Rechercher une page de manuel
vche-raw
Langue: en
Version: 312944 (ubuntu - 07/07/09)
Section: 1 (Commandes utilisateur)
Sommaire
NAME
vche - virtual console hex editorSYNOPSIS
vche [filename...]vche-nc [filename...]
vche-raw [filename...]
DESCRIPTION
vche is a hex editor and viewer which lets you see all the 256 characters, as found in video ROM.It uses the /dev/vcs[1-63] and /dev/vcsa[0-63] character devices to do all it's screen I/O. So this version will run only on Linux on a local console, and not under X or remote sessions.
vche-nc It is the NCURSES version, it will use that library to do all the screen I/O, so it will not show non-printable ASCII.
vche-raw It is the Run AnyWhere version (or RAW version, his name is twofold), it does all the screen I/O using the linux console escape and control sequences, for more information see the console_codes(4) man page.
Flags
There are six flags, each one shows the current program state and the behavior vche will have. See vche.conf(5) for a complete description.Bit operations
When you are in edit mode you can press F3 to set the edit mask. The edit mask is a mask used in bit operations. If you want, for example, to XOR some bytes, the value used to XOR that bytes is the edit mask. The bit operations are:- XOR
- Do a XOR on the byte at cursor position with the value set in the edit mask.
- OR
- Do an OR.
- AND
- Do an AND.
- NEG
- Negates the bytes at cursor position.
- ADD and SUB
- Adds or substract 1 from the bytes you want.
You could enter the edit mask as a decimal or as hex number, prefixing a "0x" to it (like in C).
Miscellaneous
If you provided more than one filename at the command line, you could view or edit any of them easily using the commands: n to go to the next file and p to go to the previous file. You could also press F7 to browse the list of files and select one manually, moving with the arrow keys.COMMANDS
- c-c
- Control-C, kills the program. (use it if you are in trouble).
The keys have different meanings if you are in view or edit mode:
View mode
- q, F10
- Quits the program.
- ?, h, H, F1
- Shows a helpless help.
- w
- Toggle read-write/read-only mode.
- b
- Toggle bell flag.
- n
- Open the next file (if any).
- p
- Open the previous file (if any).
- F7
- Select another file manually from the file list given at the command line.
- e, F2
- Enter edit mode.
- x, F3
- Toggle hex window viewing.
- s, F4
- Search a string taking care of case. (Prefix a "0x" to enter the string in hexadecimal).
- S
- Search a string ignoring case.
- SPACE, F5
- Search again.
- r
- Redraw the screen, it is needed when other process writes to the current tty and the screen gets corrupted. It is also useful when viewing files or devices whose contents change.
- R
- Refresh file size, use it if the size of the file changes during viewing, by any reason.
- m
- Toggle non-printable character mask.
- 0
- Toggle zero mask.
- g, F6
- Seek to an offset (to enter an hexadecimal offset you must prefix it with a "0x").
- F8
- Shows you the ascii table (as found in character ROM), shows also in hex, octal, decimal and binary.
- F9
- Shows GNU GPL (General Public License).
- HOME KEY
- Go to the beginning of the file.
- END KEY
- Go to the end of the file.
- LEFT KEY
- Go back a byte.
- RIGHT KEY
- Go forward a byte.
- UP KEY
- Go back a line.
- DOWN KEY
- Go forward a line.
- PGUP KEY
- Go back a page.
- PGDN KEY
- Go forward a page.
Edit mode
- TAB KEY
- Switch beetwen HEX and ASCII editing.
- F2
- Save changes (if any).
- F3
- Set the edit mask (needed for XOR, OR and AND operations).
- F4
- Do a XOR.
- F5
- Do an OR.
- F6
- Do an AND.
- F7
- Negates the byte at cursor position.
- F8
- Add 1 to the byte at the cursor position.
- F9
- Substract 1.
- F10
- Abort changes made.
- HOME KEY
- Go to the beginning of the file.
- END KEY
- Go to the end of the file.
- LEFT KEY
- Move the cursor to the left.
- RIGHT KEY
- Move the cursor to the right.
- UP KEY
- Move the cursor up.
- DOWN KEY
- Move the cursor down.
- PGUP KEY
- Go back a page.
- PGDN KEY
- Go forward a page.
VIEWING DEVICES
As with regular files you can also view or edit devices. Since there is no standard way to get the size of a device, each time you change the read-only flag, open or refresh the size of a device, vche will pop up a menu where you have to select the way the program will get his size, the three available options are:- Ask kernel
- This option will use Linux kernel ioctls to get the size of the device. Not all devices provide with such ioctl(2) calls, so, if you select this option and the ioctl fails, the file size will be set to LONG_MAX, or to 2147483647 if LONG_MAX is not defined, and an error message will be issued. You should use this option with IDE, SCSI, loop and with any device which support the BLKGETSIZE or FDGETPRM ioctl call.
- Let vche guess it
- If you select this option, to find the device size, the program will lseek(2) to different offsets doing a binary search until the lseek call fails. It works with almost any device, it is used mainly with RAM, kernel memory or other character devices, but you could use it with anything if you are in doubt. As with the Ask kernel option the device size can not be greater than a signed long (LONG_MAX), because it is the maximal value the lseek(2) call could handle.
- Enter it manually
- This option will let you enter whatever device size you want, once you entered it the device will look as the desired size, you can not see or edit beyond that offset. To change the offset simply refresh the file size with the R command.
FILES
/build/buildd/vche-1.7.2/debian/vche/etc/vche.conf Config file (optional)SEE ALSO
vche.conf(5), vcs(4), vcsa(4), ioctl(2), lseek(2), console_codes(4), charsets(4), terminfo(5), ncurses(3x).BUGS
None for now, if you find one, mail it to me <diego@grigna.com>VERSION
VCHE is at version 1.7.2.The latest version of VCHE could be found at:
http://www.grigna.com/diego/linux/vche/
AUTHOR
Diego Javier Grigna <diego@grigna.com>
Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre