Rechercher une page de manuel
ahcpd
Langue: en
Version: 363826 (ubuntu - 25/10/10)
Section: 8 (Commandes administrateur)
NAME
ahcpd - ad-hoc configuration daemonSYNOPSIS
ahcpd option... [ -- ] interface...DESCRIPTION
AHCP is a configuration protocol that can replace DHCP on networks without transitive connectivity, such as mesh networks.OPTIONS
- -m multicast-address
- Speficy the link-local multicast address to be used by AHCP.
- -p port
- Specify the UDP port number to be used by AHCP.
- -n
- Operate as a forwarder: participate in the flooding protocol, but don't actually perform any configuration.
- -4
- Only attempt to configure IPv4 addresses.
- -6
- Only attempt to configure IPv6 addresses.
- -N
- Do not configure DNS.
- -t time
- Specify the time, in seconds, for which leases are requested. The default is slightly over one hour.
- -s script
- Specify the configuration script to run. The default is /etc/ahcp/ahcp-config.sh.
- -d level
- Set the debug level to level (default 1).
- -i filename
- Specify the filename containing this host's unique id. The default is /var/lib/ahcp-unique-id. If it doesn't exist, it will be created by ahcpd.
- -c filename
- Specify the name of the configuration file. The default is /etc/babeld.conf.
- -C statement
- Specify a configuration statement directly on the command line.
- -D
- Daemonise at startup.
- -L logfile
- Specify a file to log random ``how do you do?'' messages to. This defaults to standard error if not daemonising, and to /var/log/ahcpd.log otherwise.
- -I pidfile
- Specify a file to write our process id to.
CONFIGURATION FILE FORMAT
The configuration is a sequence of lines, each of which starts with one of the keywords below. Blank lines are ignored. Comments are introduced with an octothorp ``#'' and terminate at the end of the line.The following keywords are recognised:
- mode server|client|forwarder
- Specifies whether the daemon operates as a server, a client, or a forwarder. If omitted, the default is to operate as a client, unless the -n flag is present on the command line. If present, this must be the first line in the configuration file.
- prefix prefix
- Specifies either a prefix to use for configuring clients. This keyword is only valid in server configurations, and may be specified twice, once for IPv4 and once for IPv6.
- name-server address
- Specifies the address of a DNS server to configure clients with. This keyword is only valid in server configurations, and may be repeated multiple times.
- ntp-server address
- Specifies the address of an NTP server to configure clients with. This keyword is only valid in server configurations, and may be repeated multiple times.
FILES
- /var/lib/ahcp-unique-id
- An 8-byte long file containing this host's unique id. If it doesn't exist, a new unique id will be generated from an interface's MAC address.
- /etc/ahcp/ahcp-config.sh
- The script that performs the actual configuration. It will be passed one argument, which is either start or stop.
- /etc/ahcp/ahcp-local.sh
- If this is an executable script, it will be called by ahcp-config.sh just after configuring or deconfiguring. It will be passed one argument, which is either start or stop.
SIGNALS
- SIGUSR1
- Print ahcpd's status to standard output or to the log file.
- SIGUSR2
- Check all interfaces for status changes, then reopen the log file.
NOTES
Since the AHCP protocol is designed for mesh networks, it doesn't have any provisions for setting routing parameters such as a default gateway, the IPv4 network mask and the IPv6 list of on-link prefixes; these are expected to be provided by a full-fledged routing protocol for mesh nodes, and by router advertisements for ordinary nodes.The AHCP server should use NTP to synchronise its clock. If a server instance of ahcpd doesn't detect time synchronisation, it will only give out leases for a short period of time, and be extremely conservative about releasing them. Note that an SNTP client is not enough --- ahcpd actually checks with the kernel for time synchronisation, so real NTP is necessary.
SEE ALSO
dhcpcd(8), dhclient(8), babel(8), olsrd(8), ntpd(8), The Ad-Hoc Configuration Protocol.AUTHOR
Juliusz Chroboczek.Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre