Linux Certif

Toute la documentation sur la certification Linux LPI

enum_ieee80211_hw_flags

NAME

enum_ieee80211_hw_flags - hardware flags

SYNOPSIS

 enum ieee80211_hw_flags {
   IEEE80211_HW_HAS_RATE_CONTROL,
   IEEE80211_HW_RX_INCLUDES_FCS,
   IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING,
   IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE,
   IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE,
   IEEE80211_HW_SIGNAL_UNSPEC,
   IEEE80211_HW_SIGNAL_DBM,
   IEEE80211_HW_SPECTRUM_MGMT,
   IEEE80211_HW_AMPDU_AGGREGATION,
   IEEE80211_HW_SUPPORTS_PS,
   IEEE80211_HW_PS_NULLFUNC_STACK,
   IEEE80211_HW_SUPPORTS_DYNAMIC_PS,
   IEEE80211_HW_MFP_CAPABLE,
   IEEE80211_HW_BEACON_FILTER,
   IEEE80211_HW_SUPPORTS_STATIC_SMPS,
   IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS,
   IEEE80211_HW_SUPPORTS_UAPSD,
   IEEE80211_HW_REPORTS_TX_ACK_STATUS,
   IEEE80211_HW_CONNECTION_MONITOR,
   IEEE80211_HW_SUPPORTS_CQM_RSSI
 };  
 

CONSTANTS

IEEE80211_HW_HAS_RATE_CONTROL

The hardware or firmware includes rate control, and cannot be controlled by the stack. As such, no rate control algorithm should be instantiated, and the TX rate reported to userspace will be taken from the TX status instead of the rate control algorithm. Note that this requires that the driver implement a number of callbacks so it has the correct information, it needs to have the set_rts_threshold callback and must look at the BSS config use_cts_prot for G/N protection, use_short_slot for slot timing in 2.4 GHz and use_short_preamble for preambles for CCK frames.

IEEE80211_HW_RX_INCLUDES_FCS

Indicates that received frames passed to the stack include the FCS at the end.

IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING

Some wireless LAN chipsets buffer broadcast/multicast frames for power saving stations in the hardware/firmware and others rely on the host system for such buffering. This option is used to configure the IEEE 802.11 upper layer to buffer broadcast and multicast frames when there are power saving stations so that the driver can fetch them with ieee80211_get_buffered_bc.

IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE

Hardware is not capable of short slot operation on the 2.4 GHz band.

IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE

Hardware is not capable of receiving frames with short preamble on the 2.4 GHz band.

IEEE80211_HW_SIGNAL_UNSPEC

Hardware can provide signal values but we don't know its units. We expect values between 0 and max_signal. If possible please provide dB or dBm instead.

IEEE80211_HW_SIGNAL_DBM

Hardware gives signal values in dBm, decibel difference from one milliwatt. This is the preferred method since it is standardized between different devices. max_signal does not need to be set.

IEEE80211_HW_SPECTRUM_MGMT

Hardware supports spectrum management defined in 802.11h Measurement, Channel Switch, Quieting, TPC

IEEE80211_HW_AMPDU_AGGREGATION

Hardware supports 11n A-MPDU aggregation.

IEEE80211_HW_SUPPORTS_PS

Hardware has power save support (i.e. can go to sleep).

IEEE80211_HW_PS_NULLFUNC_STACK

Hardware requires nullfunc frame handling in stack, implies stack support for dynamic PS.

IEEE80211_HW_SUPPORTS_DYNAMIC_PS

Hardware has support for dynamic PS.

IEEE80211_HW_MFP_CAPABLE

Hardware supports management frame protection (MFP, IEEE 802.11w).

IEEE80211_HW_BEACON_FILTER

Hardware supports dropping of irrelevant beacon frames to avoid waking up cpu.

IEEE80211_HW_SUPPORTS_STATIC_SMPS

Hardware supports static spatial multiplexing powersave, ie. can turn off all but one chain even on HT connections that should be using more chains.

IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS

Hardware supports dynamic spatial multiplexing powersave, ie. can turn off all but one chain and then wake the rest up as required after, for example, rts/cts handshake.

IEEE80211_HW_SUPPORTS_UAPSD

Hardware supports Unscheduled Automatic Power Save Delivery (U-APSD) in managed mode. The mode is configured with conf_tx operation.

IEEE80211_HW_REPORTS_TX_ACK_STATUS

Hardware can provide ack status reports of Tx frames to the stack.

IEEE80211_HW_CONNECTION_MONITOR

The hardware performs its own connection monitoring, including periodic keep-alives to the AP and probing the AP on beacon loss. When this flag is set, signaling beacon-loss will cause an immediate change to disassociated state.

IEEE80211_HW_SUPPORTS_CQM_RSSI

Hardware can do connection quality monitoring - i.e. it can monitor connection quality related parameters, such as the RSSI level and provide notifications if configured trigger levels are reached.

DESCRIPTION

These flags are used to indicate hardware capabilities to the stack. Generally, flags here should have their meaning done in a way that the simplest hardware doesn't need setting any particular flags. There are some exceptions to this rule, however, so you are advised to review these flags carefully.

AUTHOR

Johannes Berg <johannes@sipsolutions.net>

Author.

COPYRIGHT