Rechercher une page de manuel
fence_intelmodular
Langue: en
Version: 2009-10-20 (fedora - 01/12/10)
Section: 8 (Commandes administrateur)
NAME
fence_intelmodular - Fence agent for Intel ModularDESCRIPTION
fence_intelmodular is an I/O Fencing agent which can be used with Intel Modular device (tested on Intel MFSYS25, should work with MFSYS35 as well). Note: Since firmware update version 2.7, SNMP v2 write support is removed, and replaced by SNMP v3 support. So agent now has default SNMP version 3. If you are using older firmware, please supply -d for command line and snmp_version option for your cluster.conf. fence_intelmodular accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_intelmodular can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.Vendor URL: http://www.intel.com
PARAMETERS
- -o, --action=<action>
- Fencing Action (Default Value: reboot)
- -a, --ip=<ip>
- IP Address or Hostname This parameter is always required.
- -l, --username=<name>
- Login Name
- -p, --password=<password>
- Login password or passphrase
- -S, --password-script=<script>
- Script to retrieve password
- -n, --plug=<id>
- Physical plug number or name of virtual machine This parameter is always required.
- -d, --snmp-version=<ver>
- Specifies SNMP version to use (1,2c,3)
- -c, --community=<community>
- Set the community string
- -b, --snmp-auth-prot=<prot>
- Set authentication protocol (MD5|SHA)
- -E, --snmp-sec-level=<level>
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- -B, --snmp-priv-prot=<prot>
- Set privacy protocol (DES|AES)
- -P, --snmp-priv-passwd=<pass>
- Set privacy protocol password
- -R, --snmp-priv-passwd-script
- Script to run to retrieve privacy password
- -u, --udpport
- UDP/TCP port to use for connection with device (Default Value: 161)
- -4, --inet4-only
- Forces agent to use IPv4 addresses only
- -6, --inet6-only
- Forces agent to use IPv6 addresses only
- -v, --verbose
- Verbose mode
- -D, --debug-file=<debugfile>
- Write debug information to given file
- -V, --version
- Display version information and exit
- -h, --help
- Display help and exit
- -C, --separator=<char>
- Separator for CSV created by operation list (Default Value: ,)
- --power-timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- --shell-timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- --login-timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- --power-wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- --retry-on
- Count of attempts to retry power on (Default Value: 1)
- --delay
- Wait X seconds before fencing is started (Default Value: 0)
ACTIONS
- on
- Power on machine.
- off
- Power off machine.
- reboot
- Reboot machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.
- monitor
- Check if fencing device is running. List available plugs/virtual machines or get status of machine (if it does not support more).
- metadata
The operational behavior of this is not known.
STDIN PARAMETERS
- action
- Fencing Action (Default Value: reboot)
- ipaddr
- IP Address or Hostname This parameter is always required.
- login
- Login Name
- passwd
- Login password or passphrase
- passwd_script
- Script to retrieve password
- port
- Physical plug number or name of virtual machine This parameter is always required.
- snmp_version
- Specifies SNMP version to use (1,2c,3)
- community
- Set the community string
- snmp_auth_prot
- Set authentication protocol (MD5|SHA)
- snmp_sec_level
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- snmp_priv_prot
- Set privacy protocol (DES|AES)
- snmp_priv_passwd
- Set privacy protocol password
- snmp_priv_passwd_script
- Script to run to retrieve privacy password
- udpport
- UDP/TCP port to use for connection with device (Default Value: 161)
- inet4_only
- Forces agent to use IPv4 addresses only
- inet6_only
- Forces agent to use IPv6 addresses only
- verbose
- Verbose mode
- debug
- Write debug information to given file
- version
- Display version information and exit
- help
- Display help and exit
- separator
- Separator for CSV created by operation list (Default Value: ,)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- retry_on
- Count of attempts to retry power on (Default Value: 1)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre