ipmi-oem

Langue: en

Version: 386146 (fedora - 01/12/10)

Section: 8 (Commandes administrateur)

NAME

ipmi-oem - IPMI OEM utility

SYNOPSIS

ipmi-oem [OPTION...] <OEMID> <OEMCOMMAND> [OEMOPTION...]

DESCRIPTION

Ipmi-oem is used to execute OEM specific IPMI commands. It is intended to provide a better user interface for OEM specific IPMI commands rather than using ipmi-raw(8).

Please see SUPPORTED OEM IDS and COMMANDS below for a list of supported OEM specific IPMI commands. A list of supported OEM specific commands may also be generated using the --list option.

There are no guarantees that the below OEM commands will work on any particular motherboard. OEM extensions may or may not exist on particular hardware revisions and/or firmware revisions of motherboards. The extensions may or may not function for other lines of motherboards from the same manufacturer.

Listed below are general IPMI options, tool specific options, trouble shooting information, workaround information, examples, and known issues. For a general introduction to FreeIPMI please see freeipmi(7).

GENERAL OPTIONS

The following options are general options for configuring IPMI communication and executing general tool commands.
-D, --driver-type=IPMIDRIVER
Specify the driver type to use instead of doing an auto selection. The currently available outofband drivers are LAN and LAN_2_0, which perform IPMI 1.5 and IPMI 2.0 respectively. The currently available inband drivers are KCS, SSIF, OPENIPMI, and SUNBMC.
--disable-auto-probe
Do not probe in-band IPMI devices for default settings.
--driver-address=DRIVER-ADDRESS
Specify the in-band driver address to be used instead of the probed value. DRIVER-ADDRESS should be prefixed with "0x" for a hex value and '0' for an octal value.
--driver-device=DEVICE
Specify the in-band driver device path to be used instead of the probed path.
--register-spacing=REGISTER-SPACING
Specify the in-band driver register spacing instead of the probed value.
-h, --hostname=IPMIHOST1,IPMIHOST2,...
Specify the remote host(s) to communicate with. Multiple hostnames may be separated by comma or may be specified in a range format; see HOSTRANGED SUPPORT below.
-u, --username=USERNAME
Specify the username to use when authenticating with the remote host. If not specified, a null (i.e. anonymous) username is assumed. The required user privilege will depend on the oem commands executed.
-p, --password=PASSWORD
Specify the password to use when authenticationg with the remote host. If not specified, a null password is assumed. Maximum password length is 16 for IPMI 1.5 and 20 for IPMI 2.0.
-P, --password-prompt
Prompt for password to avoid possibility of listing it in process lists.
-k, --k-g=K_G
Specify the K_g BMC key to use when authenticating with the remote host for IPMI 2.0. If not specified, a null key is assumed. To input the key in hexadecimal form, prefix the string with '0x'. E.g., the key 'abc' can be entered with the either the string 'abc' or the string '0x616263'
-K, --k-g-prompt
Prompt for k-g to avoid possibility of listing it in process lists.
--session-timeout=MILLISECONDS
Specify the session timeout in milliseconds. Defaults to 20000 milliseconds (20 seconds) if not specified.
--retransmission-timeout=MILLISECONDS
Specify the packet retransmission timeout in milliseconds. Defaults to 1000 milliseconds (1 second) if not specified. The retransmission timeout cannot be larger than the session timeout.
-a, --authentication-type=AUTHENTICATION-TYPE
Specify the IPMI 1.5 authentication type to use. The currently available authentication types are NONE, STRAIGHT_PASSWORD_KEY, MD2, and MD5. Defaults to MD5 if not specified.
-I, --cipher-suite-id=CIPHER-SUITE-ID
Specify the IPMI 2.0 cipher suite ID to use. The Cipher Suite ID identifies a set of authentication, integrity, and confidentiality algorithms to use for IPMI 2.0 communication. The authentication algorithm identifies the algorithm to use for session setup, the integrity algorithm identifies the algorithm to use for session packet signatures, and the confidentiality algorithm identifies the algorithm to use for payload encryption. Defaults to cipher suite ID 3 if not specified. The following cipher suite ids are currently supported:

0 - Authentication Algorithm = None; Integrity Algorithm = None; Confidentiality Algorithm = None

1 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = None; Confidentiality Algorithm = None

2 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = HMAC-SHA1-96; Confidentiality Algorithm = None

3 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = HMAC-SHA1-96; Confidentiality Algorithm = AES-CBC-128

6 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = None; Confidentiality Algorithm = None

7 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = HMAC-MD5-128; Confidentiality Algorithm = None

8 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = HMAC-MD5-128; Confidentiality Algorithm = AES-CBC-128

11 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = MD5-128; Confidentiality Algorithm = None

12 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = MD5-128; Confidentiality Algorithm = AES-CBC-128

-l, --privilege-level=PRIVILEGE-LEVEL
Specify the privilege level to be used. The currently available privilege levels are USER, OPERATOR, and ADMIN. Defaults to ADMIN if not specified.
--config-file=FILE
Specify an alternate configuration file.
-W, --workaround-flags=WORKAROUNDS
Specify workarounds to vendor compliance issues. Multiple workarounds can be specified separated by commas. See WORKAROUNDS below for a list of available workarounds.
--debug
Turn on debugging.
-?, --help
Output a help list and exit.
--usage
Output a usage message and exit.
-V, --version
Output the program version and exit.

SDR CACHE OPTIONS

This tool requires access to the sensor data repository (SDR) cache for general operation. By default, SDR data will be downloaded and cached on the local machine. The following options apply to the SDR cache.
-f, --flush-cache
Flush a cached version of the sensor data repository (SDR) cache. The SDR is typically cached for faster subsequent access. However, it may need to be flushed and re-generated if the SDR has been updated on a system.
-Q, --quiet-cache
Do not output information about cache creation/deletion. May be useful in scripting.
--sdr-cache-directory=DIRECTORY
Specify an alternate directory for sensor data repository (SDR) caches to be stored or read from. Defaults to the home directory if not specified.
--sdr-cache-recreate
If the SDR cache is out of date or invalid, automatically recreate the sensor data repository (SDR) cache. This option may be useful for scripting purposes.

HOSTRANGED OPTIONS

The following options manipulate hostranged output. See HOSTRANGED SUPPORT below for additional information on hostranges.
-B, --buffer-output
Buffer hostranged output. For each node, buffer standard output until the node has completed its IPMI operation. When specifying this option, data may appear to output slower to the user since the the entire IPMI operation must complete before any data can be output. See HOSTRANGED SUPPORT below for additional information.
-C, --consolidate-output
Consolidate hostranged output. The complete standard output from every node specified will be consolidated so that nodes with identical output are not output twice. A header will list those nodes with the consolidated output. When this option is specified, no output can be seen until the IPMI operations to all nodes has completed. If the user breaks out of the program early, all currently consolidated output will be dumped. See HOSTRANGED SUPPORT below for additional information.
-F, --fanout
Specify multiple host fanout. A "sliding window" (or fanout) algorithm is used for parallel IPMI communication so that slower nodes or timed out nodes will not impede parallel communication. The maximum number of threads available at the same time is limited by the fanout. The default is 64.
-E, --eliminate
Eliminate hosts determined as undetected by ipmidetect. This attempts to remove the common issue of hostranged execution timing out due to several nodes being removed from service in a large cluster. The ipmidetectd daemon must be running on the node executing the command.
--always-prefix
Always prefix output, even if only one host is specified or communicating in-band. This option is primarily useful for scripting purposes. Option will be ignored if specified with the -C option.

IPMI-OEM OPTIONS

The following options are specific to Ipmi-oem.
-L, --list
List supported OEM IDs and Commands.
-v, --verbose
Output verbose information. Additional output will depend on specific OEM ID and OEM COMMANDS specified.

SUPPORTED OEM IDS and COMMANDS

The currently supported OEM IDs and COMMANDs are listed below. The special OEM ID of list may be passed into the list all supported OEM IDs and Commands. The special OEM command list may be passed to any OEM ID to list commands supported by that OEM ID.
Dell
get-system-info KEY
This OEM command can retrieve the motherboard system information. Valid keys are guid, asset-tag, service-tag, chassis-service-tag, chassis-related-service-tag, board-revision, platform-model-name, or mac-addresses. Command confirmed to work on Dell Poweredge 2900, 2950, R610, and R710 (Dell 10G and 11G Poweredge systems). However, specific system information may not be readable or available on all systems.
get-nic-selection
This OEM command will determine the current NIC selection for IPMI as dedicated, shared, shared w/ failover to NIC2, or shared w/ failover to all. Dedicated indicates IPMI is only available on an expansion card, shared indicates IPMI is available on NIC1, shared w/ failover to NIC2 indicates IPMI is available on NIC1 w/ failover to NIC2 on NIC1's failure, and shared w/ failover to all indicates IPMI is available on NIC1 w/ failover to all other NICs in the event of NIC failure. Command confirmed to work on Dell Poweredge 2900, 2950, R610, and R710 (Dell 10G and 11G Poweredge systems).
set-nic-section dedicated|shared|shared_failover_nic2|shared_failover_all
This OEM command will set the current NIC selection to dedicated, shared, shared_failover_nic2, or shared_failover_all. (See get-nic-selection above for description on inputs.) On older Poweredge systems, shared_failover_nic2 may have been documented as just failover. Command confirmed to work on Dell Poweredge 2900, 2950, R610, and R710 (Dell 10G and 11G Poweredge systems).
get-active-lom-status
This OEM command will get the current NIC being used for out of band management. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-ssh-config
This OEM command will get the current SSH configuration on the IPMI card. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
set-ssh-config KEY=VALUE ...
This OEM command will set the current SSH configuration on the IPMI card. The possible keys and values are ssh=enable|disable, idletimeout=seconds, and portnumber=num. Multiple key=value pairs may be specified. If no key=value pairs are specifed, available pairs are output. Some fields may be read-only on specific Poweredge systems. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-telnet-config
This OEM command will get the current telnet configuration on the IPMI card. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
set-telnet-config KEY=VALUE ...
This OEM command will set the current Telnet configuration on the IPMI card. The possible keys and values are telnet=enable|disable, sessiontimeout=seconds, portnumber=num, and 7fls=enable|disable. Multiple key=value pairs may be specified. If no key=value pairs are specifed, available pairs are output. Some fields may be read-only on specific Poweredge systems. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-web-server-config
This OEM command will get the current web server configuration on the IPMI card. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
set-web-server-config KEY=VALUE ...
This OEM command will set the current Web Server configuration on the IPMI card. The possible keys and values are webserver=enable|disable, sessiontimeout=seconds, httpportnumber=num, and httpsportnumber=num. Multiple key=value pairs may be specified. If no key=value pairs are specifed, available pairs are output. Some fields may be read-only on specific Poweredge systems. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-active-directory-config
This OEM command will get the current active directory configuration on the IPMI card. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
set-active-directory-config
This OEM command will set the current Web Server configuration on the IPMI card. The possible keys and values are activedirectory=enable|disable, timeout=seconds, type=extended|standard, sso=enable|disable, and certificatevalidation=enable|disable. If no key=value pairs are specifed, available pairs are output. Some fields may be read-only on specific Poweredge systems. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
reset-to-defaults
This OEM command will reset the BMC configuration back to default values. The command will spin until the reset is confirmed to be complete. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-power-consumption-data
This OEM command can retrieve power consumption data. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
reset-power-consumption-data cumulative|peak
This OEM command can reset the cumulative or peak power consumption data (viewed via get-power-consumption-data). Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
power-supply-info
This OEM command can read and output power supply ratings and other information. This OEM command requires access to the SDR. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-instantaneous-power-consumption-data power_supply_instance
This OEM command can read instantaneous power consumption data. If a power supply instance number is specified, only data for that instance will be gathered. Otherwise, collective power consumption will be gathered. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-power-head-room
This OEM command can read power head room. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-power-consumption-statistics average|max|min
This OEM command can read average, max, or min power consumption history. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-power-capacity
This OEM command can read the current power capacity. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
set-power-capacity power-capacity
This OEM command can write the current power capacity (specified in Watts). Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-power-capacity-status
This OEM command can determine if the current power capacity is enabled or disabled. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
set-power-capacity-status enable|disable
This OEM command can configure the current power capacity to be enabled or disabled. Command confirmed to work on Dell Poweredge R610 and R710 (Dell 11G Poweredge systems).
get-chassis-identify-status
This OEM command will retrieve the current chassis identify (i.e. LED) status. Command confirmed to work on Dell Poweredge 2900, 2950, R610, and R710 (Dell 10G and 11G Poweredge systems).
get-board-id
This OEM command can get the board ID. Command confirmed to work on Dell Xanadu II and Dell Xanadu III.
set-board-id ID
This OEM command can set the board ID. Command confirmed to work on Dell Xanadu II and Dell Xanadu III.
get-fcb-version
This OEM command can get the fan control board (FCB) version number. Command confirmed to work on Dell Xanadu II and Dell Xanadu III.
set-fcb-version majorversion minorversion
This OEM command can set the fan control board (FCB) version number. The majorversion and minorversion must be specified in hex. Command confirmed to work on Dell Xanadu II and Dell Xanadu III.
get-sol-inactivity-timeout
This OEM command will retrieve the SOL inactivity timeout. Command confirmed to work on Dell Xanadu II and Dell Xanadu III.
set-sol-inactivity-timeout inactivity-timeout
This OEM command will set the SOL inactivity timeout. The inactivity-timeout is one-based, max of 65535, in 1 minute increments (e.g. 1 = 1 minute), 0 or "none" will configure no timeout. Command confirmed to work on Dell Xanadu II and Dell Xanadu III.
Fujitsu
get-power-on-source
This OEM command will return the reason for the most recent Power On. Command confirmed to work on Fujitsu RX100 S5.
get-power-off-source
This OEM command will return the reason for the most recent Power Off. Command confirmed to work on Fujitsu RX100 S5.
get-remote-storage-status connection_number
This OEM command will return the connection and/or status of remote storage. connection_number currently supports a range of 0-1. Command confirmed to work on Fujitsu RX100 S5.
get-system-status
This OEM command will return the current system status. Command confirmed to work on Fujitsu RX100 S5.
get-eeprom-version-info eeprom_number
This OEM command will return the current version info for various hardware elements, including firmware, SDR, and boot revision. eeprom_number currently supports a range of 0-1. Command confirmed to work on Fujitsu RX100 S5.
get-identify-led
This OEM command will get the current identify LED status. Command confirmed to work on Fujitsu RX100 S5.
set-identify-led on|off
This OEM command will set the current identify LED status. Command confirmed to work on Fujitsu RX100 S5.
get-error-led
This OEM command will get the current error LED status. Command confirmed to work on Fujitsu RX100 S5.
IBM
get-led
This OEM command will get the current LED status. Command confirmed to work on IBM x3755.
Inventec
get-nic-mode
This OEM command will determine the current NIC mode as dedicated or shared. Dedicated indicates IPMI is only available on the dedicated management port. Shared indicates IPMI is also available on one of the primary ethernet ports. Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).
set-nic-mode dedicated|shared
This OEM command will set the current NIC mode to dedicated or shared. (See get-nic-mode above for description on dedicated vs. shared mode.) This OEM command may internally reset the BMC, making the BMC unusable for awhile. Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).
get-mac-address
This command will retrieve the BMC MAC address. This is actually not an OEM command, but rather the normal IPMI MAC address command (identical to what is used in the bmc-config(8) tool). This command is placed here for convenience.
set-mac-address dedicated|shared MACADDR
This OEM command will set the dedicated or shared BMC MAC address. (See get-nic-mode above for description on dedicated vs. shared mode.) The BMC MAC address cannot be set through the normal IPMI MAC address command (what is used in the bmc-config(8) tool). The MACADDR should be specified in XX:XX:XX:XX:XX:XX form. A shared BMC MAC address may conflict with normal communication ethernet communication on the primary ethernet port. Users may wish to configuration an alternate MAC address instead. After configuration of the MAC address, the BMC must be reset. This may be accomplished by executing a cold-reset with bmc-device(8). Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).
get-bmc-services
This OEM command will display the currently enabled BMC services. Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).
set-bmc-services enable|disable all|kvm|http|ssh
This OEM command will enable or disable other BMC services besides IPMI. all can be specified to enable/disable all services, kvm specifies KVM and Virtual Storage, http specifies HTTP and HTTPS, and ssh specifies both SSH and Telnet. Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).
get-authentication-config
This OEM command will display additional OEM authentication settings. (See set-authentication-config below for description on outputs.) Command confirmed to work on Inventec 5441/5442 (and subsequently Dell Xanadu II/III).
set-authentication-config KEY=VALUE ...
This OEM command will set additional OEM authentication settings on the IPMI card. The possible keys and values are maxauthenticationfailures=count, lockoutwindow=seconds, lockouttime=seconds, and httpsportnumber=num. maxauthenticationfailures specifies the maximum number of allowed authentication failures. lockoutwindow specifies the window of time the authentication failure count can be reached in to disable a user. lockouttime specifies the time period a user is disabled if the authentication failure count is reached. Setting 0 to any of the settings will disable the lockout feature. Each time any of these settings is modified, the authentication failure count of each enabled user is reset to 0. Multiple key=value pairs may be specified. If no key=value pairs are specifed, available pairs are output. Command confirmed to work on Inventec 5441/5442 (and subsequently Dell Xanadu II/III).
get-web-server-config
This OEM command will get the current web server configuration on the IPMI card. Command confirmed to work on Inventec 5441/5442 (and subsequently Dell Xanadu II/III).
set-web-server-config KEY=VALUE ...
This OEM command will set the current web server configuration on the IPMI card. The possible keys and values are webserver=enable|disable, webservertimeout=seconds, httpportnumber=num, and httpsportnumber=num. Multiple key=value pairs may be specified. If no key=value pairs are specifed, available pairs are output. Command confirmed to work on Inventec 5441/5442 (Dell Xanadu II/III).
get-power-management-config
This OEM command will get the current power management configuration on the IPMI card. Command confirmed to work on Inventec 5441/5442 (and subsequently Dell Xanadu II/III).
set-power-management-config KEY=VALUE ...
This OEM command will set the current power management configuration on the IPMI card. The possible keys and values are dpnmpowermanagement=enable|disable, powerstaggeringacrecovery=immediate|auto|user, powerondelay=seconds, and maxpowerondelay=seconds. dpnmpowermanagement enables or diables DPNM, Dynamic Power Node Management. For powerstaggeringacrecovery, immediate specifies no delay, auto generates a delay time between the minimum and maximum configured, and user uses the user defined time defined by powerondelay. powerondelay must be within the minimum and maximum power on delay times. Multiple key=value pairs may be specified. If no key=value pairs are specifed, available pairs are output. Command confirmed to work on Inventec 5441/5442 (and subsequently Dell Xanadu II/III).
read-eeprom at24c256n
This OEM command will read the specified eeprom. Command confirmed to work on Inventec 5441 (Dell Xanadu II) for at24c256.
clear-eeprom at24c256n
This OEM command will clear the specified eeprom. If the verbose option is set, progress percent will be output as the clearing is being done. Command confirmed to work on Inventec 5441 (and subsequently Dell Xanadu II) for at24c256.
Quanta
reset-to-defaults all|user|lan|sol|serial|pef
This OEM command will reset certain BMC configuration sections back to default values. The command will spin until the reset is confirmed to be complete. Command confirmed to work on Quanta S99Q (Dell TS12-TY). After running this command, the BMC must be reset to return it to functioning status. This may be accomplished by executing a cold-reset with bmc-device(8).
get-processor-information [processor-index]
This OEM command will determine system processor information. By default, information about each processor will be output. If a processor_index is specified, only that specific processor will be output. Command confirmed to work on Quanta S99Q (Dell TS12-TY).
Sun
get-led
This OEM command will output current LED mode. off indicates the LED is steady off, on indicates the LED is steady on, standby indicates teh LED blinks at a 100ms on, 2900ms off rate, slow indicates the LED is blinking at 1Hz, and fast indicates the LED is blinking at 4Hz. If the verbose option is set, sensor names will be output with their entity ID and instance when appropriate. (Similar to the --entity-sensor-names options in ipmi-sensors and ipmimonitoring.) Command confirmed to work on Sun Fire 4140 with ILOM.
set-led record_id off|on|standby|slow|fast
This OEM command will configure LED modes. (See get-led above for description on LED modes.) Command confirmed to work on Sun Fire 4140 with ILOM.
Supermicro
extra-firmware-info
This OEM command will output additional firmware version information. Command confirmed to work on Supermicro H8QME.
reset-intrusion
This OEM command will reset the motherboard intrusion flag after it has been triggered. For example, in ipmi-sensors or ipmi-sel, you may notice a 'General Chassis Intrusion' if the motherboard chassis is not open, but was opened in the past. Command confirmed to work on Supermicro H8QME.
get-bmc-services-status
This OEM command will determine if non-IPMI services (e.g. ssh, http, https, vnc, etc.) are currently enabled or disabled on the BMC. Command confirmed to work on Supermicro X8DTG.
set-bmc-services-status enable|disable
This OEM command will enable or disable all non-IPMI services on the BMC. This command can be used to enable or disable non-IPMI services such as ssh, http, https, and vnc. Command confirmed to work on Supermicro X8DTG.

HOSTRANGED SUPPORT

Multiple hosts can be input either as an explicit comma separated lists of hosts or a range of hostnames in the general form: prefix[n-m,l-k,...], where n < m and l < k, etc. The later form should not be confused with regular expression character classes (also denoted by []). For example, foo[19] does not represent foo1 or foo9, but rather represents a degenerate range: foo19.

This range syntax is meant only as a convenience on clusters with a prefixNN naming convention and specification of ranges should not be considered necessary -- the list foo1,foo9 could be specified as such, or by the range foo[1,9].

Some examples of range usage follow:

     foo[01-05] instead of foo01,foo02,foo03,foo04,foo05
     foo[7,9-10] instead of foo7,foo9,foo10
     foo[0-3] instead of foo0,foo1,foo2,foo3
 

As a reminder to the reader, some shells will interpret brackets ([ and ]) for pattern matching. Depending on your shell, it may be necessary to enclose ranged lists within quotes.

When multiple hosts are specified by the user, a thread will be executed for each host in parallel up to the configured fanout (which can be adjusted via the -F option). This will allow communication to large numbers of nodes far more quickly than if done in serial.

By default, standard output from each node specified will be output with the hostname prepended to each line. Although this output is readable in many situations, it may be difficult to read in other situations. For example, output from multiple nodes may be mixed together. The -B and -C options can be used to change this default.

In-band IPMI Communication will be used when the host "localhost" is specified. This allows the user to add the localhost into the hostranged output.

GENERAL TROUBLESHOOTING

Most often, IPMI problems are due to configuration problems. Inband IPMI problems are typically caused by improperly configured drivers or non-standard BMCs. IPMI over LAN problems involve a misconfiguration of the remote machine's BMC. Double check to make sure the following are configured properly in the remote machine's BMC: IP address, MAC address, subnet mask, username, user enablement, user privilege, password, LAN privilege, LAN enablement, and allowed authentication type(s). For IPMI 2.0 connections, double check to make sure the cipher suite privilege(s) and K_g key are configured properly. The bmc-config(8) tool can be used to check and/or change these configuration settings.

The following are common issues for given error messages:

"username invalid" - The username entered (or a NULL username if none was entered) is not available on the remote machine. It may also be possible the remote BMC's username configuration is incorrect.

"password invalid" - The password entered (or a NULL password if none was entered) is not correct. It may also be possible the password for the user is not correctly configured on the remote BMC.

"password verification timeout" - Password verification has timed out. A "password invalid" error (described above) or a generic "session timeout" (described below) occurred. During this point in the protocol it cannot be differentiated which occurred.

"k_g invalid" - The K_g key entered (or a NULL K_g key if none was entered) is not correct. It may also be possible the K_g key is not correctly configured on the remote BMC.

"privilege level insufficient" - An IPMI command requires a higher user privilege than the one authenticated with. Please try to authenticate with a higher privilege. This may require authenticating to a different user which has a higher maximum privilege.

"privilege level cannot be obtained for this user" - The privilege level you are attempting to authenticate with is higher than the maximum allowed for this user. Please try again with a lower privilege. It may also be possible the maximum privilege level allowed for a user is not configured properly on the remote BMC.

"authentication type unavailable for attempted privilege level" - The authentication type you wish to authenticate with is not available for this privilege level. Please try again with an alternate authentication type or alternate privilege level. It may also be possible the available authentication types you can authenticate with are not correctly configured on the remote BMC.

"cipher suite id unavailable" - The cipher suite id you wish to authenticate with is not available on the remote BMC. Please try again with an alternate cipher suite id. It may also be possible the available cipher suite ids are not correctly configured on the remote BMC.

"ipmi 2.0 unavailable" - IPMI 2.0 was not discovered on the remote machine. Please try to use IPMI 1.5 instead.

"connection timeout" - Initial IPMI communication failed. A number of potential errors are possible, including an invalid hostname specified, an IPMI IP address cannot be resolved, IPMI is not enabled on the remote server, the network connection is bad, etc. Please verify configuration and connectivity.

"session timeout" - The IPMI session has timed out. Please reconnect. If this error occurs often, you may wish to increase the retransmission timeout. Some remote BMCs are considerably slower than others.

"device not found" - The specified device could not be found. Please check configuration or inputs and try again.

"driver timeout" - Communication with the driver or device has timed out. Please try again.

"message timeout" - Communication with the driver or device has timed out. Please try again.

"BMC busy" - The BMC is currently busy. It may be processing information or have too many simultaneous sessions to manage. Please wait and try again.

"could not find inband device" - An inband device could not be found. Please check configuration or specify specific device or driver on the command line.

Please see WORKAROUNDS below to also if there are any vendor specific bugs that have been discovered and worked around.

WORKAROUNDS

With so many different vendors implementing their own IPMI solutions, different vendors may implement their IPMI protocols incorrectly. The following lists the workarounds currently available to handle discovered compliance issues.

When possible, workarounds have been implemented so they will be transparent to the user. However, some will require the user to specify a workaround be used via the -W option.

The hardware listed below may only indicate the hardware that a problem was discovered on. Newer versions of hardware may fix the problems indicated below. Similar machines from vendors may or may not exhibit the same problems. Different vendors may license their firmware from the same IPMI firmware developer, so it may be worthwhile to try workarounds listed below even if your motherboard is not listed.

"idzero" - This workaround option will allow empty session IDs to be accepted by the client. It works around IPMI sessions that report empty session IDs to the client. Those hitting this issue may see "session timeout" errors. Issue observed on Tyan S2882 with M3289 BMC.

"unexpectedauth" - This workaround option will allow unexpected non-null authcodes to be checked as though they were expected. It works around an issue when packets contain non-null authentication data when they should be null due to disabled per-message authentication. Those hitting this issue may see "session timeout" errors. Issue observed on Dell PowerEdge 2850,SC1425. Confirmed fixed on newer firmware.

"forcepermsg" - This workaround option will force per-message authentication to be used no matter what is advertised by the remote system. It works around an issue when per-message authentication is advertised as disabled on the remote system, but it is actually required for the protocol. Those hitting this issue may see "session timeout" errors. Issue observed on IBM eServer 325.

"endianseq" - This workaround option will flip the endian of the session sequence numbers to allow the session to continue properly. It works around IPMI 1.5 session sequence numbers that are the wrong endian. Those hitting this issue may see "session timeout" errors. Issue observed on some Sun ILOM 1.0/2.0 (depends on service processor endian).

"authcap" - This workaround option will skip early checks for username capabilities, authentication capabilities, and K_g support and allow IPMI authentication to succeed. It works around multiple issues in which the remote system does not properly report username capabilities, authentication capabilities, or K_g status. Those hitting this issue may see "username invalid", "authentication type unavailable for attempted privilege level", or "k_g invalid" errors. Issue observed on Asus P5M2/P5MT-R/RS162-E4/RX4, Intel SR1520ML/X38ML, and Sun Fire 2200/4150/4450 with ELOM.

"intel20" - This workaround option will work around several Intel IPMI 2.0 authentication issues. The issues covered include padding of usernames, automatic acceptance of a RAKP 4 response integrity check when using the integrity algorithm MD5-128, and password truncation if the authentication algorithm is HMAC-MD5-128. Those hitting this issue may see "username invalid", "password invalid", or "k_g invalid" errors. Issue observed on Intel SE7520AF2 with Intel Server Management Module (Professional Edition).

"supermicro20" - This workaround option will work around several Supermicro IPMI 2.0 authentication issues on motherboards w/ Peppercon IPMI firmware. The issues covered include handling invalid length authentication codes. Those hitting this issue may see "password invalid" errors. Issue observed on Supermicro H8QME with SIMSO daughter card. Confirmed fixed on newerver firmware.

"sun20" - This workaround option will work work around several Sun IPMI 2.0 authentication issues. The issues covered include invalid lengthed hash keys, improperly hashed keys, and invalid cipher suite records. Those hitting this issue may see "password invalid" or "bmc error" errors. Issue observed on Sun Fire 4100/4200/4500 with ILOM. This workaround automatically includes the "opensesspriv" workaround.

"opensesspriv" - This workaround option will slightly alter FreeIPMI's IPMI 2.0 connection protocol to workaround an invalid hashing algorithm used by the remote system. The privilege level sent during the Open Session stage of an IPMI 2.0 connection is sometimes invalid and used for hashing keys instead of the privilege level sent during the RAKP1 connection stage. Those hitting this issue may see "password invalid", "k_g invalid", "bad rmcpplus status code", or "privilege level cannot be obtained for this user " errors. Issue observed on Sun Fire 4100/4200/4500 with ILOM, Inventec 5441/Dell Xanadu II, Supermicro X8DTH, Supermicro X8DTG, Supermicro X8DTU, and Intel S5500WBV/Penguin Relion 700. This workaround is automatically triggered with the "sun20" workaround.

"integritycheckvalue" - This workaround option will work around an invalid integrity check value during an IPMI 2.0 session establishment when using Cipher Suite ID 0. The integrity check value should be 0 length, however the remote motherboard responds with a non-empty field. Those hitting this issue may see "k_g invalid" errors. Issue observed on Supermicro X8DTG, Supermicro X8DTU, and Intel S5500WBV/Penguin Relion 700.

KNOWN ISSUES

On older operating systems, if you input your username, password, and other potentially security relevant information on the command line, this information may be discovered by other users when using tools like the ps(1) command or looking in the /proc file system. It is generally more secure to input password information with options like the -P or -K options. Configuring security relevant information in the FreeIPMI configuration file would also be an appropriate way to hide this information.

In order to prevent brute force attacks, some BMCs will temporarily "lock up" after a number of remote authentication errors. You may need to wait awhile in order to this temporary "lock up" to pass before you may authenticate again.

REPORTING BUGS

Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>. Copyright © 2008-2010 FreeIPMI Core Team

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

SEE ALSO

freeipmi(7), bmc-config(8), bmc-device(8), ipmi-raw(8)

http://www.gnu.org/software/freeipmi/