tcpprof

Langue: en

Version: 113768 (mandriva - 01/05/08)

Section: 1 (Commandes utilisateur)


BSD mandoc

NAME

tcpprof - report profile of network traffic

SYNOPSIS

[-?hdnpR ] [-f filter expr ] [-i interface ] [-P port ] [-r filename ] [-s seconds ] [-S letters ] [-t lines ]

DESCRIPTION

reports a profile of network traffic by ranking it by link type, ip protocol, TCP/UDP port, ip address, or network address.

Network information is collected either by reading data from filename or by directly monitoring the network interface interface The default action for is to automatically search for an appropriate interface, and to generate a profile before it exits.

When reading data from filename will display the profile and exit immediately after the entire file has been processed. When collecting data from interface will keep running unless the -s option had been specified.

OPTIONS

The options are as follows:
-f filter expr
Filter the packets according the rules given by filter expr For the syntax of these rules, see tcpdump(1). The argument must be quoted if it contains spaces in order to separate it from other options.
-h , -
Display version and a brief help message.
-d
will track the source and destination information separately, where applicable, and identify source data with a ">" and destination data with "<". For example, a "http <" statistic signifies all traffic with destination port 80 (http). This option only applies to port, host and network statistics.
-i interface
Do a live capture (rather than read from a file) on the interface interface given on the command line. If interface is "auto" then tries to find an appropriate one by itself.
-P port
This tells to ignore TCP and UDP ports greater than or equal to port when displaying port statistics. This is not the same as filtering these port numbers out of the data set. This way, packets with i.e. the source port above port and the destination port below port will be able to still count the lower port number as a statistic. In addition, this doesn't affect the other statistic types (link, protocol, etc.)
-p
Set the interface into non-promiscuous mode (promiscuous is the default) when doing live captures.
-r filename
Read all data from filename which may be a regular file, a named pipe or "-" to read it's data from standard input. Acceptable file formats include pcap (tcpdump1 files) and "snoop" format files. filename is usually a file created by the tcpdump(1) command using the "-w" option.
-S letters
Tells which statistics to display. letters must be a string of one or more of the following letters:
l
show stats about the link layer
i
show stats about all ip protocols
p
show stats about TCP/UDP ports
h
show stats about hosts/ip addresses
n
show stats about network addresses
a
a synonym for "liphn"
-s seconds
When monitoring an interface, runs for only seconds seconds, and then quits. Has no effect when reading data from a file.
-t lines
When printing a profile of the data, will display a maximum of lines lines for each statistic.

SIGNALS

Upon receiving a SIGINT, will print any remaining statistics, and then exit.

FILES

/dev/bpf n
the packet filter device

EXAMPLES

tcpprof -i fxp0 -S a

Displays a complete profile of network data passing through the fxp0 network interface, after the user enters ^C (control C).

tcpprof -r file.dump -S a

Displays a complete profile of network data from the tcpdump(1) generated file "file.dump".

SEE ALSO

tcpdump(1), pcap(3), bpf(4)

HISTORY

was first written along side tcpstat in Winter 1998 using FreeBSD 3.0, and then finaly retrofited for Linux in Spring 2000. It became installed along with tcpstat since version 1.5.

AUTHORS

An Paul Herman Aq pherman@frenchfries.net
Cologne, Germany.

Please send all bug reports to this address.

BUGS

Not tested with link types other than Ethernet, PPP, and "None" types.

There may be problems reading non-IPv4 packets across platforms when reading null type link layers. This is due to a lack of a standardized packet type descriptor in libpcap for this link type.

Snoop file formats cannot be read from stdin or named pipes.