mais si l'oeuf tombe sur la pierre, malheur à l'oeuf.