Rechercher une page de manuel
smp_discover
Langue: en
Version: 175806 (fedora - 06/07/09)
Section: 8 (Commandes administrateur)
Sommaire
NAME
smp_discover - invoke DISCOVER SMP functionSYNOPSIS
smp_discover [--brief] [--help] [--hex] [--ignore] [--interface=PARAMS] [--list] [--multiple] [--num=NUM] [--phy=ID] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] SMP_DEVICE[,N]DESCRIPTION
Sends a SAS Management Protocol (SMP) DISCOVER request function to a SMP target and decodes or outputs the response. The SMP target is identified by the SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. With one interface there is one SMP_DEVICE per machine so the SMP_DEVICE,N syntax is needed to differentiate between HBAs if there are multiple present.
OPTIONS
Mandatory arguments to long options are mandatory for short options as well.- -b, --brief
- reduce the decoded response output. If used twice will exit if there is no attached device (after outputting that). When used with --multiple, unattached phys are not listed; when used twice, trims attached phys output.
- -h, --help
- output the usage message then exit.
- -H, --hex
- output the response in hexadecimal.
- -i, --ignore
- sets the Ignore Zone Group bit in the SMP Discover request.
- -I, --interface=PARAMS
- interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See the smp_utils man page for more information.
- -l, --list
- list attributes in "name=value" form, one entry per line.
- -m, --multiple
- loops over multiple phys within SMP target (typically an expander) and does a DISCOVER request and outputs a one line summary. Phy 0 is queried first, then phy 1, continuing until an error occurs. If --brief is given then there is no output for phys that indicate there is no attached device; when used twice additionally trims the output line of attached phys.
- -n, --num=NUM
- number of phys to fetch, starting at --phy=ID when the --multiple option is given. The default value is 0 which is interpreted as "the rest" (i.e. until a "phy does not exist" function result is received). This option is ignored in the absence of the --multiple option.
- -p, --phy=ID
- phy identifier. ID is a value between 0 and 127. Default is 0.
- -r, --raw
- send the response to stdout in binary. All error messages are sent to stderr.
- -s, --sa=SAS_ADDR
- specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.
- -v, --verbose
- increase the verbosity of the output. Can be used multiple times
- -V, --version
- print the version string and then exit.
SINGLE LINE FORMAT
The --multiple option causes SMP DISCOVER responses to be compressed to a header followed by one line per phy. To save space SAS addresses are shown in hex without a '0x' prefix or 'h' suffix. The header line gives the SAS address of the SMP target itself and assumes it is an expander.Each line starts with " phy <n>:" where <n> is the phy identifier (and they are origin zero). That is followed by the routing attribute represented by a single letter which is either "D" for direct routing, "S" to subtractive routing or "T" for table routing. Then comes the negotiated physical link rate which is either "disabled", "reset problem" or "spinup hold". Other states are mapped to "attached". This includes enabled phys with nothing connected which appear as "attached:[0000000000000000:00]".
Information shown between the brackets is for the attached device. Phys that are connected display something like: "attached:[5000c50000520a2a:01 " where the first number is the attached SAS address (in hex) and the second number is the attached device's phy identifier. If the attached device type is other than an end device then one of these abbreviations is output: "exp" (for expander), "fex" (for fanout expander) or "res" (for unknown attached device type). If a phy is flagged as "virtual" then the letter "V" appears next. Next are the protocols supported by the attached device which are shown as "i(<list>)" for initiator protocols and/or "t(<list>)" for target protocols. The <list> is made up of "PORT_SEL", "SSP", "STP", "SMP" and "SATA" with "+" used as a separator. For example a SAS host adapter wi11 most likely appear as: "i(SSP+STP+SMP)". This completes the information about the attached phy, hence the closing right bracket.
Finally, if appropriate, the negotiated physical link rate is shown in gigabits per second. Here is an example of a line for expander phy identifier 11 connected to a SATA target (or SATA "device" to use the t13.org term):
phy 11:T:attached:[500605b000000afb:00 t(SATA)] 1.5 Gbps
CONFORMING TO
The SMP DISCOVER function was introduced in SAS-1, with small additions in SAS-1.1 . There have been a large number of additions in SAS-2 .AUTHORS
Written by Douglas Gilbert.REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.COPYRIGHT
Copyright © 2006-2008 Douglas GilbertThis software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
smp_utils, smp_discover_list, smp_phy_controlContenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre