Rechercher une page de manuel
tsreport
Langue: en
Version: November 2008 (debian - 07/07/09)
Section: 1 (Commandes utilisateur)
Sommaire
NAME
tsreport - report on a Transport StreamSYNOPSIS
tsreport [switches] <infile> [switches]DESCRIPTION
- TS tools version 1.11, tsreport built Nov 11 2008 17:15:48
- Report on one of the following for the given Transport Stream:
- * The number of TS packets. * PCR and PTS/DTS differences (-buffering). * The packets of a single PID (-justpid).
- When conflicting switches are specified, the last takes effect.
Input:
- <infile>
- Read data from the named H.222 Transport Stream file
- -stdin
- Read data from standard input
Normal operation:
- By default, normal operation just reports the number of TS packets.
- -timing, -t Report timing information based on the PCRs
- -data Show TS packet/payload data as bytes
- -verbose, -v Also output (fairly detailed) information on each TS packet
- -quiet, -q Only output summary information (this is the default)
- -max <n>, -m <n> Maximum number of TS packets to read
Buffering information:
- -buffering, -b
- Report on the differences between PCR and PTS, and between PCR and DTS. This is relevant to the size of buffers needed in the decoder.
- -o <file>
- Output CSV data for -buffering to the named file.
- -32
- Truncate 33 bit values in the CSV output to 32 bits (losing the top bit).
- -verbose, -v
- Output PCR/PTS/DTS information as it is found (in a format similar to that used for -o)
- -quiet, -q
- Output less information (notably, not the PMT)
- -cnt <pid>,
- Check values of continuity_counter in the specified PID. Writes all the values of the counter to a file called 'continuity_counter.txt'. Turns buffering on (-b).
- -max <n>, -m <n>
- Maximum number of TS packets to read
Single PID:
- -justpid <pid>
- Just show data (file offset, index, adaptation field and payload) for TS packets with the given PID. PID 0 is allowed (i.e., the PAT).
- -verbose, -v
- Is ignored
- -quiet, -q
- Is ignored
- -max <n>, -m <n>
- Maximum number of TS packets of that PID to read
Experimental control of timestamp formats (this doesn't affect the output to the CVS file, produced with -o):
- -tfmt <thing>
- Specify format of time differences.
- -tafmt <thing>
- Specify format of absolute times.
- <thing> is (currently, but may change) one of:
- 90
- Default -- show as 90KHz timestamps (suffix 't' on the values: e.g., 4362599t).
- 27
- Show as 27MHz timestamps (similar, e.g., 25151:000t).
- 32
- Show as 90KHz timestamps, but only the low 32 bits.
- ms
- Show as milliseconds.
- hms
- Show as hours/minutes/seconds (H:MM:SS.ssss, the H can be more than one digit if necessary)
- TS tools version 1.11, tsreport built Nov 11 2008 17:15:48
- Report on one of the following for the given Transport Stream:
- * The number of TS packets. * PCR and PTS/DTS differences (-buffering). * The packets of a single PID (-justpid).
- When conflicting switches are specified, the last takes effect.
Input:
- <infile>
- Read data from the named H.222 Transport Stream file
- -stdin
- Read data from standard input
Normal operation:
- By default, normal operation just reports the number of TS packets. -timing, -t Report timing information based on the PCRs. -data Show TS packet/payload data as bytes -verbose, -v Also output (fairly detailed) information on each TS packet. -quiet, -q Only output summary information (this is the default) -max <n>, -m <n> Maximum number of TS packets to read
Buffering information:
- -buffering, -b
- Report on the differences between PCR and PTS, and between PCR and DTS. This is relevant to the size of buffers needed in the decoder.
- -o <file>
- Output CSV data for -buffering to the named file.
- -32
- Truncate 33 bit values in the CSV output to 32 bits (losing the top bit).
- -verbose, -v
- Output PCR/PTS/DTS information as it is found (in a format similar to that used for -o)
- -quiet, -q
- Output less information (notably, not the PMT)
- -cnt <pid>,
- Check values of continuity_counter in the specified PID. Writes all the values of the counter to a file called 'continuity_counter.txt'. Turns buffering on (-b).
- -max <n>, -m <n>
- Maximum number of TS packets to read
Single PID:
- -justpid <pid>
- Just show data (file offset, index, adaptation field and payload) for TS packets with the given PID. PID 0 is allowed (i.e., the PAT).
- -verbose, -v
- Is ignored
- -quiet, -q
- Is ignored
- -max <n>, -m <n>
- Maximum number of TS packets of that PID to read
Experimental control of timestamp formats (this doesn't affect the output to the CVS file, produced with -o):
- -tfmt <thing>
- Specify format of time differences.
- -tafmt <thing>
- Specify format of absolute times.
- <thing> is (currently, but may change) one of:
- 90
- Default -- show as 90KHz timestamps (suffix 't' on the values: e.g., 4362599t).
- 27
- Show as 27MHz timestamps (similar, e.g., 25151:000t).
- 32
- Show as 90KHz timestamps, but only the low 32 bits.
- ms
- Show as milliseconds.
- hms
- Show as hours/minutes/seconds (H:MM:SS.ssss, the H can be more than one digit if necessary)
SEE ALSO
The full documentation for tsreport is maintained as a Texinfo manual. Please check http://tstools.berlios.de for more information.Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre