Rechercher une page de manuel
bus_alloc_resource.9freebsd
Langue: en
Version: 308355 (debian - 07/07/09)
Section: 9 (Appels noyau Linux)
BSD mandoc
NAME
bus_alloc_resource bus_alloc_resource_any - allocate resources from a parent busSYNOPSIS
In sys/param.h In sys/bus.hIn machine/bus.h In sys/rman.h In machine/resource.h Ft struct resource * Fn bus_alloc_resource device_t dev int type int *rid u_long start u_long end u_long count u_int flags Ft struct resource * Fn bus_alloc_resource_any device_t dev int type int *rid u_int flags
DESCRIPTION
This is an easy interface to the resource-management functions. It hides the indirection through the parent's method table. This function generally should be called in attach, but (except in some rare cases) never earlier.The Fn bus_alloc_resource_any function is a convenience wrapper for Fn bus_alloc_resource . It sets the values for Fa start , Fa end , and Fa count to the default resource (see description of Fa start below).
The arguments are as follows:
- Fa dev
- is the device that requests ownership of the resource. Before allocation, the resource is owned by the parent bus.
- Fa type
- is the type of resource you want to allocate. It is one of:
- SYS_RES_IRQ
- for IRQs
- SYS_RES_DRQ
- for ISA DMA lines
- SYS_RES_IOPORT
- for I/O ports
- SYS_RES_MEMORY
- for I/O memory
- Fa rid
- points to a bus specific handle that identifies the resource being allocated. For ISA this is an index into an array of resources that have been setup for this device by either the PnP mechanism, or via the hints mechanism. For PCCARD, this is an index into the array of resources described by the PC Card's CIS entry. For PCI, the offset into pci config space which has the BAR to use to access the resource. The bus methods are free to change the RIDs that they are given as a parameter. You must not depend on the value you gave it earlier.
- Fa start
- and Fa end are the start/end addresses of the resource. If you specify values of 0ul for Fa start and ~0ul for Fa end and 1 for Fa count , the default values for the bus are calculated.
- Fa count
- is the size of the resource. For example, the size of an I/O port is usually 1 byte (but some devices override this). If you specified the default values for Fa start and Fa end , then the default value of the bus is used if Fa count is smaller than the default value and Fa count is used, if it is bigger than the default value.
- Fa flags
- sets the flags for the resource. You can set one or more of these flags:
- RF_ALLOCATED
- resource has been reserved. The resource still needs to be activated with bus_activate_resource9.
- RF_ACTIVE
- activate resource atomically.
- RF_SHAREABLE
- resource permits contemporaneous sharing. It should always be set unless you know that the resource cannot be shared. It is the bus driver's task to filter out the flag if the bus does not support sharing. For example, pccard(4) cannot share IRQs while cardbus(4) can.
- RF_TIMESHARE
- resource permits time-division sharing.
RETURN VALUES
A pointer to struct resource is returned on success, a null pointer otherwise.EXAMPLES
This is some example code that allocates a 32 byte I/O port range and an IRQ. The values of portid and irqid should be saved in the softc of the device after these calls.struct resource *portres, *irqres; int portid, irqid; portid = 0; irqid = 0; portres = bus_alloc_resource(dev, SYS_RES_IOPORT, &portid, 0ul, ~0ul, 32, RF_ACTIVE); irqres = bus_alloc_resource_any(dev, SYS_RES_IRQ, &irqid, RF_ACTIVE | RF_SHAREABLE);
SEE ALSO
bus_activate_resource9, bus_release_resource9, device(9), driver(9)AUTHORS
An -nosplit This manual page was written by An Alexander Langer Aq alex@big.endian.de with parts by An Warner Losh Aq imp@FreeBSD.org .Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre