Rechercher une page de manuel
fence_apc_snmp
Langue: en
Version: 2009-10-20 (fedora - 01/12/10)
Section: 8 (Commandes administrateur)
NAME
fence_apc_snmp - Fence agent for APC over SNMPDESCRIPTION
fence_apc_snmp is an I/O Fencing agent which can be used with the APC network power switch. It logs into a device via SNMP and reboots a specified outlet. It supports SNMP v1 and v3 with all combinations of authenticity/privacy settings. fence_apc_snmp accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_apc_snmp can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.Vendor URL: http://www.apc.com
PARAMETERS
- -o, --action=<action>
- Fencing Action (Default Value: reboot)
- -a, --ip=<ip>
- IP Address or Hostname This parameter is always required.
- -l, --username=<name>
- Login Name
- -p, --password=<password>
- Login password or passphrase
- -S, --password-script=<script>
- Script to retrieve password
- -n, --plug=<id>
- Physical plug number or name of virtual machine This parameter is always required.
- -d, --snmp-version=<ver>
- Specifies SNMP version to use (1,2c,3) (Default Value: 1)
- -c, --community=<community>
- Set the community string (Default Value: private)
- -b, --snmp-auth-prot=<prot>
- Set authentication protocol (MD5|SHA)
- -E, --snmp-sec-level=<level>
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- -B, --snmp-priv-prot=<prot>
- Set privacy protocol (DES|AES)
- -P, --snmp-priv-passwd=<pass>
- Set privacy protocol password
- -R, --snmp-priv-passwd-script
- Script to run to retrieve privacy password
- -u, --udpport
- UDP/TCP port to use for connection with device (Default Value: 161)
- -4, --inet4-only
- Forces agent to use IPv4 addresses only
- -6, --inet6-only
- Forces agent to use IPv6 addresses only
- -v, --verbose
- Verbose mode
- -D, --debug-file=<debugfile>
- Write debug information to given file
- -V, --version
- Display version information and exit
- -h, --help
- Display help and exit
- -C, --separator=<char>
- Separator for CSV created by operation list (Default Value: ,)
- --power-timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- --shell-timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- --login-timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- --power-wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- --retry-on
- Count of attempts to retry power on (Default Value: 1)
- --delay
- Wait X seconds before fencing is started (Default Value: 0)
ACTIONS
- on
- Power on machine.
- off
- Power off machine.
- reboot
- Reboot machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.
- monitor
- Check if fencing device is running. List available plugs/virtual machines or get status of machine (if it does not support more).
- metadata
The operational behavior of this is not known.
STDIN PARAMETERS
- action
- Fencing Action (Default Value: reboot)
- ipaddr
- IP Address or Hostname This parameter is always required.
- login
- Login Name
- passwd
- Login password or passphrase
- passwd_script
- Script to retrieve password
- port
- Physical plug number or name of virtual machine This parameter is always required.
- snmp_version
- Specifies SNMP version to use (1,2c,3) (Default Value: 1)
- community
- Set the community string (Default Value: private)
- snmp_auth_prot
- Set authentication protocol (MD5|SHA)
- snmp_sec_level
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- snmp_priv_prot
- Set privacy protocol (DES|AES)
- snmp_priv_passwd
- Set privacy protocol password
- snmp_priv_passwd_script
- Script to run to retrieve privacy password
- udpport
- UDP/TCP port to use for connection with device (Default Value: 161)
- inet4_only
- Forces agent to use IPv4 addresses only
- inet6_only
- Forces agent to use IPv6 addresses only
- verbose
- Verbose mode
- debug
- Write debug information to given file
- version
- Display version information and exit
- help
- Display help and exit
- separator
- Separator for CSV created by operation list (Default Value: ,)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- retry_on
- Count of attempts to retry power on (Default Value: 1)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre